B1820/55 Short in Front Driver Side - Side Squib Circuit
Diagnostic trouble codes · Vehicles built from Aug 2013
Also covers:
- B1821/55 Open in Front Driver Side - Side Squib Circuit
- B1822/55 Short to GND in Front Driver Side - Side Squib Circuit
- B1823/55 Short to B+ in Front Driver Side - Side Squib Circuit
Versions by build date: Jun 2011 – Jul 2013 from Aug 2013
DESCRIPTION
The driver side - side squib circuit consists of the center airbag sensor and the driver side - side airbag.The circuit instructs the SRS to deploy when the deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.
| DTC Code |
Detection Condition |
Trouble Area |
| B1820/55 |
When all conditions below are met:
|
|
| B1821/55 |
When all conditions below are met:
|
|
| B1822/55 |
When all conditions below are met:
|
|
| B1823/55 |
When all conditions below are met:
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK VEHICLE CONDITION |
Check vehicle condition.
Result Result
Proceed to
for LHD
A
for RHD
B
|
|
||||
| A | |
| 2. CHECK FRONT SEAT SIDE AIRBAG LH (SIDE SQUIB LH) |
![]() ![]() |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the front seat side airbag LH.
Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front seat side airbag LH (side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- SST
- 09843-18061
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1820, B1821, B1822 or B1823 is not output
- HINT:
- Codes other than DTC B1820, B1821, B1822, B1823 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 3. CHECK FLOOR WIRE (SIDE SQUIB LH CIRCUIT) |
![]() ![]() |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connectors from the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
S39-1 (SFL+) - Body ground
Ignition switch ON
Below 1 V
S39-2 (SFL-) - Body ground
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
S39-1 (SFL+) - S39-2 (SFL-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
S39-1 (SFL+) - S39-2 (SFL-)
Always
1 MΩ or higher
S39-1 (SFL+) - Body ground
S39-2 (SFL-) - Body ground
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() ![]() |
Connect the connectors to the front seat side airbag LH and the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1820, B1821, B1822 or B1823 is not output
- HINT:
- Codes other than DTC B1820, B1821, B1822, B1823 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 5. CHECK FRONT SEAT SIDE AIRBAG ASSEMBLY RH |
![]() ![]() |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect the connector from the front seat side airbag RH.
Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front seat side airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1820, B1821, B1822 or B1823 is not output
- HINT:
- Codes other than DTC B1820, B1821, B1822 or B1823 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 6. CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT) |
![]() ![]() |
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connectors from the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
S38-1 (SFR+) - Body ground
Ignition switch ON
Below 1 V
S38-2 (SFR-) - Body ground
Turn the ignition switch OFF.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
S38-1 (SFR+) - S38-2 (SFR-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
S38-1 (SFR+) - S38-2 (SFR-)
Always
1 MΩ or higher
S38-1 (SFR+) - Body ground
S38-2 (SFR-) - Body ground
|
|
||||
| OK | |
| 7. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
![]() ![]() |
Connect the connectors to the front seat side airbag RH and the center airbag sensor.
Connect the negative (-) terminal cable to the battery, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1820, B1821, B1822 or B1823 is not output
- HINT:
- Codes other than B1820, B1821, B1822 or B1823 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||






