P1264 VN Turbo Controller Malfunction
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The turbocharger system is comprised of the Variable Nozzle (VN) type turbocharger, the turbo motor driver and ECM.The turbocharger has a nozzle vane which opens and closes to control the volume of the exhaust gas flowing into the turbine. This, in turn, controls the boost pressure. When the nozzle vane moves towards the closing direction, the pressure increases. When the vane moves towards the opening direction, the pressure decreases.
The turbocharger actuator built on the turbocharger activates the nozzle vane. The nozzle vane position sensor built on the actuator detects the opening angle of nozzle vane. The turbo motor driver receives an opening angle request from the ECM and a nozzle vane position sensor signal. Based on these signals, the turbo motor driver operates the DC motor and controls the turbocharger's opening angle. The turbo motor driver sends the status as a turbo driver status signal to the ECM
The ECM sends an opening angle request signal to the turbo motor driver to obtain the nozzle vane position for the optimal boost pressure in accordance with the driving conditions.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P1264 |
When communication error occurs between turbo motor and ECM (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. INSPECT TURBO MOTOR DRIVER |
Disconnect the T8 turbo motor driver connector.

Turn the ignition switch ON.
Measure the voltage of the turbo motor driver connector.
- Standard voltage:
Tester Connection
Specified Condition
+B (T8-3) - GND (T8-4)
11 to 14 V
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM) |
Disconnect the E8 ECM connector.

Disconnect the T8 turbo motor driver connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
VNTO (E8-10) - VNTO (T8-7)
Below 1 Ω
VNTI (E8-17) - VNTI (T8-2)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
VNTO (E8-10) or VNTO (T8-7) - Body ground
10 kΩ or higher
VNTI (E8-17) or VNTI (T8-2) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT ECM (VNTO VOLTAGE) |
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

- Standard voltage:
Tester Connection
Specified Condition
VNTO (E8-10) - E1 (E7-7)
Correct waveform is as shown
|
|
||||
| OK | |
| 4. INSPECT TURBO MOTOR DRIVER (VNTI VOLTAGE) |
While idling the engine, check the waveform of the ECM connectors using an oscilloscope.

- Standard voltage:
Tester Connection
Specified Condition
VNTI (E8-17) - E1 (E7-7)
Correct waveform is as shown
|
|
||||
| OK | ||
| ||
