P2563 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Range/Performance
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Also covers:
- P2564 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low
- P2565 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High
- P2588 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit Low
- P2589 Turbocharger/Supercharger Boost Control Position Sensor "B" Circuit High
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the turbo motor driver. The turbo motor driver determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2563 |
Difference between VTA1 and VTA2 0.8 V or more for 0.5 seconds or more (1 trip detection logic) |
Nozzle vane position sensor (Turbocharger sub-assembly) |
| P2564 |
VTA1 0.5 V or less for 0.5 seconds or more (1 trip detection logic) |
|
| P2565 |
VTA1 4.5 V or more for 0.5 seconds or more (1 trip detection logic) |
|
| P2588 |
VTA2 0.5 V or less for 0.5 seconds or more (1 trip detection logic) |
|
| P2589 |
VTA2 4.5 V or more for 0.5 seconds or more (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2563) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P2563, P2564, P2565, P2588 and/or P2589
A
P2563, P2564, P2565, P2588 and/or P2589, and other DTCs
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (NOZZLE VANE POSITION SENSOR - TURBO MOTOR DRIVER) |
Disconnect the T11 nozzle vane position sensor connector.

Disconnect the T8 turbo motor driver connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
VTA1 (T11-1) - VTA1 (T8-9)
Below 1 Ω
VNE2 (T11-2) - VNE2 (T8-8)
Below 1 Ω
VNVC (T11-3) - VNVC (T8-1)
Below 1 Ω
VTA2 (T11-4) - VTA2 (T8-10)
Below 1 Ω
E2S (T11-5) - E2S (T8-11)
Below 1 Ω
VCS (T11-6) - VCS (T8-6)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
VTA1 (T11-1) or VTA1 (T8-9) - Body ground
10 kΩ or higher
VNE2 (T11-2) or VNE2 (T8-8) - Body ground
10 kΩ or higher
VNVC (T11-3) or VNVC (T8-1) - Body ground
10 kΩ or higher
VTA2 (T11-4) or VTA2 (T8-10) - Body ground
10 kΩ or higher
E2S (T11-5) or E2S (T8-11) - Body ground
10 kΩ or higher
VCS (T11-6) or VCS (T8-6) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT TURBO MOTOR DRIVER |
Disconnect the T11 nozzle vane position sensor connector.

Turn the ignition switch ON.
Measure the voltage between the terminals of the nozzle vane position sensor connector.
- Standard voltage:
Tester Connection
Specified Condition
VNVC (T11-3) - VNE2 (T11-2)
4.5 to 5.5 V
VCS (T11-6) - E2S (T11-5)
4.5 to 5.5 V
|
|
||||
| OK | |
| 4. INSPECT NOZZLE VANE POSITION SENSOR |
![]() ![]() |
Turn the ignition switch ON.
Measure the voltage between the terminals of the turbo motor driver connector.
- Standard voltage:
Tester Connection
Specified Condition
VTA1 (T8-9) - VNE2 (T8-8)
0.5 to 4.5 V
VTA2 (T8-10) - E2S (T8-11)
0.5 to 4.5 V
Check the difference between the voltage values.
- Result:
- Voltage difference between VTA1 and VTA2 is within 0.8 V
|
|
||||
| OK | |
| 5. REPLACE TURBO MOTOR DRIVER |
| NEXT | |
| 6. CHECK WHETHER DTC OUTPUT RECURS (P2564, P2565, P2588 AND/OR P2589) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Perform the test drive.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Display (DTC output)
Proceed to
P2563, P2564, P2565, P2588 and/or P2589 is output again
A
No output
B
|
|
||||
| A | ||
| ||

