2014 Hilux · Service Manual BRAKE

Brake Warning Light does not Come ON

Circuit diagnosis · Vehicles built Nov 2011 – Mar 2012

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to Brake Warning Light Remains ON (Click here).

WIRING DIAGRAM

Refer to Brake Warning Light Remains ON (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK BRAKE WARNING LIGHT
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Turn the ignition switch to ON.

  1. Check that the brake warning light comes on.

    OK:
    The brake warning light comes on.

    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A


2. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER AND PARKING BRAKE SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the C25 combination meter connector.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-8 (BRL) - C25-26
    Always
    Below 1 Ω
    S35-8 (BRL) - Body ground
    Always
    10 kΩ or higher
    S35-29 (PKB) - P2-1
    Always
    Below 1 Ω
    S35-29 (PKB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Brake Warning Light
    Brake warning light
    Warning light ON / OFF
    Observe the combination meter.

  1. When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item / Range
    Normal Condition
    Diagnostic Note
    Brake Warning Light
    Brake warning light /
    ON or OFF
    ON: Brake warning light on
    OFF: Brake warning light off
    -
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display When Performing Active Test ON/OFF Operation
    ON
    Does not change between ON and OFF
    for LHD
    A
    Does not change between ON and OFF
    for RHD
    B
    Changes between ON and OFF
    C
    OFF
    Does not change between ON and OFF
    for LHD
    A
    Does not change between ON and OFF
    for RHD
    B
    Changes between ON and OFF
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← Brake Warning Light does not Come ON (Jun 2011 – Oct 2011)Brake Warning Light does not Come ON (Apr 2012 – Jul 2012) →