2014 Hilux · Service Manual HEATER & AIR CONDITIONING SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Jun 2011


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
E171001E03
  1. Disconnect the A44 air conditioning amplifier assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A44-1 (GND) - Body ground
    L - Body ground
    Ground
    Always
    Below 1 Ω
    A44-5 (+B1) - A44-1 (GND)
    L-Y - L
    Battery power source
    Always
    11 to 14 V
    A44-6 (IG+) - A44-1 (GND)
    R-L - L
    Ignition power source
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    A44-13 (MGC) - Body ground
    B - Body ground
    Magnet clutch signal
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    A44-14 (HR) - Body ground
    L-W - Body ground
    HTR relay signal
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the A44 air conditioning amplifier assembly connector.

  4. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A44-2 (BLW) - Body ground
    L-B - Body ground
    Blower motor speed control voltage
    1. Ignition switch ON
    2. Blower switch on (LO level)
    Pulse generation
    (See waveform 1)
    A44-3 (AOF) - A44-1 (GND)
    Y-B - L
    Mode damper servo operation voltage
    1. Ignition switch ON
    2. Mode switch DEF
    Below 1 V
    1. Ignition switch ON
    2. Mode switch FACE
    11 to 14 V
    A44-4 (AOD) - A44-1 (GND)
    R-B - L
    Mode damper servo operation voltage
    1. Ignition switch ON
    2. Mode switch FACE
    Below 1 V
    1. Ignition switch ON
    2. Mode switch DEF
    11 to 14 V
    A44-7 (ACT) - A44-1 (GND)
    R-L - L
    Magnet clutch on permit input signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on
    11 to 14 V
    A44-8 (TW) - A44-1 (GND)
    P - L
    Engine coolant temperature sensor signal
    Ignition switch ON
    Pulse generation
    A44-9 (SPD) - Body ground
    V-W - Body ground
    Vehicle speed signal
    Driving at approximately 20 km/h (12 mph)
    Pulse generation
    (See waveform 2)
    A44-13 (MGC) - Body ground
    B - Body ground
    Magnet clutch signal
    1. Engine idling
    2. A/C switch on
    Below 1 V
    1. Engine idling
    2. A/C switch off
    11 to 14 V
    A44-17 (AMH) - A44-1 (GND)
    L - L
    Air mix damper servo operation signal
    1. Ignition switch ON
    2. Temperature switch MAX HOT
    11 to 14 V
    1. Ignition switch ON
    2. Temperature switch MAX COLD
    Below 1 V
    A44-18 (TAMO) - A44-1 (GND)
    P - L
    Ambient temperature signal
    Ignition switch ON
    Pulse generation
    A44-19 (AMC) - A44-1 (GND)
    R-W - L
    Air mix damper servo operation signal
    1. Ignition switch ON
    2. Temperature switch MAX HOT
    Below 1 V
    1. Ignition switch ON
    2. Temperature switch MAX COLD
    11 to 14 V
    A44-21 (AC1) - A44-1 (GND)
    Y - L
    Idle-up request signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off or on (magnet clutch off)
    11 to 14 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on (magnet clutch on)
    Below 1 V
    A44-22 (AIR) - A44-1 (GND)
    L-W - L
    Recirculation damper servo operation voltage
    1. Ignition switch ON
    2. Fresh switch on
    Below 1 V
    1. Ignition switch ON
    2. Recirculation switch on
    11 to 14 V
    A44-23 (AIF) - A44-1 (GND)
    G-Y - L
    Recirculation damper servo operation voltage
    1. Ignition switch ON
    2. Recirculation switch on
    Below 1 V
    1. Ignition switch ON
    2. Fresh switch on
    11 to 14 V
    A46-1 (TE) - A46-14 (SG-4)
    G - P
    No. 1 cooler thermistor signal
    1. Ignition switch ON
    2. Evaporator temperature 0°C (32°F)
    2 to 2.4 V
    1. Ignition switch ON
    2. Evaporator temperature 15°C (59°F)
    1.4 to 1.8 V
    A46-2 (S5-3) - A44-1 (GND)
    W-R - L
    Power supply for solar sensor
    Ignition switch ON
    4.5 to 5.5 V
    A46-5 (PSW) - A44-1 (GND)
    Y-B - L
    Air conditioner pressure sensor signal
    1. Engine idling
    2. Refrigerant pressure normal
    Below 1 V
    1. Engine idling
    2. Refrigerant pressure less than 0.196 MPa (2.0 kgf/cm2, 28 psi) or more than 3.14 MPa (32.0 kgf/cm2, 455 psi)
    11 to 14 V
    A46-7 (TS) - A46-2 (S5-3)
    L-W - W-R
    Solar sensor signal
    1. Ignition switch ON
    2. Solar sensor subjected to electric light
    3. Vehicle indoors
    0.8 to 4.3 V
    1. Ignition switch ON
    2. Solar sensor covered with cloth
    3. Vehicle indoors
    Below 0.8 V
    A46-9 (VER) - Body ground*1
    R - Body ground
    Steering wheel location information signal
    Always
    Below 1 Ω
    A46-11 (SG-2) - Body ground
    L-Y - Body ground
    Ground for pulse position sensor (Mode damper servo)
    Always
    Below 1 Ω
    A46-13 (SG-3) - Body ground
    BR-Y - Body ground
    Ground for cooler thermistor
    Always
    Below 1 Ω
    A46-14 (SG-4) - Body ground
    P - Body ground
    Ground for No. 1 cooler thermistor
    Always
    Below 1 Ω
    A46-16 (PIB) - A46-21 (SG-7)
    R-L - LG-R
    Input signal for pulse position sensor (recirculation damper servo)
    1. Ignition switch ON
    2. Air inlet control recirculation to fresh or vice versa
    Pulse generation
    A46-17 (PIA) - A46-21 (SG-7)
    P-B - LG-R
    Input signal for pulse position sensor (recirculation damper servo)
    1. Ignition switch ON
    2. Air inlet control recirculation to fresh or vice versa
    Pulse generation
    A46-18 (TR) - A46-13 (SG-3)
    GR - BR-Y
    Cooler thermistor signal
    1. Ignition switch ON
    2. Cabin temperature 25°C (77°F)
    1.8 to 2.2 V
    1. Ignition switch ON
    2. Cabin temperature 40°C (104°F)
    1.2 to 1.6 V
    A46-20 (SG-1) - Body ground
    BR-Y - Body ground
    Ground for pulse position sensor (air mix damper servo)
    Always
    Below 1 V
    A46-21 (SG-7) - Body ground
    LG-R - Body ground
    Ground for pulse position sensor (recirculation damper servo)
    Always
    Below 1 Ω
    A46-23 (PMB) - A46-20 (SG-1)
    W-L - BR-Y
    Input signal for pulse position sensor (air mix damper servo)
    1. Ignition switch ON
    2. Temperature switch MAX HOT to MAX COLD
    Pulse generation
    A46-24 (PMA) - A46-20 (SG-1)
    W-R - BR-Y
    Input signal for pulse position sensor (air mix damper servo)
    1. Ignition switch ON
    2. Temperature switch MAX COLD to MAX HOT
    Pulse generation
    A46-25 (POB) - A46-11(SG-2)
    LG - L-Y
    Input signal for pulse position sensor (mode damper servo)
    1. Ignition switch ON
    2. Mode control FACE to DEF or vice versa
    Pulse generation
    A46-26 (POA) - A46-11 (SG-2)
    L-O - L-Y
    Input signal for pulse position sensor (mode damper servo)
    1. Ignition switch ON
    2. Mode control FACE to DEF or vice versa
    Pulse generation
    A43-3 (PTCR) - A44-1 (GND)*
    L-W - L
    Idle-up request signal for PTC heater
    1. Ignition switch ON
    2. Power heater switch off
    11 to 14 V
    1. Ignition switch ON
    2. Power heater switch on
    Below 1 V
    A44-11 (IGN) - A44-1 (GND)*2
    B-W - L
    Engine speed signal
    Engine idling
    Pulse generation
    A43-7 (TAIL) - A44-1 (GND)*2
    G - L
    Light control switch signal
    Light control switch OFF
    Below 1 V
    A43-6 (ALT) - A44-1 (GND)*2
    G - L
    Generator input signal
    Engine idling
    Pulse generation
    A43-1 (PTC1) - A44-1 (GND)*2
    R-W - L
    No. 1 PTC heater relay signal
    1. Engine idling
    2. Temperature switch MAX COLD to MAX HOT
    3. Coolant temperature 65°C (149°F) or less
    4. Ambient temperature 10°C (50°F) or less
    5. Headlight dimmer switch not in head position
    6. Generator is operating
    7. Blower switch on (Lo level)
    8. Heater switch assembly on
    11 to 14 V
    1. Engine idling
    2. Temperature switch MAX COLD to MAX HOT
    3. Coolant temperature 65°C (149°F) or less
    4. Ambient temperature 10°C (50°F) or less
    5. Headlight dimmer switch not in head position
    6. Generator is operating
    7. Blower switch on (Lo level)
    8. Heater switch assembly off
    Below 1 V
    A43-2 (PTC2) - A44-1 (GND)*2
    GR - L
    No. 2 PTC heater relay signal
    1. Engine idling
    2. Temperature switch MAX COLD to MAX HOT
    3. Coolant temperature 65°C (149°F) or less
    4. Ambient temperature 10°C (50°F) or less
    5. Headlight dimmer switch not in head position
    6. Generator is operating
    7. Blower switch on (Lo level)
    8. Heater switch assembly on
    11 to 14 V
    1. Engine idling
    2. Temperature switch MAX COLD to MAX HOT
    3. Coolant temperature 65°C (149°F) or less
    4. Ambient temperature 10°C (50°F) or less
    5. Headlight dimmer switch not in head position
    6. Generator is operating
    7. Blower switch on (Lo level)
    8. Heater switch assembly off
    Below 1 V
    A43-8 (HEAT) - A44-1 (GND)*2
    L-O - L
    Power heater switch input signal
    1. Ignition switch ON
    2. Power heater switch on
    Below 1 V
    1. Ignition switch ON
    2. Power heater switch off
    11 to 14 V
    A43-5 (SWIN) - A44-1 (GND)*2
    P - L
    Power heater switch indicator light signal
    1. Ignition switch ON
    2. Power heater switch on
    Below 1 V
    1. Ignition switch ON
    2. Power heater switch off
    11 to 14 V
    1. *1: for LHD
    2. *2: w/ PTC Heater
    3. If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.

  5. E171008E03
    Using an oscilloscope, check waveform 1.
    Blower motor control signal 
    Item
    Content
    Terminal No. (Symbol)
    A44-2 (BLW) - Body ground
    Tool Setting
    1 V/DIV., 50 μsec./DIV.
    Condition
    Ignition switch ON, Blower switch on (LO level)

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.

  6. E169152E02
    Using an oscilloscope, check waveform 2.
    Vehicle speed signal 
    Item
    Content
    Terminal No. (Symbol)
    A44-9 (SPD) - Body ground
    Tool Setting
    5 V/DIV., 20 ms./DIV.
    Condition
    Driving at approximately 20 km/h (12 mph)

    HINT:
    As the vehicle speed increases, the wavelength becomes shorter.


CHECK ECM (for 1GR-FE)
E127538E01
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E13-14 (THWO) - E17-1 (E1)
    P - BR
    Engine coolant temperature output signal
    Engine idling
    Pulse generation
    E13-24 (AC1) - E17-1 (E1)
    Y - BR
    Idle-up request signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on (magnet clutch on)
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off or on (magnet clutch off)
    11 to 14 V
    E13-25 (ACT) - E17-1 (E1)
    R-L - BR
    Magnet clutch on permit output signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on
    11 to 14 V
    E15-21 (THW) - E15-28 (E2)
    B - BR
    Engine coolant temperature sensor signal
    1. Engine idling
    2. Engine coolant temperature 20°C (68°F)
    0.2 to 1.0 V
    If the result is not as specified, the ECM may have a malfunction.


CHECK ECM (for 1KD-FTV, 2KD-FTV)
E170985E01
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E5-2 (THWO) - E7-7 (E1)
    P - BR
    Engine coolant temperature output signal
    Engine idling
    Pulse generation
    E6-18 (AC1) - E7-7 (E1)
    Y - BR
    Idle-up request signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on (magnet clutch on)
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off or on (magnet clutch off)
    11 to 14 V
    E6-19 (ACT) - E7-7 (E1)
    R-L - BR
    Magnet clutch on permit output signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on
    11 to 14 V
    E8-19 (THW) - E8-28 (E2)
    R-L - BR
    Engine coolant temperature sensor signal
    1. Engine idling
    2. Engine coolant temperature 20°C (68°F)
    0.2 to 1.0 V
    If the result is not as specified, the ECM may have a malfunction.


CHECK ECM (for 2TR-FE)
E170985E03
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E10-14 (THWO) - E12-3 (E1)
    P - BR
    Engine coolant temperature output signal
    Engine idling
    Pulse generation
    E10-24 (AC1) - E12-3 (E1)
    Y - BR
    Idle-up request signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on (magnet clutch on)
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off or on (magnet clutch off)
    11 to 14 V
    E10-25 (ACT) - E12-3 (E1)
    R-L - BR
    Magnet clutch on permit output signal
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch off
    Below 1 V
    1. Engine idling
    2. Blower switch on (LO level)
    3. A/C switch on
    11 to 14 V
    E12-32 (THW) - E12-28 (E2)
    B - BR
    Engine coolant temperature sensor signal
    1. Engine idling
    2. Engine coolant temperature 20°C (68°F)
    0.2 to 1.0 V
    If the result is not as specified, the ECM may have a malfunction.


CHECK ACCESSORY METER ASSEMBLY
E165586E03
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A27-3 (TH+) - A27-2 (SG)
    W-G - BR-Y*1
    L - BR*2
    W-G - BR-Y*3
    Ambient temperature sensor signal
    1. Ignition switch ON
    2. Ambient temperature 20 to 30°C (68 to 86°F)
    1 to 1.6 V
    Ambient temperature sensor signal
    1. Ignition switch ON
    2. Ambient temperature 30 to 50°C (86 to 122°F)
    0.6 to 1 V
    A27-9 (DATA) - A27-1 (GND1)
    P - LG
    Ambient temperature sensor signal
    Ignition switch ON
    Pulse generation
    1. *1: for Europe, w/ Light Control Rheostat
    2. *2: for Europe, w/o Light Control Rheostat
    3. *3: except Europe
    4. If the result is not as specified, the accessory meter assembly may have a malfunction.


CHECK COMBINATION METER ASSEMBLY
E165587E02
  1. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    C8-6 - C8-22
    V-R - Y
    Vehicle speed signal
    Driving at approximately 20 km/h (12 mph)
    Pulse generation
    (See waveform)
    1. If the result is not as specified, the combination meter assembly may have a malfunction.

  2. E169152E02
    Using an oscilloscope, check waveform 1.
    Vehicle speed signal 
    Item
    Content
    Terminal No. (Symbol)
    C8-6 - C8-22
    Tool Setting
    5 V/DIV., 20 ms./DIV.
    Condition
    Driving at approximately 20 km/h (12 mph)

    HINT:
    When the blower level is increased, the duty ratio changes accordingly.

← PROBLEM SYMPTOMS TABLE (from Aug 2013)DIAGNOSIS SYSTEM (from Jun 2011) →