P011C Charge Air Temperature/Intake Air Temperature Correlation (Bank 1)
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTC P007C (Click here).Refer to DTC P0112 (Click here).
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| After engine completely warmed up, allow engine to soak for long time (10 hours or more). Start the engine and idle the engine for 3 minutes or more. |
After the engine is completely warmed up and then allowed to soak for a long time (10 hours or more), the difference in temperature at the intake air temperature sensor and intake air temperature sensor (turbo) after turbocharger after idling for 3 minutes is 15°C (59°F) or higher. (2 trip detection logic) |
|
| DTC No. |
Data List |
| P011C |
|
WIRING DIAGRAM
Refer to DTC P007C (Click here).Refer to DTC P0112 (Click here).
INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P011C) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P011C is output
A
P011C and other DTCs are output
B
|
|
||||
| A | |
| 2. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE) |
Allow the engine to soak for 1 to 2 hours.
- HINT:
- It is not necessary to allow the engine to soak if the engine is cold.
- The engine cools faster if the hood is opened.
- It is not necessary to allow the engine to soak if the engine is cold.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
Read the value.
- OK:
- The difference between the displayed value and outside air temperature is below 5°C (9°F).
- NOTICE:
- If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
| NEXT | |
| 3. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.
Read the value.
- OK:
- The difference between the displayed value and outside air temperature is below 15°C (27°F).
|
|
||||
| OK | |
| 4. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE (TURBO)) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
Read the value.
- OK:
- The difference between the displayed value and outside air temperature is below 15°C (27°F).
|
|
||||
| OK | |
| 5. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM) |
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A40-1 (THA) - E26-6 (THA)
Always
Below 1 Ω
A40-2 (E2) - E27-14 (E2)
Always
Below 1 Ω
A40-1 (THA) or E26-6 (THA) - Body ground
Always
10 kΩ or higher
Reconnect the mass air flow meter connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 7. REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
- HINT:
- If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.
|
|
||||
| 8. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM) |
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
I4-2 - E26-3 (THIA)
Always
Below 1 Ω
I4-1 - E27-14 (E2)
Always
Below 1 Ω
I4-2 or E26-3 (THIA) - Body ground
Always
10 kΩ or higher
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 9. REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO) |
Replace the intake air temperature sensor (turbo) (Click here).
|
|
||||
| 10. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Allow the engine to soak for 1 to 2 hours.
- HINT:
- It is not necessary to allow the engine to soak if the engine is cold.
- The engine cools faster if the hood is opened.
- It is not necessary to allow the engine to soak if the engine is cold.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant temp.
Read the value.
- NOTICE:
- If the difference between "Coolant Temp" and the outside air temperature is 5°C (9°F) or higher, the heat from the engine affects the intake air temperature sensor, causing an incorrect value to be displayed. In this case, allow the engine to soak again.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air and Intake Air Temp (Turbo).
Read the value.
- OK:
- The difference between the displayed value and outside air temperature is below 15°C (27°F).
| NEXT | ||
| ||
