2014 Hilux · Service Manual BODY ELECTRICAL

INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT STEERING PAD SWITCH LH (w/o Multi-information Display)

  1. Measure the resistance according to the value(s) in the table below.

    C238704E01

    Text in Illustration 
    *1
    Volume+ Switch
    *2
    Volume- Switch
    *3
    Seek+ Switch
    *4
    Seek- Switch
    *5
    MODE Switch
    *6
    Horn Wire

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    9 (AU2) - 8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    10 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    10 (AU1) - 8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    10 (AU1) - 8 (EAU)
    Seek- switch pushed
    312.6 to 345.5 Ω
    10 (AU1) - 8 (EAU)
    Volume+ switch pushed
    950 to 1050 Ω
    10 (AU1) - 8 (EAU)
    Volume- switch pushed
    2954.5 to 3265.5 Ω
    1 (HO) - Horn wire
    Always
    Below 2.5 Ω

    If the result is not as specified, replace the steering pad switch assembly.

  1. Check the illumination.

    1. Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.

    2. Check that the switch illumination comes on.

      OK:
      Steering pad switch illumination comes on.

      If the result is not as specified, replace the steering pad switch assembly.


INSPECT STEERING PAD SWITCH ASSEMBLY (w/ Multi-information Display)

  1. Measure the resistance according to the value(s) in the table below.

    C238003E01

    Text in Illustration 
    *1
    Volume+ Switch
    *2
    Volume- Switch
    *3
    Seek+ Switch
    *4
    Seek- Switch
    *5
    MODE Switch
    *6
    On Hook Switch
    *7
    Off Hook Switch
    *8
    DISP Switch
    *9
    Horn Wire
    -
    -

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    9 (AU2) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    9 (AU2) - 8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    9 (AU2) - 8 (EAU)
    On hook switch pushed
    312.6 to 345.5 Ω
    9 (AU2) - 8 (EAU)
    Off hook switch pushed
    950 to 1050 Ω
    10 (AU1) - 8 (EAU)
    No switch pushed
    95 to 105 kΩ
    10 (AU1) - 8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    10 (AU1) - 8 (EAU)
    Seek- switch pushed
    312.6 to 345.5 Ω
    10 (AU1) - 8 (EAU)
    Volume+ switch pushed
    950 to 1050 Ω
    10 (AU1) - 8 (EAU)
    Volume- switch pushed
    2954.5 to 3265.5 Ω
    7 (DISP) - 8 (EAU)
    DISP switch pushed
    Below 2.5 Ω
    1 (HO) - Horn wire
    Always
    Below 2.5 Ω

    If the result is not as specified, replace the steering pad switch assembly.

  1. Connect the battery positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch assembly connector.

  1. Check that the switch illumination comes on.

    OK:
    Steering pad switch illumination comes on.

    If the result is not as specified, replace the steering pad switch assembly.

← REMOVAL (from Aug 2013)INSTALLATION (Jun 2011 – Jul 2012) →