2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER
(Click here)

3. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A252273
    Remove the bolt, nut and 2 No. 2 injection pipe clamps.

  1. A252274
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


4. DISCONNECT WIRING HARNESS CLAMP BRACKET

5. REMOVE NO. 2 FUEL PIPE

  1. A252279
    Using a 6 mm hexagon wrench, remove the supply pump hollow screw and gasket.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Supply Pump Hollow Screw
    V100137
    Fuel Check Valve
    V100138
    Union Bolt

  1. Remove the fuel check valve, union bolt and 2 gaskets.

  1. Remove the 3 bolts and No. 2 fuel pipe.


6. REMOVE NO. 3 NOZZLE LEAKAGE PIPE

  1. A252280
    Disconnect the 3 fuel hoses.
    Text in Illustration 
    V100136
    Fuel Check Valve

  1. Remove the 2 bolts.

  1. Remove the fuel check valve, gasket and No. 3 nozzle leakage pipe.


7. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A252281
    Remove the 2 bolts.
    Text in Illustration 
    V100136
    Union Bolt

  1. Remove the union bolt, gasket and No. 2 nozzle leakage pipe.


8. REMOVE GLOW CONNECTOR BRACKET

A253492
  1. Disconnect the No. 1 glow plug connector and detach the clamp.

  1. A254198
    Remove the bolt and glow connector bracket.


9. REMOVE NO. 3 INTERCOOLER SUPPORT BRACKET

  1. A254004
    Remove the bolt and No. 3 intercooler support bracket.


10. REMOVE NO. 2 MANIFOLD STAY

  1. A245458
    Remove the bolt and No. 2 manifold stay.


11. REMOVE NO. 1 GLOW PLUG CONNECTOR
  1. Disconnect the No. 1 glow plug connector from the wire harness.

  1. A247184
    Remove the 4 screw grommets.

  1. A247185
    Remove the 4 nuts and No. 1 glow plug connector.


12. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR

A256544

13. REMOVE INTAKE MANIFOLD INSULATOR

  1. A245459
    Remove the intake manifold insulator.


14. REMOVE INTAKE MANIFOLD
  1. Remove the bolt and disconnect the fuel hose protector from the intake manifold.

  1. A245461
    Detach the sensor wire connector clamp from the intake manifold.

  1. A254200
    Remove the 4 bolts, 2 nuts, intake manifold and gasket.

← REMOVAL (Aug 2012 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →