INSTALLATION
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
- NOTICE:
- When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
- When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
- After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.
- When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
| 1. INSTALL INJECTOR ASSEMBLY |
- NOTICE:
- Be sure to install each injector, No. 1 nozzle holder clamp, washer and bolt in its original position.
Install 4 new injection nozzle seats to the cylinder head.

Apply a small amount of clean engine oil to 4 new O-rings.
Install one of the O-rings to each injector as shown in the illustration.

Text in Illustration *1
New O-Ring
Insert the 4 injectors into the cylinder head.
- NOTICE:
- Insert the injector until it touches the injection nozzle seat surface.
- After installing the injector to the cylinder head, the O-ring may prevent the injector from being fully seated. If so, pull out the injector and reinstall it.
- Always reinstall an injector to the same place it was removed from.
- Insert the injector until it touches the injection nozzle seat surface.
For an injector that has been replaced with a new injector, register the injector compensation code (Click here).
Temporarily install 4 new washers and the 4 No. 1 nozzle holder clamps with the 4 bolts.

Text in Illustration *1
Washer
*a
Downward
- NOTICE:
-


- The fork portion of the No. 1 nozzle holder clamp must be set on the injector.
- Before tightening the bolts, check that the No. 1 nozzle holder clamps are set properly.
- When installing the clamp bolts, first tighten them by hand until they cannot be turned further. Then, tighten the bolts to the specified torque in a following step.
- When tightening the bolts, be careful so as not to tilt the bolt or clamp.
- Do not reuse the washer.
- The fork portion of the No. 1 nozzle holder clamp must be set on the injector.
Text in Illustration *1
No. 1 Nozzle Holder Clamp
- HINT:
- Apply a small amount of engine oil to the threads and under the heads of the clamp bolts.
Temporarily install the 4 injection pipes with the union nuts.
- HINT:
- To position the injectors, loosely tighten the union nuts.
Check the nozzle leakage pipe. Check that there are no scratches or dents on the 5 union seal surfaces.

If scratches or dents are present, replace the nozzle leakage pipe.
Set the nozzle leakage pipe and 5 new gaskets in place.

Text in Illustration *1
Union Bolt
Apply a small amount of oil to the 4 injector hollow screws and union bolt.
Temporarily install the nozzle leakage pipe with the 4 injector hollow screws and union bolt.
Tighten the 4 nozzle holder clamp bolts.
- Torque:
- 22 N*m{ 220 kgf*cm , 16 ft.*lbf }
Remove the 4 injection pipes.
Tighten the 4 injector hollow screws in order from 1 to 4.

- Torque:
- 16 N*m{ 163 kgf*cm , 12 ft.*lbf }
Text in Illustration *1
Union Bolt
- NOTICE:
- If an injector hollow screw is accidentally tightened beyond the torque specification, it must be replaced.
Tighten the union bolt.
- Torque:
- 13 N*m{ 127 kgf*cm , 9 ft.*lbf }
- NOTICE:
- If the union bolt is accidentally tightened beyond the torque specification, it must be replaced.
| 2. INSPECT FOR FUEL LEAK |
Check that there are no leaks from the nozzle leakage pipe connection.

Install a new gasket and the No. 2 nozzle leakage pipe to the cylinder head with SST (check valve).
- Part No.:
- 23762-27010 (No. 2 nozzle leakage pipe)
90904-30012 (Gasket)
- SST
- 09280-00010
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Apply a small amount of soapy water (or other fluid for detecting fuel leakage) on the nozzle leakage pipe connection.
Install SST (turbocharger pressure gauge) to the fuel return side of the nozzle leakage pipe, maintain 100 kPa (1.0 kgf/cm2, 15 psi) of pressure for 60 seconds and check that no bubbles form.

- SST
- 09992-00242
After checking for fuel leaks, wipe off the soapy water from the nozzle leakage pipe connection.
Remove SST, the No. 2 nozzle leakage pipe and gasket.
- NOTICE:
- Never reinstall the disassembled union bolt to the engine.
| 3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Install 4 new No. 3 cylinder head cover gaskets to the cylinder head cover in the directions shown in the illustration.

Text in Illustration *1
No. 3 Cylinder Head Cover Gasket
*2
Cylinder Head Cover
- NOTICE:
- Do not install the No. 3 cylinder head cover gaskets at an angle.
- Check that there is no foreign matter at the installation location of the No. 3 cylinder head cover gaskets.
- Do not install the No. 3 cylinder head cover gaskets at an angle.
Remove any old seal packing (FIPG material) from the cylinder head.
Apply seal packing to the areas shown in the illustration.

- Seal packing:
- Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Text in Illustration 

Seal Packing
- NOTICE:
- Remove any oil from the contact surface.
- Install the cylinder head cover within 3 minutes after applying seal packing.
- Do not start the engine for at least 2 hours after installing the cylinder head cover.
- Remove any oil from the contact surface.
Install a new cylinder head cover gasket to the cylinder head cover.
Temporarily install the cylinder head cover with the 10 bolts and 2 nuts in the order shown in the illustration. Then, tighten the 10 bolts and 2 nuts in the order shown in the illustration in 2 progressive steps.

- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
Connect the ventilation hose.
Install 4 new nozzle holder seals.
| 4. INSTALL NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY |
Install the No. 2 cylinder head cover with the 3 bolts.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
| 5. INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Temporarily install the No. 2 nozzle leakage pipe with the 2 bolts.

Text in Illustration 

Union Bolt
Temporarily install a new gasket and the union bolt.
Tighten the 2 bolts and union bolt.
- Torque:
- for bolt A:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
- for bolt B:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
- for union bolt:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
| 6. INSTALL NO. 3 NOZZLE LEAKAGE PIPE |
Apply a light coat of fuel to the O-ring of the fuel check valve.

Text in Illustration *1
O-Ring
Temporarily install the No. 3 nozzle leakage pipe with the 2 bolts.

Text in Illustration 

Fuel Check Valve
Temporarily install a new gasket and the fuel check valve.
Tighten the 2 bolts and fuel check valve.
- Torque:
- for bolt:
- 13 N*m{ 130 kgf*cm , 9 ft.*lbf }
- for fuel check valve:
- 32 N*m{ 321 kgf*cm , 23 ft.*lbf }
Connect the 3 fuel hoses.
| 7. INSTALL NO. 2 FUEL PIPE |
Apply a light coat of fuel to the O-ring of the fuel check valve.

Text in Illustration *1
O-Ring
Temporarily install the No. 2 fuel pipe with the 3 bolts.

Text in Illustration *1
Gasket
*2
No. 1 Fuel Pipe


Bolt


Supply Pump Hollow Screw


Fuel Check Valve


Union Bolt
Install a new gasket to the No. 1 fuel pipe and temporarily install the union bolt.
Temporarily install a new gasket and the fuel check valve.
- NOTICE:
- When temporarily installing the fuel check valve, position the gasket as shown in the illustration.
Temporarily install a new gasket and the supply pump hollow screw.
Using a 6 mm hexagon wrench, tighten the supply pump hollow screw.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
Tighten the 3 bolts, fuel check valve and union bolt.
- Torque:
- for bolt:
- 20 N*m{ 204 kgf*cm , 15 ft.*lbf }
- for fuel check valve:
- 32 N*m{ 321 kgf*cm , 23 ft.*lbf }
- for union bolt:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
- NOTICE:
- When tightening the fuel check valve, replace the gasket if it becomes deformed.
Connect the vacuum switching valve connector and 2 vacuum transmitting hoses.

Text in Illustration *1
Paint Mark
- HINT:
- When connecting the vacuum transmitting hoses, connect the hose that has the paint mark to the port labeled A in the illustration.
| 8. INSTALL WIRING HARNESS CLAMP BRACKET |
Install the wiring harness clamp bracket with the bolt.
- Torque:
- 13 N*m{ 128 kgf*cm , 9 ft.*lbf }
Attach the wire harness clamp.
| 9. INSTALL NO. 4 INJECTION PIPE SUB-ASSEMBLY |
- NOTICE:
- When replacing an injector, it is necessary to replace the 4 injection pipes with new ones.
- Keep the joints of the injection pipe clean.
- When replacing an injector, it is necessary to replace the 4 injection pipes with new ones.
Temporarily install the No. 4 injection pipe with the union nuts.
Install the 2 No. 2 injection pipe clamps with the bolt and nut.
- Torque:
- 5.0 N*m{ 51 kgf*cm , 44 in.*lbf }
Using a 17 mm union nut wrench, tighten the injection pipe union nut on the common rail side.
- Torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
Using a 17 mm union nut wrench, tighten the injection pipe union nuts on the injector side.
- Torque:
- 35 N*m{ 357 kgf*cm , 26 ft.*lbf }
- NOTICE:
- Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).
| 10. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER |
| 11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 12. ADD ENGINE COOLANT |
Tighten the cylinder block drain cock plug.
- Torque:
- 8.0 N*m{ 82 kgf*cm , 71 in.*lbf }
Tighten the radiator drain cock plug by hand.
Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

- Standard capacity:
Item
Specified Condition
A/T
11.1 liters (11.7 US qts, 9.8 Imp. qts)
M/T
9.8 liters (10.4 US qts, 8.6 Imp. qts)
- HINT:
- TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
- NOTICE:
- Never use water as a substitute for engine coolant.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the B line, add TOYOTA SLLC to the B line.
Install the radiator reservoir cap.
Using a wrench, install the vent plug.

- Torque:
- 2.0 N*m{ 20 kgf*cm , 18 in.*lbf }
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
- HINT:
- The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.
Maintain the engine speed at 2500 to 3000 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
- CAUTION:
- When pressing the radiator hoses:
- Wear protective gloves.
- Be careful as the radiator hoses are hot.
- Keep your hands away from the radiator fan.
- Wear protective gloves.
Stop the engine and wait until the coolant cools down to ambient temperature.
- CAUTION:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
After the coolant cools down, check that the coolant level is at the F line.

If the coolant level is below the F line, add TOYOTA SLLC to the F line.
| 13. BLEED AIR FROM FUEL SYSTEM |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

- NOTICE:
- Hand pump pumping speed: Max. 2 strokes/ sec.
- The hand pump must be pushed with a full stroke during pumping.
- When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.
- If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.
- If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.
- If air bleeding using the hand pump is incomplete, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.
- Hand pump pumping speed: Max. 2 strokes/ sec.
Check if the engine starts.
- NOTICE:
- Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
- Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.
- Use a fully-charged battery.
- Even if air bleeding using the hand pump has been completed, the starter may need to be cranked for 10 seconds or more to start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2

Text in Illustration *a
Reference
(Active Test Operation)
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.


- HINT:
- When the Active Test "Test the Fuel Leak" is used to change the pump control mode, the actual fuel pressure inside the common rail drops below the target fuel pressure when the Active Test is off, but this is normal and does not indicate a pump malfunction.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
- HINT:
- It is necessary to clear the DTCs, as DTC P1604 or P1605 may be stored when air is bled from the fuel system after replacing or repairing fuel system parts.
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
- OK:
- No DTCs are output.
| 14. PERFORM REGISTRATION |
Perform registration of the injector compensation codes (Click here).
Perform pilot quantity learning (Click here).
| 15. INSPECT FOR COOLANT LEAK |
- NOTICE:
- Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Fill the radiator with coolant and attach a radiator cap tester to the radiator reservoir.

Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17.1 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks.
If no external leaks are found, check the cylinder block and head.
| 16. INSPECT FOR FUEL LEAK |
Perform the Active Test.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Test.
Intelligent Tester Display
Test Part
Control Range
Diagnostic Note
Test the Fuel Leak
Pressurize common rail interior and check for fuel leaks
Stop/Start
- The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.
- The above conditions are maintained while the Active Test is being performed.
- The fuel pressure inside the common rail increases to the specified value and the engine speed increases to 2000 rpm when the Active Test is performed.
| 17. INSPECT FOR OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the areas that were worked on.
| 18. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
If low, check for leakage and add oil up to the full level mark.- NOTICE:
- Do not fill engine oil above the full level mark.
