2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011


1. REMOVE TAILPIPE ASSEMBLY
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the tailpipe from the center exhaust pipe and remove the gasket.

  1. Remove the tailpipe from the exhaust pipe support.


2. REMOVE CENTER EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the gasket.


3. REMOVE NO. 2 ENGINE UNDER COVER

4. SUPPORT TRANSMISSION AND TRANSFER ASSEMBLY

  1. C111233
    Support the transmission and transfer with a transmission jack.


5. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034218E03
  1. Support the transmission rear side with a support stand.

  1. Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. Remove the 4 bolts, 4 nuts and frame crossmember.


6. REMOVE NO. 2 EXHAUST PIPE SUPPORT BRACKET

  1. A254003
    Remove the 2 bolts and No. 2 exhaust pipe support bracket from the No. 3 frame crossmember.


7. REMOVE AIR FUEL RATIO SENSOR

A254444E01
  1. for 4WD:
    Disconnect the air fuel ratio sensor connector.

  1. for Pre-Runner:
    Disconnect the air fuel ratio sensor connector and detach the clamp.

    Text in Illustration 
    *A
    for 4WD
    *B
    for Pre-Runner

  1. A253514E01
    Using SST, remove the air fuel ratio sensor from the front exhaust pipe.
    SST
    09224-00010  


8. REMOVE FRONT EXHAUST PIPE ASSEMBLY

  1. A253992
    Disconnect the exhaust gas temperature sensor connector and detach the clamp.

  1. A253993
    Disconnect the No. 2 exhaust gas temperature sensor connector.

  1. A253996E01
    Disconnect the No. 3 exhaust gas temperature sensor connector and detach the clamp.
    Text in Illustration 
    *A
    for 4WD
    *B
    for 2WD

  1. A253997
    Disconnect the No. 6 exhaust pipe air hose and No. 7 exhaust pipe air hose from the front exhaust pipe.

  1. A253999
    Remove the 2 exhaust pipe supports.

  1. A253998
    Remove the 3 nuts and front exhaust pipe.

  1. Remove the gasket.


9. REMOVE EXHAUST GAS TEMPERATURE SENSOR

A253518

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Using a 14 mm union nut wrench, remove the exhaust gas temperature sensor.


10. REMOVE NO. 2 EXHAUST GAS TEMPERATURE SENSOR

A254000

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Detach the 5 clamps.

  1. Using a 14 mm union nut wrench, remove the No. 2 exhaust gas temperature sensor.


11. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A254002
    Remove the bolt and wiring harness clamp bracket.


12. REMOVE NO. 3 EXHAUST GAS TEMPERATURE SENSOR

A253520

NOTICE:
If the sensor is dropped, replace it with a new one.

  1. Using a 14 mm union nut wrench, remove the No. 3 exhaust gas temperature sensor.


13. REMOVE EXHAUST PIPE CLAMP SUB-ASSEMBLY

  1. A254001
    Remove the bolt, nut and exhaust pipe clamp.


14. REMOVE MONOLITHIC CONVERTER PROTECTOR

  1. A254672
    Remove the 4 bolts and 4 nuts.

  1. A254673E01
    Remove the upper monolithic converter protector and lower monolithic converter protector.
    Text in Illustration 
    *1
    Upper Monolithic Converter Protector
    *2
    Lower Monolithic Converter Protector


15. REMOVE CONVERTER PROTECTOR STAY

  1. A254674E01
    Remove the 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.
    Text in Illustration 
    *1
    No. 1 Converter Protector Stay
    *2
    No. 2 Converter Protector Stay

← COMPONENTS (from Jun 2011)INSTALLATION (from Jun 2011) →