CUSTOMIZE PARAMETERS
Removal / installation · Vehicles built from Jun 2011
| 1. CUSTOMIZE POWER DOOR LOCK CONTROL SYSTEM |
- HINT:
- The following items can be customized.
- During customize mode, the alarm control functions are disabled.
- During customize mode, the following wireless control functions are disabled: remote alarm function, automatic locking function, operation stop function and illuminated entry function.
- During customize mode, the ECU will not output lock/unlock signals.
- While in customize mode, if the key is inserted into the ignition key cylinder or a door is opened, customize mode will be canceled.
- The following items can be customized.
- NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Record the current settings before customizing.
- When the customer requests a change in a function, first make sure that the function can be customized.
Customizing with manual operation
Display
Default
Content
Setting
Relevant ECU
Speed-sensitive automatic door lock function (for LHD)
ON
Function that locks all doors once vehicle speed reaches 25 km/h (16 mph) for 1 second or more
ON or OFF*
Theft warning ECU assembly
Ignition switch-linked automatic door unlock function (for LHD)
ON
After speed-sensitive automatic door lock function operates, turning ignition switch OFF causes doors to automatically unlock
ON or OFF*
Theft warning ECU assembly
2 step unlock function
ON
- Driver side door can be unlocked by pressing transmitter's unlock switch once; remaining doors can be unlocked by pressing transmitter's unlock switch a second time.
- Driver side door can be unlocked by turning door key cylinder once; remaining doors can be unlocked by turning door key cylinder a second time.
ON or OFF*
Theft warning ECU assembly
- *: When customizing the ON/OFF setting of the speed-sensitive automatic door lock function (for LHD), ignition switch-linked automatic door unlock function (for LHD) or 2 step unlock function, please note that the two functions' settings are synchronized. For information on how to customize, refer to the flowchart below.
Check that the following conditions are met.
- No key is in the ignition key cylinder.
- The theft deterrent system is in the disarmed state (when either condition below is met):
- All the doors are in the unlocked condition and the doors are locked and unlocked using the door control transmitter.
- The key is inserted into the ignition key cylinder, the ignition switch is turned to ON then off, and then the key is removed.
- The driver side door is opened (the other doors are closed).
- No key is in the ignition key cylinder.
Perform the following operation twice within 5 seconds:
- Insert the key into the ignition key cylinder, and then pull it out (ending with the key pulled out).
- Insert the key into the ignition key cylinder, and then pull it out (ending with the key pulled out).
Wait for 5 seconds.
After completing the above step, press and hold down lock switch and unlock switch on the door control transmitter at the same time for over 3 seconds within 5 seconds.
Check that the hazard warning lights flash once.
After completing the lock and unlock switch operation, perform the following operation within 5 seconds.
- Press the lock switch twice (Speed-sensitive automatic door lock function and ignition switch-linked automatic door unlock function [for LHD]) or 3 times (2 step unlock function) within 2seconds.
- Press the lock switch twice (Speed-sensitive automatic door lock function and ignition switch-linked automatic door unlock function [for LHD]) or 3 times (2 step unlock function) within 2seconds.
After completing the above step, press the unlock switch on door control transmitter once within 2 seconds.
Check that the hazard warning lights flash twice (Speed-sensitive automatic door lock function and ignition switch-linked automatic door unlock function [for LHD]) or 3 times (2 step unlock function).
After completing the unlock switch operation, perform the following operations (mode select) within 10 seconds:
- Press the lock switch on door control transmitter the number of times shown below depending on the desired function behavior to select the answer-back pattern and warning function setting. Press the unlock switch on door lock transmitter once within 2 seconds of pressing the lock switch on door control transmitter.
- Speed-sensitive automatic door lock function (for LHD): ON
Ignition switch-linked automatic door unlock function (for LHD): ON
2 step unlock function: ON
- Press the lock switch on door control transmitter once.
- Speed-sensitive automatic door lock function (for LHD): OFF
Ignition switch-linked automatic door unlock function (for LHD): OFF
2 step unlock function: OFF
- Press the lock switch on door control transmitter twice.
- Speed-sensitive automatic door lock function (for LHD): Canceled
Ignition switch-linked automatic door unlock function (for LHD): Canceled
2 step unlock function: Canceled
- Press the lock switch on door control transmitter 3 times or more.
Pattern 1Pattern 2Pattern 3- Press the lock switch on door control transmitter the number of times shown below depending on the desired function behavior to select the answer-back pattern and warning function setting. Press the unlock switch on door lock transmitter once within 2 seconds of pressing the lock switch on door control transmitter.
Check the response to the customize operation.
Response to Customize Operation
Setting
Speed-sensitive Automatic Door Lock Function (for LHD)
Ignition Switch-linked Automatic Door Unlock Function (for LHD)
2 Step Unlock Function
Hazard warning lights flash once
ON
ON
ON
Hazard warning lights flash twice
OFF
OFF
OFF
- Driver side door can be unlocked by pressing transmitter's unlock switch once; remaining doors can be unlocked by pressing transmitter's unlock switch a second time.
