2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE DIESEL THROTTLE BODY ASSEMBLY
(Click here)

3. REMOVE NO. 1 ENGINE UNDER COVER

4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


5. REMOVE FRONT WHEEL LH

6. REMOVE FRONT FENDER APRON SEAL UPPER
  1. Remove the 5 clips and front fender apron seal upper.


7. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and front fender seal.


8. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.

  1. A252236
    Detach the wire harness clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring from the engine oil level dipstick guide.


9. DISCONNECT WATER BY-PASS HOSE

  1. Disconnect the 6 water by-pass hoses.

    A252237


10. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE
  1. Disconnect the vacuum switching valve connector.

  1. Disconnect the 2 vacuum transmitting hoses.

  1. A252239
    Remove the 2 bolts and manifold stay with vacuum switching valve.


11. REMOVE NO. 3 CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A252240
    Remove the 3 bolts and No. 3 cylinder head cover.


12. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A252241
    Remove the bolt and No. 2 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


13. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A252242
    Disconnect the 4 injector connectors and electric EGR control valve connector.

  1. Detach the 2 wire harness clamps.

  1. A252243
    Remove the 4 nuts and 2 No. 3 injection pipe clamps.

  1. A252244E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side


14. REMOVE NO. 5 WATER BY-PASS PIPE

  1. A252245
    Detach the 2 wire harness clamps.

  1. A252246
    Disconnect the 2 water hoses from the electric EGR control valve.

  1. Remove the 2 bolts and No. 5 water by-pass pipe.


15. REMOVE MANIFOLD ABSOLUTE PRESSURE SENSOR

  1. A252248
    Disconnect the manifold absolute pressure sensor connector and vacuum hose.

  1. Remove the bolt and manifold absolute pressure sensor.


16. REMOVE GAS FILTER BRACKET WITH GAS FILTER

  1. A252249
    Disconnect the vacuum hose.

  1. Remove the bolt and gas filter bracket with gas filter.


17. REMOVE WIRING HARNESS CLAMP BRACKET

  1. A252250
    Remove the bolt and wiring harness clamp bracket.


18. REMOVE THROTTLE BODY BRACKET

  1. A252251
    Remove the 3 bolts and throttle body bracket.


19. DISCONNECT ENGINE WIRE

  1. A252252
    Detach the 2 wire harness clamps.

  1. Remove the bolt and disconnect the engine wire.


20. DISCONNECT NO. 3 WATER BY-PASS PIPE

  1. A252253
    Remove the 2 bolts and disconnect the No. 3 water by-pass pipe.


21. REMOVE EGR VALVE BRACKET

  1. A252254
    Remove the 3 bolts and EGR valve bracket.


22. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

  1. A252255
    Disconnect the fuel pressure sensor connector from the common rail.

  1. Remove the 5 bolts, 2 nuts and electric EGR control valve with No. 2 EGR valve and EGR cooler.

    A252256E01

    Text in Illustration 
    *1
    Gasket
    -
    -

  1. Remove the 2 gaskets from the cylinder head and intake manifold.


23. REMOVE INTAKE AIR CONNECTOR WITH ELECTRIC EGR CONTROL VALVE ASSEMBLY

  1. A252257
    Remove the 3 nuts, intake air connector with electric EGR control valve and gasket.


24. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Remove the electric EGR control valve and gasket from the intake air connector.


25. REMOVE EGR VALVE ADAPTER

  1. A252258
    Using a 6 mm hexagon wrench, remove the 3 hexagon socket head cap bolts, 3 plate washers, EGR valve adapter and gasket.


26. REMOVE NO. 2 EGR VALVE ASSEMBLY

  1. A252259
    Remove the bolt, No. 2 EGR valve and gasket.


27. REMOVE EGR COOLER INSULATOR

  1. A252260E01
    Remove the 2 EGR cooler insulators from the EGR cooler.
    Text in Illustration 
    *1
    No. 2 EGR Cooler Insulator
    *2
    No. 1 EGR Cooler Insulator

← REMOVAL (Aug 2012 – Jul 2013)INSPECTION (from Jun 2011) →