2014 Hilux · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.
  3. Use the same procedure for the RH and LH sides.
  4. The procedure listed below is for the LH side.


1. PRECAUTION (w/ Power Window)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Power Window)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL (w/ Power Window)

  1. B277098
    Using a moulding remover, detach the 2 clips and 2 claws and remove the rear power window regulator switch assembly with rear door armrest base panel.

  1. Disconnect the connector.


4. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

  1. B277021E01
    Insert a clip remover between the plate and trim board.

    HINT:
    Tape the clip remover tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Turn the handle clockwise to remove the snap ring, rear door window regulator handle and plate.


5. REMOVE DOOR PULL HANDLE

  1. B277099
    Remove the screw and door pull handle.


6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B277100
    Remove the clip and screw.

  1. Detach the 9 clips and remove the rear door trim board.


7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH

  1. B277134
    Raise the 6 claws of the rear door inner glass weatherstrip as shown in the illustration, and then remove the rear door inner glass weatherstrip from the rear door trim board.


8. REMOVE REAR DOOR OUTER GLASS WEATHERSTRIP LH

  1. B278870E01
    Put protective tape around the rear door outer glass weatherstrip.
    Text in Illustration 
    *1
    Protective Tape

  1. Detach the 4 claws and remove the rear door outer glass weatherstrip.


9. REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

  1. E233203E01
    Disconnect the connector.

  1. Put a 5 mm (0.197 in.) drill bit into a drill.

  1. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

    NOTICE:
    Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going to deep.

    Standard:
    Area
    Specified Condition
    A
    5 mm (0.197 in.)

  1. Lightly press the drill against the 3 rivets, drill off the flanges of the 3 rivets and remove the rear speaker assembly.

    CAUTION:
    Be careful of the drilled rivet as it may become hot.

    NOTICE:
    1. Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
    2. Do not pry the rivet with the drill because this may cause damage to the installation holes of the rivet or the drill bit.

  1. Continue drilling and push out the remaining rivet fragments.

  1. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.


10. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B277101E01
    Detach the claw and 2 guides as indicated by the arrows in the order shown in the illustration.

  1. B276830
    Disconnect the rear door inside locking cable and rear door lock remote control cable and remove the rear door inside handle.


11. REMOVE REAR DOOR NO. 2 TRIM BRACKET

  1. B277102
    Remove the 2 screws and rear door No. 2 trim bracket.


12. REMOVE REAR DOOR SERVICE HOLE COVER LH

  1. B281133
    w/ Rear Speaker:
    Pull out the rear door inside locking cable, rear door lock remote control cable and wire harness from the rear door service hole cover, and then remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.

  1. B281134
    w/o Rear Speaker:
    Pull out the rear door inside locking cable and rear door lock remote control cable from the rear door service hole cover, and then remove the rear door service hole cover.

    HINT:
    Remove any remaining butyl tape from the rear door panel.


13. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

  1. B277104
    Partially remove the rear door glass run as shown in the illustration.

  1. B277105
    Remove the 2 bolts.

  1. B277106
    Remove the rear door window division bar together with the rear door glass run as shown in the illustration.

  1. Remove the rear door window division bar from the rear door glass run.


14. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
  1. w/ Power Window:

    1. Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.

    2. Connect the cable to the negative (-) battery terminal.

    3. Move the rear door glass so that the rear door glass channel can be seen.

    4. Disconnect the cable from the negative (-) battery terminal.

      NOTICE:
      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    5. Remove the rear power window regulator switch assembly with rear door armrest base panel.

  1. w/o Power Window:

    1. Temporarily install the rear door window regulator handle.

    2. Move the rear door glass so that the rear door glass channel can be seen.

    3. Remove the rear door window regulator handle.

  1. B277107
    Remove the rear door glass from the rear door window regulator assembly as shown in the illustration.

  1. B277108E01
    Remove the rear door glass by passing it through the cutout of the rear door panel in the direction indicated by the arrow in the illustration.

    NOTICE:
    Do not damage the door glass.

    Text in Illustration 
    *a
    Rear Door Panel Cutout


15. REMOVE REAR DOOR GLASS RUN LH

  1. B277109
    Remove the front side of the rear door glass run.


16. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

  1. B281136E01
    Using a screwdriver, remove the rear door glass channel.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


17. REMOVE REAR DOOR GLASS CHANNEL FILLER

  1. B281137
    Remove the rear door glass channel filler.


18. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B281138E01
    w/ Power Window:

    1. Disconnect the connector.

    2. Loosen the temporary bolt.

      NOTICE:
      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.

      Text in Illustration 
      *1
      Temporary Bolt

    3. Remove the 3 bolts and rear door window regulator.

    4. Remove the temporary bolt from the rear door window regulator.

  1. B281139E01
    w/o Power Window:

    1. Loosen the temporary bolt.

      NOTICE:
      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.

      Text in Illustration 
      *1
      Temporary Bolt

    2. Remove the 2 bolts and rear door window regulator.

    3. Remove the temporary bolt from the rear door window regulator.


19. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Power Window)

  1. B288570
    Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor.


20. REMOVE REAR DOOR LOCK ASSEMBLY LH

  1. B291228
    w/ Power Door Lock:

    1. Disconnect the connector.

    2. Disconnect the rear door inside locking cable and rear door lock remote control cable from the clamps.

    3. Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock.

  1. B281140
    w/o Power Door Lock:

    1. Disconnect the rear door inside locking cable and rear door lock remote control cable from the clamps.

    2. Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock.


21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B281141
    Remove the rear door lock remote control cable.


22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B281142
    Detach the 3 claws and open the cover.

  1. B281143
    Remove the rear door inside locking cable.


23. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

  1. B277129
    Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle cover.


24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B277130
    Remove the rear door outside handle by sliding and pulling it in the direction indicated by the arrow in the illustration.


25. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B277131
    Using a T30 "TORX" socket wrench, loosen the screw and remove the rear door outside handle frame.


26. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

  1. B277132
    Detach the 2 claws and remove the rear door front outside handle pad.


27. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

  1. B277133
    Detach the 2 claws and remove the rear door rear outside handle pad.


28. REMOVE REAR DOOR PANEL CUSHION

  1. B277139
    Remove the rear door panel cushion.


29. REMOVE REAR DOOR WEATHERSTRIP LH

  1. B277138
    Remove the clip.

  1. Detach the 32 clips and remove the rear door weatherstrip.


30. REMOVE REAR DOOR CHECK ASSEMBLY LH

  1. B277137
    Remove the 3 bolts and rear door check.

← DISASSEMBLY (Aug 2012 – Jul 2013)ADJUSTMENT (from Jun 2011) →