CUSTOMIZE PARAMETERS
Removal / installation · Vehicles built from Jun 2011
| 1. CUSTOMIZE THEFT DETERRENT SYSTEM |
- HINT:
- The following items can be customized.
- During customize mode, the alarm control functions are disabled.
- During customize mode, the following wireless control functions are disabled: remote alarm function, automatic locking function, operation stop function and illuminated entry function.
- During customize mode, the ECU will not output lock/unlock signals.
- While in customize mode, if the key is inserted into the ignition key cylinder or a door is opened, customize mode will be canceled.
- The following items can be customized.
- NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Record the current settings before customizing.
- When the customer requests a change in a function, first make sure that the function can be customized.
Customizing with manual operation
Display
Default
Content
Setting
Relevant ECU
Shock sensor function
Standard
This function that adjusts sensitivity of the sensor that detects the intrusion.
Standard, Low, Max Low, Sensor off
Theft warning ECU assembly
| 2. CUSTOMIZE SHOCK SENSOR FUNCTION |
Customizing shock sensor function:
Check that the following conditions are met.
- No key is in the ignition key cylinder.
- The theft deterrent system is in the disarmed state (when either condition below is met):
- All the doors are in the unlocked condition and the doors are locked and unlocked using the door control transmitter assembly.
- The key is inserted into the ignition key cylinder, the ignition switch is turned to ON then off, and then the key is removed.
- The driver side door is opened (the other doors are closed).
- No key is in the ignition key cylinder.
Perform the following operation twice within 5 seconds:
- Insert the key into the ignition key cylinder, and then pull it out (ending with the key pulled out).
- Insert the key into the ignition key cylinder, and then pull it out (ending with the key pulled out).
Wait for 5 seconds.
After completing the above step, press and hold down the lock switch and unlock switch on the door control transmitter assembly at the same time for over 3 seconds within 5 seconds.
Check that the hazard warning lights flash once.
After completing the lock and unlock switch operation, perform the following operation within 5 seconds.
- Press the lock switch on the door control transmitter assembly 4 times within 2 seconds.
- Press the lock switch on the door control transmitter assembly 4 times within 2 seconds.
After completing the above step, press the unlock switch on door control transmitter assembly once within 2 seconds.
- HINT:
- After completing the above step, the present setting can be confirmed by pressing the unlock switch on the door control transmitter assembly once again.
Check that the hazard warning lights flash 4 times.
After completing the unlock switch operation, perform the following operations (mode select) within 10 seconds:
- Press the lock switch on door control transmitter assembly the number of times shown below depending on the desired function behavior to select the shock sensor function setting. Press the unlock switch on door lock transmitter once within 2 seconds of pressing the lock switch on door control transmitter assembly.
- HINT:
- If the lock switch on the door control transmitter is pressed 7 times or more, customize mode will be canceled.
- Shock sensor functioning: Sensor off
- Press the lock switch on door control transmitter assembly once.
- Shock sensor functioning: Max Low
- Press the lock switch on door control transmitter assembly twice.
- Shock sensor functioning: Low
- Press the lock switch on door control transmitter assembly 3 times.
- Shock sensor functioning: Standard
- Press the lock switch on door control transmitter assembly 4, 5 or 6 times.
Pattern 1Pattern 2Pattern 3Pattern 4- Press the lock switch on door control transmitter assembly the number of times shown below depending on the desired function behavior to select the shock sensor function setting. Press the unlock switch on door lock transmitter once within 2 seconds of pressing the lock switch on door control transmitter assembly.
Check the response to the select mode.
Response to Mode Select Operation
Setting
Hazard warning lights flash once
Max Low, Low, Standard
Hazard warning lights do not flash
Sensor off
- HINT:
- The customization setting can be set again within 30 seconds of the hazard warning lights flashing.
Check the response to the customize operation.
Response to Customize Operation
Setting
Hazard warning lights flash once
Sensor off
Hazard warning lights flash twice
Max Low
Hazard warning lights flash 3 times
Low
Hazard warning lights flash 4, 5 or 6 times
Standard
