2014 Hilux · Service Manual RESTRAINTS

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

CAUTION:
  1. The rear No. 1 seat inner belt assembly LH cannot be disconnected from the rear seat 3 point type belt assembly RH.
  2. When replacing the rear seat 3 point type belt assembly RH or rear No. 1 seat inner belt assembly LH, make sure to replace both with new ones.
  3. Make sure to connect the new rear seat 3 point type belt assembly RH and new rear No. 1 seat inner belt assembly LH.


1. INSTALL SEAT BELT BRACKET
  1. Install the seat belt bracket with the 2 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

  1. When reusing the rear seat 3 point type belt assembly RH:

    1. B360274E01
      Attach the 2 claws and temporarily install the rear 3 point type belt assembly RH retractor with the 2 bolts A and B.
      Text in Illustration 
      *1
      Bolt A
      *2
      Bolt B
      *3
      Bolt C

      NOTICE:
      When installing the rear 3 point type belt assembly RH retractor, make sure the claws of the seat belt bracket only contact the installation areas of the rear 3 point type belt assembly RH retractor.

    2. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      Bolt A:
      4.9 N*m{ 50 kgf*cm , 43 in.*lbf }
      Bolt B:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    3. Connect the upper part of the rear 3 point type belt assembly RH with the 2 bolts C

      Torque:
      Bolt C:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. When using a new rear seat 3 point type belt assembly RH:

    1. B354357E02
      Attach the 2 claws and temporarily install the rear 3 point type belt assembly RH retractor with the 2 bolts A and B.
      Text in Illustration 
      *1
      Bolt A
      *2
      Bolt B
      *3
      Bolt C

      NOTICE:
      When installing the rear 3 point type belt assembly RH retractor, make sure the claws of the seat belt bracket only contact the installation areas of the rear 3 point type belt assembly RH retractor.

    2. Tighten the 2 bolts in the order shown in the illustration.

      Torque:
      Bolt A:
      4.9 N*m{ 50 kgf*cm , 43 in.*lbf }
      Bolt B:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    3. Connect the upper part of the rear 3 point type belt assembly RH with the 2 bolts C

      Torque:
      Bolt C:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    4. Connect the new rear 3 point type belt assembly RH and new rear No. 1 seat inner belt assembly LH.

      CAUTION:
      Make sure to perform this step.


      B360275


3. INSTALL BACK PANEL TRIM
  1. Attach the 9 clips to install the back panel trim.

  1. Install the 4 clips.

  1. Attach the 3 claws and 2 guides to connect the cover to the back panel trim.


4. INSTALL REAR SEAT ASSEMBLY
  1. Fold up the rear seat cushion assembly.

  1. B360163E01
    Place the rear seat assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the 2 hooks and 2 guides.

    Text in Illustration 
    *1
    Hook
    *2
    Guide

  1. Attach the fold seat stopper band to the vehicle body and temporarily fix the rear seat cushion assembly in place.

  1. Temporarily install the rear seat assembly with the 4 bolts.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    20 N*m{ 199 kgf*cm , 14 ft.*lbf }

  1. Return the seat cushion to its original position.

  1. B360164E01
    Pass the rear No. 1 seat inner belt assembly LH through the seat cushion rubber band.
    Text in Illustration 
    *1
    Seat Cushion Rubber Band

  1. B360166E01
    Connect the rear No. 1 seat inner belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    1. Do not overlap the anchor part of the rear No. 1 seat inner belt assembly LH and protruding parts of the vehicle body.
    2. Make sure that the arrow on the rear No. 1 seat inner belt assembly LH floor anchor is facing towards the front of the vehicle.
    3. Connect the rear No. 1 seat inner belt assembly LH so that the angle of the floor anchor is with in the standard range.

      Standard:
      0°to 5°

    Text in Illustration  
    *1
    Protruding Part
    *2
    Floor Anchor
    *3
    Arrow
    *a
    Vehicle Front (0°)
    *b
    5°

  1. B360167E01
    Pass the rear No. 1 seat inner belt assembly RH through the seat cushion rubber band.
    Text in Illustration 
    *1
    Seat Cushion Rubber Band

  1. B360165E01
    Lock the seat cushion lock.

  1. Attach the fold seat stopper band button.

    Text in Illustration 
    *1
    Fold Seat Stopper Band Button


5. INSTALL REAR SEAT HINGE COVER LH

  1. B276875
    Attach the guide.

  1. Push the rear seat hinge cover LH to attach the 2 claws and install the rear seat hinge cover LH.


6. INSTALL REAR SEAT HINGE COVER RH

HINT:
Use the same procedures described for the LH side.

← INSPECTION (from Aug 2013)PRECAUTION (Jun 2011 – Jul 2013) →