Home › Power Source / Network › NETWORKING › MULTIPLEX COMMUNICATION SYSTEM
NM1840EF _57 Power Source / Network _010363 NETWORKING _0055295 MULTIPLEX COMMUNICATION SYSTEM GE GENERAL F

NETWORKING  MULTIPLEX COMMUNICATION SYSTEM  GENERAL  GENERAL  


OUTLINE


a.

The multiplex communication system uses the following communication protocol:

i.

The Controller Area Network (CAN) is used for communication between the engine, chassis, and body electrical system.



b.

HS-CAN (high speed) is used for the CAN.



MAIN FEATURES


a.

Multiplex communication uses serial communication data that consists of bits and frames in order to exchange information between the various ECUs. This allows a reduction of the amount of wiring used in the vehicle.

i.

A bit is the basic unit of communication used to represent the information. A bit is represented by binary values of "0" or "1".


ii.

A frame is a body of data transmitted together. A frame contains a header that indicates the beginning, and an end message that indicates the end.

Y110277
0.083,0.167 1.75,0.531 1.667,0.365 10 false Conceptual Drawing 3.833,0.802 4.385,1.167 0.552,0.365 10 false Data 3.833,2 4.448,2.323 0.615,0.323 10 false Frame 0.75,3.458 1.25,3.833 0.5,0.375 10 false Battery 2.083,4.333 2.698,4.698 0.615,0.365 10 false Switch 2.083,1.083 2.229,1.344 0.146,0.26 10 false 0 3.313,2.906 3.698,3.167 0.385,0.26 10 false On 3.302,3.271 3.542,3.531 0.24,0.26 10 false Off 2.771,3.333 3.167,3.719 0.396,0.385 10 false ECU 4.813,3.333 5.208,3.656 0.396,0.323 10 false ECU 2.083,0.677 2.406,0.938 0.323,0.26 10 false 1 5.198,1.417 6.333,1.719 1.135,0.302 10 false End Message 2.521,1.417 3.5,1.719 0.979,0.302 10 false Header 6.417,4.083 7.156,4.469 0.74,0.385 10 false Solenoid 6.417,3.667 7.156,4 0.74,0.333 10 false Heater 6.417,3.25 7.156,3.667 0.74,0.417 10 false Motor 6.417,2.833 7.156,3.167 0.74,0.333 10 false Light 0.083,0.833 1.969,1.198 1.885,0.365 10 false Serial Communication Data



b.

Differences between Types of CAN

i.

The CAN protocol is the rule for establishing data communication. If the ECUs in the network use different frameworks for their data, such as communication speed, communication wire, and signals, they will be unable to understand each other. Therefore, a protocol (rule) must be established among them.


ii.

The CAN is able to transmit larger amounts of data faster than other protocols. This feature makes it possible to transmit data accurately in the engine, chassis, and body electrical system, which requires large amounts of data to be transmitted in short periods of time.

Protocol CAN (ISO Standard)
Communication Speed 500 kbps*/HS-CAN (High Speed)
250 kbps*/MS-CAN (Medium Speed)
(Max. 1 Mbps*)
Communication Wire Twisted-pair Wire
Drive Type Differential Voltage Drive
Data Length 1-8 Bytes (Variable)

HINT:

*: bps is an abbreviation of "Bits Per Second", indicating the number of bits that can be transmitted per second.




c.

Communication Wire

i.

A twisted pair of wires is used for CAN communication. A single Automobile Vinyl (AV) wire is used for LIN communication.

Communication Wire Outline
Twisted-pair Wire
Y120656

This communication wire is a pair of twisted wires. Communication is driven by applying different voltages to the 2 lines in order to send a single signal. This system, which is called a "Differential Voltage Drive", reduces noise.

Y110278
2.927,1.417 4.25,1.719 1.323,0.302 10 false Twisted-pair Wire 2.688,2.083 4.583,2.385 1.896,0.302 10 false Differential Voltage Drive 2.25,1.083 2.771,1.385 0.521,0.302 10 false ECU 4.333,1.083 4.823,1.385 0.49,0.302 10 false ECU