Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2012.04
NM1840EF _51 Engine / Hybrid System _010304 1GR-FE ENGINE MECHANICAL _0055229 ENGINE UNIT DE DETAILS F

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER HEAD  


CONSTRUCTION


a.

The cylinder head, which is made of aluminum, contains a pentroof type combustion chamber. The spark plug has been located in the center of the combustion chamber in order to improve the engine's anti-knocking performance.


b.

The intake ports are on the inside and the exhaust ports are on the outside of the left and right banks respectively.


c.

Upright intake ports are used to improve the intake efficiency.


d.

A taper squish combustion chamber is used to improve anti-knocking performance and intake efficiency. In addition, engine performance and fuel economy have been improved.


e.

A siamese type intake port is used to reduce the overall surface area of the intake port walls. This prevents the fuel from adhering onto the intake port walls, thus reducing HC exhaust emissions.

W112604
0.417,0.5 3.583,3.417 3.167,2.917 3.75,0.5 6.917,3.417 3.167,2.917 5.771,3.073 5.771,2.823 false 6.385,3.073 5.052,3.073 5.052,3.073 5.052,2.823 false 3.292,2.458 3.177,2.458 3.177,2.458 2.521,2.094 true 2.375,1.948 3.167,1.667 3.167,1.667 3.333,1.667 true 2.583,1.781 3.25,1.083 3.25,1.083 3.333,1.083 true 4.031,2.552 4.198,2.552 4.198,2.552 4.448,2.135 true 0.5,0.583 0.677,0.802 0.177,0.219 10 false *a 1.646,0.844 1.844,1.104 0.198,0.26 10 false *b 6.396,2.073 6.615,2.323 0.219,0.25 10 false *c 3.844,0.573 4.031,0.813 0.188,0.24 10 false *d 3.896,1.844 4.052,2.198 0.156,0.354 10 false *b 3.344,2.365 3.542,2.594 0.198,0.229 10 false *3 6.469,2.958 6.677,3.229 0.208,0.271 10 false *5 3.854,2.448 4.073,2.667 0.219,0.219 10 false *4 3.375,1.573 3.531,1.927 0.156,0.354 10 false *2 3.365,0.969 3.531,1.219 0.167,0.25 10 false *1 2.427,0.688 2.667,0.917 0.24,0.229 10 false A 2.76,3.01 3,3.229 0.24,0.219 10 false A 1.698,2.719 1.917,2.969 0.219,0.25 10 false *c
*1 Intake Valve *2 Spark Plug Hole
*3 Exhaust Valve *4 Upright Intake Port
*5 Taper Squish - -
*a Bottom Side View *b Intake Side
*c Exhaust Side *d A - A Cross Section


HINT:

The difference between a siamese type intake port and independent type one is shown in the illustration.

W100680
0.577,0.471 0.865,0.71 0.288,0.24 12 *A: 4.36,0.471 4.662,0.71 0.302,0.24 12 *B:
*A Siamese Type *B Independent Type




f.

The cylinder head bolts have been positioned below the camshaft journal in the front of the right bank, and the holes for placing the bolts have been provided above the camshaft journal. Thus, the front end of the right bank has been shortened, resulting in a shorter overall length of the engine.

W104352
2.771,1.896 1.75,1.896 true 3.177,2.396 2.052,2.396 true 2.865,0.844 2.563,0.594 2.563,0.594 2.396,0.594 true 3.875,1.021 3.875,0.292 3.875,0.292 3.677,0.292 true 3.5,0.188 3.75,0.438 0.25,0.25 10 false *1 1.563,1.792 1.813,2.042 0.25,0.25 10 false *3 1.844,1.198 2.094,1.448 0.25,0.25 10 false *a 1.865,2.292 2.115,2.542 0.25,0.25 10 false *3 2.24,0.49 2.49,0.74 0.25,0.25 10 false *2
*1 Cylinder Head (Bank 1) *2 Cylinder Head Bolt
*3 Camshaft Journal - -
*a Shortened - -
V100135

Engine Front - -