FUNCTION OF MAIN COMPONENTS
The main components of the engine control system are as follows:
| Component | Outline | Quantity | Function |
|---|---|---|---|
| ECM | 32-bit CPU | 1 | The ECM effects overall control of the engine control system to suit the operating conditions of the engine in accordance with the signals provided by the sensors. |
| Injector Driver | DC/DC Converter | 1 | The injector driver is used to drive the injector at high speeds. The injector driver has achieved high-speed driving under high fuel pressure conditions through the use of a DC/DC converter that provides a high voltage, quick-charging system. |
| Turbo Pressure Sensor | Semiconductor Silicon Chip Type | 1 | This sensor uses built-in semiconductors to detect the intake manifold pressure. |
| Atmospheric Pressure Sensor | Semiconductor Silicon Chip Type | 1 | This sensor, which is built into the ECM, uses semiconductors to detect the atmospheric pressure. |
| Fuel Pressure Sensor | Semiconductor Strain Gauge Type | 1 | This sensor uses built-in semiconductors to detect the internal pressure of the common-rail. |
| Pressure Discharge Valve | Solenoid Type | 1 | The pressure discharge valve regulates the fuel pressure. |
| Crank Position Sensor | Pick-up Coil Type
(Rotor Teeth/36-2) |
1 | This sensor detects the engine speed and performs the cylinder identification. |
| Camshaft Position Sensor | Pick-up Coil Type
(Rotor Teeth/5) |
1 | This sensor performs the cylinder identification. |
| Intake Mass Air Flow Meter Sub-assembly | Hot-wire Type | 1 | This sensor uses a built-in hot-wire to directly detect the intake air mass. |
| Intake Air Temperature Sensor
(Built into Intake Mass Air Flow Meter Sub-assembly) |
Thermistor Type | 1 | This sensor detects the intake air temperature by means of an internal thermistor. |
| Intake Air Temperature Sensor
(Intercooler Outlet) |
Thermistor Type | 1 | This sensor detects the intake air temperature past the intercooler. |
| Engine Coolant Temperature Sensor | Thermistor Type | 1 | This sensor detects the engine coolant temperature by means of an internal thermistor. |
| Fuel Temperature Sensor | Thermistor Type | 1 | This sensor detects the fuel temperature in the supply pump by means of an internal thermistor. |
| Throttle Position Sensor | Non-contact Type | 1 | This sensor detects the diesel throttle valve opening angle. |
| Accelerator Pedal Position Sensor | Non-contact Type | 1 | This sensor detects the amount of pedal effort applied to the accelerator pedal. |
| Nozzle Vane Position Sensor | Non-contact Type | 1 | This sensor detects the nozzle vane position. |
| Suction Control Valve (SCV) | Linear Solenoid Valve | 1 | The SCV position is controlled by the signals from the ECM, and a fuel volume that suits the SCV position is drawn into the pumping portion (plunger portion). |
| Injector Assembly | 8-hole, Solenoid Type | 4 | The injector injects the fuel to the combustion chamber in accordance with the ECM signals via the injector driver. |
SYSTEM CONTROL
The engine control system has the following features. The ECM controls these systems:
| System | Outline |
|---|---|
| Fuel Injection Volume Control | Based on the signals received from the sensors, the ECM determines the fuel injection volume in accordance with the engine condition. |
| Fuel Injection Timing Control | Based on the signals received from the sensors, the ECM determines the fuel injection timing in accordance with the engine condition. |
| During Starting Control | To facilitate startability, the ECM optimally controls the injection volume and injection timing during starting. |
| Idle Speed Control | The ECM determines the idle speed in accordance with the engine condition, and controls the fuel injection volume in order to maintain the target idle speed. |
| Fuel Pressure Control | Based on the signals received from the sensors, the ECM controls fuel pressure using the Suction Control Valve (SCV) and pressure discharge valve in accordance with engine operating conditions. |
| Pilot Injection Control | Based on the signals received from the sensors, the ECM determines pilot injection volume/timing and interval (between pilot injection and main injection) in accordance with the engine condition. |
| Glow Plug Control | The ECM controls the length of time for which the current is applied to the glow plug assemblies, in accordance with the engine coolant temperature. |
| Diesel Throttle Control | ·
Controls the diesel throttle valve opening angle in accordance with the engine condition. ·
Fully closes the diesel throttle valve in order to reduce the vibration when the engine is stopped. |
| Swirl Control | Based on the signals received from the sensors, the ECM controls the vacuum that is directed to the actuator via the VSVs, in order to open and close the valve. Controls the valve opening in 3 stages: fully open, semi-open, and fully closed.*1 |
| Based on the signals received from the sensors, the ECM controls the vacuum that is directed to the actuator via the VSV, in order to open and close the valve. Controls the valve opening in 2 stages: fully open and fully closed.*2 | |
| Turbocharger Control | Based on the signals received from the sensors, the ECM controls the actuator in accordance with the engine condition. |
| Air Conditioning Cut-off Control*3 | By controlling the air conditioning compressor on or off in accordance with the engine condition, driveability is maintained. |
| Engine Immobiliser*4 | Prohibits fuel injection if an attempt is made to start the engine with an invalid ignition key. |
| Diagnosis | When the ECM detects a malfunction, it diagnoses and memorizes the failed section. |
| Fail-safe | When the ECM detects a malfunction, it stops or controls the engine in accordance with the data already stored in the memory. |
*1: Models compliant with EURO 4 emission regulations
*2: Except models compliant with EURO 4 emission regulations
*3: Models with air conditioning system
*4: Models with engine immobiliser system