FUNCTION OF MAIN COMPONENTS
The main components of the engine control system are as follows:
| Component | Outline | Quantity | Function |
|---|---|---|---|
| ECM | 32-bit CPU | 1 | The ECM optimally controls the SFI, ESA and ISC to suit the operating conditions of the engine in accordance with the signals provided by the sensors. |
| Intake Mass Air Flow Meter Sub-assembly | Hot-wire Type | 1 | This sensor has a built-in hot-wire to directly detect the intake air mass. |
| Intake Air Temperature Sensor | Thermistor Type | 1 | This sensor detects the intake air temperature by means of an internal thermistor. |
| Engine Coolant Temperature Sensor | Thermistor Type | 1 | This sensor detects the engine coolant temperature by means of an internal thermistor. |
| Crankshaft Position Sensor [Rotor Teeth] | Pick-up Coil Type (36-2) | 1 | This sensor detects the engine speed and performs cylinder identification. |
| Camshaft Position Sensor [Rotor Teeth] | Pick-up Coil Type (3) | 1 | This sensor performs the cylinder identification. |
| Accelerator Pedal Position Sensor | Linear (Non-contact) Type | 1 | This sensor detects the amount of pedal effort applied to the accelerator pedal. |
| Throttle Position Sensor | Linear (Non-contact) Type | 1 | This sensor detects the throttle valve opening angle. |
| Knock Control Sensor | Built-in Piezoelectric Type (Non-resonant Type/Flat Type) | 1 | This sensor detects an occurrence of engine knocking indirectly from the vibration of the cylinder block caused by the occurrence of engine knocking. |
| Air Fuel Ratio Sensor* | Heated Type (Planar Type) | 1 | As with the oxygen sensor, this sensor detects the oxygen concentration in the exhaust emissions. However, it detects the oxygen concentration in the exhaust emissions linearly. |
| Oxygen Sensor | Heated Type (Cup Type) | 1 | This sensor detects the oxygen concentration in the exhaust emissions by measuring the electromotive force which is generated in the sensor itself. |
| Fuel Injector Assembly | 12-hole Type | 4 | The fuel injector assembly is an electromagnetically-operated nozzle which injects fuel in accordance with signals from the ECM. |
*: Models compliant with EURO 3 and EURO 4 emission regulations
SYSTEM CONTROL
The engine control system has the following features. The ECM controls these systems:
| System | Outline |
|---|---|
| Sequential Multiport Fuel Injection (SFI) | ·
An L-type SFI system directly detects the intake air mass with a hot wire type intake mass air flow meter sub-assembly. ·
The fuel injection system is a sequential multiport fuel injection system. ·
Fuel injection takes two forms: ·
Synchronous injection, which always takes place with the same timing in accordance with the basic injection duration and an additional correction based on the signals provided by the sensors. ·
Non-synchronous injection, which takes place at the time an injection request based on the signals provided by the sensors is detected, regardless of the crankshaft position. ·
Synchronous injection is further divided into group injection during a cold start, and independent injection after the engine is started. |
| Electronic Spark Advance (ESA) | ·
Ignition timing is determined by the ECM based on signals from various sensors. The ECM corrects ignition timing in response to engine knocking. ·
This system selects the optimal ignition timing in accordance with the signals received from the sensors and sends the (IGT) ignition signal to the igniter. |
| Electronic Throttle Control System-intelligent (ETCS-i) | Optimally controls the throttle valve opening in accordance with the amount of accelerator pedal effort and the condition of the engine and the vehicle. |
| Variable Valve Timing-intelligent (VVT-i) | Controls the intake camshaft to an optimal valve timing in accordance with the engine condition. |
| Fuel Pump Control | ·
Fuel pump operation is controlled by signals from the ECM. ·
The fuel pump is stopped when the Supplemental Restraint System (SRS) airbags are deployed.*1 |
| Air Conditioning Cut-off Control*2 | By turning the air conditioning compressor assembly on or off in accordance with the engine condition, driveability is maintained. |
| Air Fuel Ratio Sensor*3 and Oxygen Sensor Heater Control | Maintains the temperature of the air fuel ratio sensors or oxygen sensors at an appropriate level to increase the detection accuracy of the exhaust gas oxygen concentration. |
| Engine Immobiliser*4 | Prohibits fuel delivery and ignition if an attempt is made to start the engine with an invalid key. |
| Diagnosis | When the ECM detects a malfunction, it diagnoses and memorizes the failed section. |
| Fail-safe | When the ECM detects a malfunction, it stops or controls the engine in accordance with the data already stored in memory. |
*1: Models with SRS airbag system
*2: Models with air conditioning system
*3: Models compliant with EURO 3 and EURO 4 emission regulations
*4: Models with engine immobiliser system