Home › Engine / Hybrid System › 1KD-FTV FUEL › FUEL SYSTEM › 2011.10–2012.04
NM1840EF _51 Engine / Hybrid System _010307 1KD-FTV FUEL _0055232 FUEL SYSTEM DE DETAILS F

1KD-FTV FUEL  FUEL SYSTEM  DETAILS  SUPPLY PUMP  


CONSTRUCTION


a.

An HP3 type supply pump is used.

W102867
3.531,2.281 3.656,2.469 0.125,0.188 10 false A 3.875,2.104 4,2.271 0.125,0.167 10 false B

Supply Pump Specifications
Type HP3
Length A 190.2 mm (7.49 in.)
B 129.0 mm (5.08 in.)
SCV 1
Plunger φ 8.5 mm x 2
Weight 3800 g (8.38 lb)

HINT:
·

The ECM learns and memorizes the pump discharge volume variances associated with the individual differences in the supply pumps. Therefore, make sure to perform the operation described below after replacing the supply pump. For details, refer to the Repair Manual.

·

Connect an intelligent tester II to the DLC3 connector and use the tester to reset the learned value. Alternatively, connect the SST (09843-18040) between the TC and CG terminals of the DLC3 connector, and leave the ignition switch ON for approximately 3 minutes to reset the learned value.

·

After resetting, start the engine, allow it to idle* for approximately 1 minute, and turn the ignition switch off to enable the engine to memorize the learned value.


*: The engine coolant temperature should be 60°C (140°F) or more, and the fuel temperature should be 20°C (68°F) or more.




b.

The supply pump consists of an eccentric camshaft, a ring cam, 2 plungers, 4 check valves, a Suction Control Valve (SCV), a fuel temperature sensor, and a feed pump.


c.

The 2 plungers are placed opposite each other outside of the ring cam.

W104112
1.344,0.823 1.875,0.292 1.875,0.292 2.188,0.292 true 1.469,1.073 1.99,0.552 1.99,0.552 2.188,0.552 true 1.677,2.969 1.24,2.542 1.24,2.542 0.99,2.542 true 2.052,2.833 2.677,3.448 2.677,3.448 2.906,3.448 true 1.74,4.646 2.135,5.031 2.135,5.031 2.354,5.031 true 1.604,4.302 1.188,3.885 1.188,3.885 1.021,3.885 true 2.333,6.333 1.979,5.979 1.979,5.979 1.604,5.979 true 2.333,6.719 1.833,6.208 1.833,6.208 1.635,6.208 true 2.333,8.292 1.979,8.646 1.979,8.646 1.604,8.646 true 2.323,7.896 1.823,8.406 1.823,8.406 1.625,8.406 true 1.729,7.198 1.333,6.792 1.333,6.792 1.208,6.792 true 2.531,6.469 2.844,6.167 2.844,6.167 2.948,6.167 true 3.031,7.073 3.302,6.802 3.302,6.802 3.427,6.802 true 2.469,7.208 3.281,8.021 3.281,8.021 3.417,8.021 true 2.354,7.542 3.135,8.323 3.135,8.323 3.448,8.323 true 5.177,7.292 4.438,6.552 4.438,6.552 4.323,6.552 true 5.469,7.521 6.146,8.198 6.146,8.198 6.344,8.198 true 4.677,3.333 4.167,3.844 4.167,3.844 3.99,3.844 true 5.479,3.396 5.813,3.74 5.813,3.74 6.052,3.74 true 5.25,3.063 6.083,3.063 true 5.552,0.875 6.042,0.385 6.042,0.385 6.229,0.385 true 5,1.073 5,1.604 true 2.385,4.927 2.552,5.104 0.167,0.177 10 false *1 1.438,5.885 1.604,6.063 0.167,0.177 10 false *1 1.438,8.542 1.604,8.719 0.167,0.177 10 false *1 0.802,2.458 0.969,2.635 0.167,0.177 10 false *3 1.042,6.698 1.208,6.875 0.167,0.177 10 false *3 2.979,6.063 3.146,6.24 0.167,0.177 10 false *5 6.271,0.302 6.438,0.479 0.167,0.177 10 false *5 3.448,6.708 3.615,6.885 0.167,0.177 10 false *6 6.115,2.969 6.281,3.146 0.167,0.177 10 false *6 6.083,3.635 6.25,3.813 0.167,0.177 10 false *7 3.813,3.75 3.979,3.927 0.167,0.177 10 false *8 3.448,7.917 3.615,8.094 0.167,0.177 10 false *9 4.146,6.448 4.313,6.625 0.167,0.177 10 false *9 2.938,3.354 3.104,3.531 0.167,0.177 10 false *4 3.479,8.229 3.646,8.406 0.167,0.177 10 false *4 6.385,8.094 6.552,8.271 0.167,0.177 10 false *4 2.24,0.469 2.406,0.646 0.167,0.177 10 false *2 2.885,1.833 3.052,2.01 0.167,0.177 10 false *a 4.938,0.177 5.104,0.354 0.167,0.177 10 false *b 4.927,1.615 5.094,1.792 0.167,0.177 10 false *c 2.24,0.198 2.406,0.375 0.167,0.177 10 false *1 0.844,3.792 1.01,3.969 0.167,0.177 10 false *2 1.458,6.104 1.625,6.281 0.167,0.177 10 false *2 1.458,8.313 1.625,8.49 0.167,0.177 10 false *2
*1 Check Valve (for Suction) *2 Plunger
*3 Eccentric Camshaft *4 Ring Cam
*5 Check Valve (for Discharge) *6 Feed Pump
*7 Fuel Temperature Sensor *8 SCV
*9 Eccentric Cam Portion - -
*a From Fuel Tank (for Suction) *b To Fuel Tank (for Return)
*c To Common-rail - -




OPERATION


a.

Due to the rotation of the eccentric cam, the ring cam pushes plunger "A" upward as illustrated below. The force of the spring pulls plunger "B" (which is located opposite plunger "A") upward. As a result, plunger "B" draws fuel in, and plunger "A" pumps fuel at the same time.

W102348
1.604,0.406 1.604,0.156 1.604,0.156 1.469,0.156 true 0.5,1.656 0.5,1.406 0.5,1.406 0.365,1.406 true 2.49,0.406 2.49,0.156 2.49,0.156 2.625,0.156 true 2.01,1.406 1.115,0.51 1.115,0.51 0.927,0.51 true 2.344,1.26 2.448,1.156 2.448,1.156 2.521,1.156 true 2.104,0.927 2.448,0.792 2.448,0.792 2.542,0.792 true 2.198,1.979 2.51,2.115 2.51,2.115 2.583,2.115 true 1.281,0.063 1.49,0.25 0.208,0.188 10 false *1 0.74,0.417 0.948,0.604 0.208,0.188 10 false *3 2.563,0.698 2.75,0.885 0.188,0.188 10 false *4 2.552,1.063 2.74,1.25 0.188,0.188 10 false *5 0.49,2.333 0.677,2.521 0.188,0.188 10 false *8 0.188,1.313 0.375,1.5 0.188,0.188 10 false *7 2.594,2.021 2.781,2.208 0.188,0.188 10 false *6 2.656,0.063 2.865,0.25 0.208,0.188 10 false *2
*1 Check Valve (for Suction) *2 Check Valve (for Discharge)
*3 Eccentric Cam *4 Plunger "A"
*5 Ring Cam *6 Plunger "B"
*7 Suction Control Valve (SCV) *8 ECM



b.

The ECM controls the opening of the SCV in order to regulate the volume of fuel that is pumped by the supply pump to the common-rail. Consequently, the fuel pressure in the common-rail is controlled to the target injection pressure.


c.

When the opening of the SCV is small, the fuel suction area is kept small, which decreases the transferable fuel quantity.


d.

When the plunger strokes fully, however, the suction volume becomes small due to the small suction area.


e.

Pumping will start when the fuel pressure has become higher than the common-rail pressure.

W102349
1.604,0.521 1.5,0.292 1.5,0.292 1.438,0.292 true 3.771,0.51 3.865,0.281 3.865,0.281 3.927,0.281 true 5.135,0.51 5.24,0.135 5.24,0.135 5.302,0.135 true 3.146,0.667 3.146,0.146 3.146,0.146 3.052,0.146 true 0.844,1.958 0.969,1.74 0.969,1.74 1.031,1.74 true 0.823,2.208 0.823,2.531 true 0.052,0.917 0.823,1.24 0.771,0.323 10 false Cam Stroke 1.531,3.26 1.75,3.583 0.219,0.323 10 false (c) 3.375,3.271 3.594,3.594 0.219,0.323 10 false (d) 5.083,3.271 5.302,3.594 0.219,0.323 10 false (e) 0.448,2.542 1.344,3.146 0.896,0.604 10 false Small Suction Area 0.625,0.198 1.479,0.521 0.854,0.323 10 false Plunger TDC 3.979,0.188 4.813,0.427 0.833,0.24 10 false Plunger BDC 1.792,0.052 3.083,0.375 1.292,0.323 10 false Fuel Pumping Mass 5.354,0.042 6.833,0.208 1.479,0.167 10 false Pumping Starting Point 1.073,1.656 1.417,1.979 0.344,0.323 10 false SCV


f.

When the opening of the SCV is large, the fuel suction area is kept large, which increases the transferable fuel quantity.


g.

If the plunger strokes fully, the suction volume will increase because the suction area is large.


h.

Pumping will start at the time when the fuel pressure has become higher than the common-rail pressure.

W102350
4.135,0.479 4.24,0.104 4.24,0.104 4.302,0.104 true 3.365,0.646 3.365,0.094 3.365,0.094 3.271,0.094 true 1.052,1.875 1.177,1.656 1.177,1.656 1.24,1.656 true 1.042,2.146 1.042,2.479 true 0.313,0.813 1.083,1.135 0.771,0.323 10 false Cam Stroke 1.75,3.177 1.969,3.5 0.219,0.323 10 false (f) 3.75,3.177 3.969,3.5 0.219,0.323 10 false (g) 5.698,3.177 5.917,3.5 0.219,0.323 10 false (h) 1.281,1.573 1.625,1.896 0.344,0.323 10 false SCV 0.708,2.49 1.604,3.094 0.896,0.604 10 false Large Suction Area 2.01,0.01 3.302,0.333 1.292,0.323 10 false Fuel Pumping Mass 4.354,0.021 5.875,0.344 1.521,0.323 10 false Pumping Starting Point