Home › Drivetrain › A343F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
NM1840EF _52 Drivetrain _010338 A343F AUTOMATIC TRANSMISSION / TRANSAXLE _0055268 AUTOMATIC TRANSMISSION SYSTEM CO CONTROL F

A343F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  CONTROL  AUTOMATIC TRANSMISSION CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Torque Converter Assembly
·

Transmits the engine power to the transmission.

·

Increases engine torque.


Oil Pump Provides oil pressure necessary for the transmission operation.
Overdrive Direct Clutch (C0) Connects the overdrive planetary sun gear and the overdrive planetary carrier.
Forward Clutch (C1) Connects the input shaft and the front planetary ring gear.
Direct Clutch (C2) Connects the input shaft and the front and rear planetary sun gear.
Overdrive Brake (B0) Prevents the overdrive planetary sun gear from turning either clockwise or counterclockwise.
2nd Coast Brake (B1) Prevents the front and rear sun gear from turning either clockwise or counterclockwise.
2nd Brake (B2) Prevents the outer race of F1 from turning either clockwise or counterclockwise, thus preventing the front and rear sun gear from turning counterclockwise.
1st and Reverse Brake (B3) Prevents the rear planetary carrier from turning either clockwise or counterclockwise.
Overdrive 1-way Clutch (F0) Connects the overdrive planetary sun gear and the planetary carrier when engine power is transmitted to the overdrive input shaft.
1-way Clutch Assembly (F1) Prevents the front and rear planetary sun gear from turning counterclockwise when B2 is operating.
No. 2 1-way Clutch (F2) Prevents the rear planetary carrier from turning counterclockwise.
Planetary Gears Change power transmission route in accordance with clutch and brake operation, and increase or decrease output shaft revolutions accordingly.
Shift Solenoid Valve S1 and S2 Switch the shift valves.
Shift Solenoid Valve SLT Controls line pressure.
Shift Solenoid Valve SL Controls the lock-up clutch.
ATF Temperature Sensor Detects the ATF temperature.
Input Speed Sensor (NCO) Detects the input speed of the transmission.
Output Speed Sensor (SP2) Detects the output speed of the transmission.
Park/Neutral Position Switch Assembly Detects the shift lever position (P, R, N, D, 2, L).
Shift Lock Control ECU Sub-assembly Transmission Control Switch Detects that the shift lever is in 3.
Transfer Indicator Switch (L4 Position) Detects that the transfer gear position is low.
Transfer Indicator Switch (Neutral Position) Detects that the transfer gear position is neutral.
4WD Control ECU Transmits a signal transfer gear position is 4WD to the ECM.
ECM
·

Controls each shift solenoid valve and engine output in response to a signal from each sensor and switch.

·

Makes a diagnosis and memorizes the failed section when the ECM detects a malfunction.


Combination Meter Assembly Shift Position Indicator Light Indicates the shift lever position.
MIL Illuminates or blinks to inform the driver when the ECM detects a malfunction.
ATF Temperature Warning Light Warns the driver by lighting up when the ATF is at a high temperature.
DLC3 The Diagnostic Trouble Codes (DTCs) can be read by connecting an intelligent tester II.


SYSTEM CONTROL


Electronic Control of Automatic Transmission
Control Function
Shift Timing Control The ECM sends current to the shift solenoid valves S1 and/or S2 based on signals from various sensors in order to shift the gears.
Line Pressure Control Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM and the operating conditions of the transmission.
Engine Torque Control Retards the ignition timing temporarily to improve shift feeling during upshifting or downshifting.
N to D Squat Control When the shift lever is moved from N to D, the gear is temporarily engaged to the 4th and then to the 1st to reduce vehicle squat.
Lock-up Timing Control The ECM sends current to the shift solenoid valve SL based on signals from various sensors and engages or disengages the lock-up clutch.

a.

Line Pressure Control

i.

In order to obtain a predetermined line pressure characteristic in accordance with each sensor signal, the ECM activates the shift solenoid valve SLT to regulate the throttle pressure.


ii.

This makes it possible for the primary regulator valve to precisely and minutely control the line pressure in accordance with the engine output, thus providing smoother shift characteristics.

X105538
1.563,3.979 1.677,4.271 true 1.427,4.313 2.115,4.646 0.688,0.333 10 false Oil Pump 1.844,3.135 2.802,3.469 0.958,0.333 10 false Line Pressure 3.073,1.083 4,1.792 0.927,0.708 10 false Solenoid Valve Drive Signal 1.115,1.979 1.677,2.656 0.563,0.677 10 false Throttle Pressure 0.125,3.344 1.24,3.885 1.115,0.542 10 false Primary Regulator Valve 5.552,0.531 7.083,0.865 1.531,0.333 10 false ATF Temperature Signal 5.552,0.865 7.063,1.208 1.51,0.344 10 false Shift Position Signal 5.552,1.229 7.135,1.563 1.583,0.333 10 false Input Speed Signal 5.542,1.573 7.125,1.906 1.583,0.333 10 false Output Speed Signal 5.552,1.927 7.135,2.26 1.583,0.333 10 false Vehicle Speed Signal 5.552,2.75 6.656,3.281 1.104,0.531 10 false Accelerator Pedal Position Signal 5.552,4.083 6.76,4.771 1.208,0.688 10 false Crankshaft Position Signal 2.125,3.625 2.677,4.302 0.552,0.677 10 false Line Pressure 2.833,4.094 3.854,4.677 1.021,0.583 10 false Throttle Opening Angle 4.406,2.333 4.813,2.667 0.406,0.333 10 false ECM 5.542,3.365 6.729,4.052 1.188,0.688 10 false Engine Coolant Temperature Signal 2.073,2.479 3.292,3 1.219,0.521 10 false Shift Solenoid Valve SLT



b.

Engine Torque Control

i.

Engagement of the clutches and brakes of the planetary gear unit in the transmission is controlled smoothly by momentarily retarding the engine ignition timing when gears are shifted up or down in the transmission. When the ECM judges a gear shift timing in accordance with signals, it activates the shift solenoid valves to perform gear shifting. When the gear shifting starts, the ECM retards the engine ignition timing to reduce the engine torque. As a result, engagement force of the clutches and brakes of the planetary gear units is weakened and the gear change is performed smoothly.

X105541
1.323,0.698 2.729,1.031 1.406,0.333 10 false Vehicle Speed Signal 5.667,1.021 6.656,1.698 0.99,0.677 10 false Throttle Position Signal 3.833,0.896 4.219,1.229 0.385,0.333 10 false ECM 4.771,2.531 5.698,2.865 0.927,0.333 10 false Speed Signal 3.031,1.917 3.313,2.25 0.281,0.333 10 false (d) 1.396,2.156 2.813,2.49 1.417,0.333 10 false Ignition Coil with Igniter 1.646,4.802 2.177,5.135 0.531,0.333 10 false Normal 1.563,5.354 5.01,5.688 3.448,0.333 10 false (a) : Judgment of gear shifting 1.563,5.708 5.01,6.042 3.448,0.333 10 false (b) : Determination of ignition timing retard angle 1.563,6.083 5.01,6.417 3.448,0.333 10 false (c) : Gear shifting 1.563,6.458 5.01,6.792 3.448,0.333 10 false (d) : Retarding ignition timing 1.563,6.802 5.01,7.135 3.448,0.333 10 false (e) : Torque reduction 2.177,4.802 2.865,5.135 0.688,0.333 10 false Reducing 1.396,1.448 3.052,1.896 1.656,0.448 10 false Crankshaft Position Signal 3.115,4.115 5.615,5.115 2.5,1 10 false When engine torque is reduced, clutches and brakes are engaged with less force and gear shifting is performed smoothly. 1.094,4.198 1.531,4.781 0.438,0.583 10 false Engine Torque 4,2.479 4.281,2.813 0.281,0.333 10 false (a) 2.438,2.927 2.719,3.26 0.281,0.333 10 false (e) 3.656,2.01 3.938,2.344 0.281,0.333 10 false (c) 3.583,0.885 3.865,1.219 0.281,0.333 10 false (b)



c.

Lock-up Timing Control

i.

The ECM operates the lock-up timing control in order to improve the fuel consumption performance in the top gear when the shift lever is in D or 3.

Lock-up Timing Control Operation
Gear Shift Lever Position
D 3
1st X X
2nd X X
3rd X ○
4th ○ -

HINT:

○: Operates

X: Does not operate





FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a solenoid.

Fail-safe Control List
Malfunction Part Function
Output Speed Sensor (SP2) During an output speed sensor malfunction, shift control is effected through the input speed sensor signal (NCO) or engine speed signal (NE).
ATF Temperature Sensor During a malfunction of the ATF temperature sensor, the system effects control by fixing the ATF temperature at 80°C (176°F).
Shift Solenoid Valve S1/S2 The current to the failed shift solenoid valve is cut off and control is effected by operating the other solenoid valves with normal operation.
Shift Solenoid Valve SLT During a shift solenoid valve SLT malfunction, the current to the shift solenoid valve is stopped. This stops line pressure control, thus increasing shift shock. However, shifting is effected through normal clutch pressure control.
Shift Solenoid Valve SL During a shift solenoid valve SL malfunction, the current to the shift solenoid valve is stopped. This stops lock-up control, thus decreasing fuel economy.



DIAGNOSIS


a.

When the ECM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the ECM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The ECM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions.


c.

The DTCs can be read by connecting an intelligent tester II to the DLC3.


d.

For details, refer to the Repair Manual.