Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM › from 2012.04
NM1840EF _52 Drivetrain _010339 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0055269 AUTOMATIC TRANSMISSION SYSTEM CO CONTROL F

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  CONTROL  AUTOMATIC TRANSMISSION CONTROL  


FUNCTION OF MAIN COMPONENTS


Component Function
Torque Converter Assembly
·

Transmits the engine power to the transmission.

·

Increases engine torque.


Oil Pump Provides the oil pressure necessary for the transmission operation.
No. 1 Clutch (C1) Connects the input shaft and the intermediate shaft.
No. 2 Clutch (C2) Connects the input shaft and the center planetary carrier.
No. 3 Clutch (C3) Connects the input shaft and the front sun gear.
No. 1 Brake (B1) Prevents the front planetary carrier from turning either clockwise or counterclockwise.
No. 2 Brake (B2) Prevents the front and center planetary ring gears from turning either clockwise or counterclockwise.
No. 3 Brake (B3) Prevents the outer race of F2 from turning either clockwise or counterclockwise.
No. 4 Brake (B4) Prevents the center planetary carrier and the rear planetary ring gear from turning either clockwise or counterclockwise.
No. 1 1-way Clutch (F1) Prevents the front planetary carrier from turning counterclockwise.
No. 2 1-way Clutch (F2) Prevents the front planetary sun gear from turning counterclockwise when B3 is operating.
No. 3 1-way Clutch (F3) Prevents the center planetary carrier and the rear planetary ring gear from turning counterclockwise.
Planetary Gears Change the route through which driving force is transmitted, in accordance with the operation of each clutch and brake, in order to increase or reduce the input and output speed.
Shift Solenoid Valve DSL (S1) Switches the 2-3 shift valve.
No. 3 Transmission Solenoid Assembly (S2) Switches the 1-2 shift valve or 3-4 shift valve.
Shift Solenoid Valve S4 (SR) Switches the clutch apply control valve.
Shift Solenoid Valve (SL1)
·

Controls clutch pressure.

·

Controls accumulator back pressure.


Shift Solenoid Valve (SL2) Controls brake pressure.
Line Pressure Control Solenoid Assembly (SLT)
·

Controls line pressure.

·

Controls accumulator back pressure.


Lock-up Control Solenoid Assembly (SLU)
·

Controls lock-up clutch pressure.

·

Controls accumulator back pressure.


ATF Temperature Sensors Detect the ATF temperature.
Transmission Revolution Sensor (NT) Detects the input speed of the transmission.
Transmission Revolution Sensor (SP2) Detects the output speed of the transmission.
Park/Neutral Position Switch Assembly Detects the shift lever position (P, R, N, D, 3, 2).
Shift Lock Control ECU Sub-assembly Transmission Control Switch Detects that the shift lever is in 4 and L.
Transfer Indicator Switch (L4 Position) Detects that the transfer gear position is low.
Transfer Indicator Switch (Neutral Position) Detects that the transfer gear position is neutral.
4WD Control ECU Transmits a signal to inform the ECM that the transfer gear position is 4WD.*1
ECM
·

Controls each shift solenoid valve and engine output in response to a signal from each sensor and switch.*1

·

Controls engine output in response to a signal from the TCM.*2

·

Makes a diagnosis and memorizes the failed section when the ECM detects a malfunction.


TCM*2 Controls each shift solenoid valve in response to a signal from each sensor and switch.
Combination Meter Assembly Shift Position Indicator Light Indicates the shift lever position.
MIL Illuminates or blinks to inform the driver when the ECM or TCM detects a malfunction.
ATF Temperature Warning Light Warns the driver by lighting up when the ATF is at a high temperature.
DLC3 The Diagnostic Trouble Codes (DTCs) can be read by connecting an intelligent tester II.

*1: Models with 1GR-FE engine

*2: Models with 1KD-FTV engine



SYSTEM CONTROL


Electronic Control of Automatic Transmission
Control Function
Shift Timing Control The ECM or TCM sends current to shift solenoid valves S1, S2 and/or SR based on signals from various sensors in order to shift the gears.
Line Pressure Control Actuates the shift solenoid valve SLT to control the line pressure in accordance with information from the ECM or TCM and the operating conditions of the transmission.
Clutch Pressure Optimal Control The shift solenoid valves SL1 and SLT minutely control the clutch pressure in accordance with the engine output and driving conditions of the transmission.
Clutch to Clutch Pressure Control Controls the pressure that is applied directly to B1 brake and C1 clutch by actuating the shift solenoid valves SL1 and SL2 in accordance with the ECM or TCM signals.
Engine Torque Control Retards the engine ignition timing temporarily to improve shift feeling when upshifts or downshifts occur.*1
Reduces the fuel injection volume temporarily to improve shift feeling when upshifts or downshifts occur.*2
N to D Squat Control When the shift lever is moved from N to D, the gear is temporarily engaged to the 2nd and then to the 1st to reduce vehicle squat.
Lock-up Timing Control The ECM or TCM sends current to the shift solenoid valve SLU based on signals from various sensors and engages or disengages the lock-up clutch.
Flex Lock-up Clutch Control*2 Controls the shift solenoid valve SLU, provides an intermediate mode for when the lock-up clutch is between on and off, and increases the operating range of the lock-up clutch to improve fuel economy.
Artificial Intelligence-shift Control (AI-shift Control) Based on the signals from various sensors, the ECM or TCM determines the road conditions and the intention of the driver. Then, an appropriate shift pattern is automatically determined, thus improving driveability.

*1: Models with 1GR-FE engine

*2: Models with 1KD-FTV engine


a.

Line Pressure Control

i.

In order to obtain a predetermined line pressure characteristic in accordance with each sensor signal, the ECM or TCM activates the shift solenoid valve SLT to regulate the throttle pressure.


ii.

This makes it possible for the primary regulator valve to precisely and minutely control the line pressure in accordance with the engine output, thus providing smoother shift characteristics.

X105618
3.063,3.885 4.104,4.688 1.042,0.802 10 false Line Pressure Control Solenoid Assembly (SLT) 1.031,3.75 1.646,4.76 0.615,1.01 10 false Primary Regulator Valve 0.448,1.01 1.417,1.365 0.969,0.354 10 false Line Pressure 0.167,3.031 0.573,3.396 0.406,0.365 10 false Pump 3.979,0.146 4.917,0.833 0.938,0.688 10 false Solenoid Valve Drive Signal 5.646,0.552 6.948,0.917 1.302,0.365 10 false Input Turbine Speed 5.635,0.938 6.781,1.302 1.146,0.365 10 false ATF Temperature 5.656,1.344 6.542,1.708 0.885,0.365 10 false Shift Position 5.635,3.573 6.802,3.938 1.167,0.365 10 false Intake Air Mass*1 5.646,1.74 6.552,2.104 0.906,0.365 10 false Gear Position 5.656,4.375 6.604,4.74 0.948,0.365 10 false Engine Speed 5.667,4.792 6.625,5.479 0.958,0.688 10 false Engine Coolant Temperature 5.635,3.969 7.146,4.333 1.51,0.365 10 false Fuel Injection Volume*2 5.094,2.125 5.427,3.135 0.333,1.01 10 false ECM or TCM 1.74,1.26 2.323,1.906 0.583,0.646 10 false Fluid Pressure 2.635,2.229 3.167,2.594 0.531,0.365 10 false Current 5.635,2.875 6.75,3.542 1.115,0.667 10 false Accelerator Pedal Opening Angle*2 5.635,2.167 6.688,2.833 1.052,0.667 10 false Throttle Valve Opening Angle*1 0.125,5.375 2.219,5.74 2.094,0.365 10 false *2: Models with 1KD-FTV engine 0.115,5 2.208,5.365 2.094,0.365 10 false *1: Models with 1GR-FE engine



b.

Clutch Pressure Optimal Control

i.

The ECM or TCM monitors the signals from various types of sensors, such as the transmission revolution sensor (NT), allowing shift solenoid valves SL1 and SLT to minutely control the clutch pressure in accordance with engine output and driving conditions. As a result, smooth shift characteristics are achieved.

X102176
4.25,3.896 5.094,4.094 5.094,4.094 5.094,4.313 true 3.729,3.917 3.323,4.104 3.323,4.104 2.896,4.104 true 4.052,3.906 3.156,4.49 3.156,4.49 2.677,4.49 true 3.594,3.198 3.177,2.479 3.177,2.479 2.719,2.479 true 4.615,3.156 4.99,2.448 4.99,2.448 5.344,2.448 true 5.406,2.354 6.938,3.042 1.531,0.688 10 false Transmission Revolution Sensor (SP2) 4.292,4.344 5.927,4.698 1.635,0.354 10 false ATF Temperature Sensor 0.385,2.396 2.75,2.75 2.365,0.354 10 false Transmission Revolution Sensor (NT) 1.25,4.021 2.99,4.375 1.74,0.354 10 false Accumulator Control Valve 0.708,4.396 2.802,4.74 2.094,0.344 10 false Shift Solenoid Valve (SL1, SLT) 5.771,0.615 6.125,1.135 0.354,0.521 10 false ECM or TCM 2.208,1.896 2.604,2.25 0.396,0.354 10 false Time 0.521,0.521 0.875,1.573 0.354,1.052 10 false Input Shaft rpm 1.094,1.521 2.875,1.875 1.781,0.354 10 false Practical rpm Change Ratio 1.917,0.583 2.75,1.156 0.833,0.573 10 false Target rpm Change Ratio 1.573,5.042 2.417,5.729 0.844,0.688 10 false Clutch/Brake Pressure 2.76,6.167 4.083,6.521 1.323,0.354 10 false Solenoid Drive Signal 6.323,6.146 6.719,6.5 0.396,0.354 10 false Time 4.656,5.083 5.094,6.115 0.438,1.031 10 false Output Shaft Torque



c.

Clutch to Clutch Pressure Control

i.

This control is used for shifting from 4th to 5th gear and from 5th to 4th gear.


ii.

The ECM or TCM actuates shift solenoid valves SL1 and SL2 in accordance with various signals. The output from these shift solenoid valves acts directly on control valves B1 and C1 in order to regulate the line pressure that acts on the B1 brake and C1 clutch.


iii.

As a result, high response and excellent shift characteristics have been achieved.

X105622
2.167,3.052 2.427,3.052 2.427,3.052 2.625,3.417 true 6.094,3 5.833,3 5.833,3 5.635,3.406 true 2.167,3.74 2.427,3.74 2.427,3.74 2.625,4.094 true 6.125,3.677 5.865,3.677 5.865,3.677 5.667,4.073 true 0.167,0.927 2.708,1.271 2.542,0.344 10 false - Transmission Revolution Sensor (NT) 0.167,0.552 2.792,0.896 2.625,0.344 10 false - Transmission Revolution Sensor (SP2) 0.167,0.167 2.302,0.51 2.135,0.344 10 false - No. 1 ATF Temperature Sensor 0.167,1.344 3.01,1.688 2.844,0.344 10 false - Intake Mass Air Flow Meter Sub-assembly* 0.167,2.531 2.667,2.875 2.5,0.344 10 false - Engine Coolant Temperature Sensor 0.167,1.75 2.01,2.094 1.844,0.344 10 false - Throttle Position Sensor* 0.167,2.167 2.542,2.51 2.375,0.344 10 false - Accelerator Pedal Position Sensor 3.156,5.365 4.083,5.708 0.927,0.344 10 false Line Pressure 3.74,1.438 4.677,1.771 0.938,0.333 10 false ECM or TCM 1.26,2.979 2.146,3.323 0.885,0.344 10 false Shift Solenoid Valve (SL1) 6.167,2.896 7.042,3.583 0.875,0.688 10 false Shift Solenoid Valve (SL2) 1.25,3.677 2.156,4.01 0.906,0.333 10 false Clutch Control Valve 6.198,3.583 7.083,4.271 0.885,0.688 10 false Brake Control Valve 0.073,5.427 2.115,5.771 2.042,0.344 10 false *: Models with 1GR-FE engine



d.

Lock-up Timing Control

i.

The ECM or TCM operates the lock-up timing control in order to improve the fuel consumption performance in the top gear when the shift lever is in D or 4.

Lock-up Timing Control Operation
Gear Shift Lever Position
D 4
1st X X
2nd X X
3rd X X
4th X ○
5th ○ -

HINT:

○: Operates

X: Does not operate




e.

Flex Lock-up Clutch Control (Models with 1KD-FTV Engine)

i.

In the low-to-mid-speed range, this flex lock-up clutch control regulates the lock-up control solenoid assembly (SLU) to provide an intermediate mode between the on and off operations of the lock-up clutch in order to improve the energy transmitting efficiency in this range. As a result, the operating range of the lock-up clutch has been increased and fuel economy has been improved. The flex lock-up clutch control operates in 4th and 5th gears when the shift lever is in D, and in 4th gear when the shift lever is in 4.


ii.

Even when the vehicle is decelerating (the accelerator pedal is released), the flex lock-up clutch control operates. Therefore, the fuel-cut area of the engine has been expanded and fuel economy has been improved.

X102180
2.115,1.646 2.458,1.646 2.458,1.646 2.677,1.865 true 2.469,3.354 2.625,3.354 2.625,3.354 2.75,4.01 true 1.948,3.719 2.083,3.719 2.083,3.719 2.188,4.385 true 1.542,5.177 1.927,5.177 1.927,5.177 2.156,4.854 true 3.323,5.823 3.708,5.823 3.708,5.823 4.052,4.708 true 3.563,6.219 3.948,6.219 3.948,6.219 4.177,5.417 true 4.698,6.198 4.385,6.198 4.385,6.198 4.521,5.396 true 5.052,5.823 4.813,5.823 4.813,5.823 4.698,5.396 true 5.708,1.042 5.552,1.042 5.552,1.042 5.427,1.802 true 6.125,1.865 5.938,1.865 5.938,1.865 5.823,1.781 true 0.667,3.656 1.917,4.219 1.25,0.563 10 false Engine Coolant Temperature Sensor 0.969,3.26 2.479,3.615 1.51,0.354 10 false Throttle Position Sensor 0.302,5.094 1.563,5.76 1.26,0.667 10 false Crankshaft Position Sensor 5.792,0.948 6.688,1.615 0.896,0.667 10 false Engine Speed Signal 4.656,1.49 5.188,2.177 0.531,0.688 10 false Engine Speed 3.479,0.313 4.417,0.656 0.938,0.344 10 false ECM or TCM 5.167,2.156 6.115,2.5 0.948,0.344 10 false Vehicle Speed 0.958,5.719 3.344,6.063 2.385,0.344 10 false Transmission Revolution Sensor (NT) 2.177,6.115 3.635,6.458 1.458,0.344 10 false Lock-up Control Valve 5.083,5.729 6.719,6.073 1.635,0.344 10 false ATF Temperature Sensor 4.781,6.073 6.427,6.75 1.646,0.677 10 false Lock-up Control Solenoid Assembly (SLU) 6.188,1.792 7.021,2.792 0.833,1 10 false Transmission Revolution Signal 5.5,3.656 5.896,4 0.396,0.344 10 false Time 4.646,3.198 5.188,3.542 0.542,0.344 10 false Current 6.063,3.083 6.583,4.073 0.521,0.99 10 false Linear Solenoid Signal 0.469,1.542 2.198,2.208 1.729,0.667 10 false Accelerator Pedal Position Sensor

X102147
2.615,1.063 5.635,1.406 3.021,0.344 10 false : Lock-up operating range 0.271,0.313 3.292,0.656 3.021,0.344 10 false Flex Lock-up Operating Range 2.615,1.438 5.635,1.781 3.021,0.344 10 false : Flex lock-up operating range (acceleration) 2.615,1.792 5.635,2.135 3.021,0.344 10 false : Flex lock-up operating range (deceleration) 3.24,4.219 4.167,4.563 0.927,0.344 10 false Vehicle Speed 1.604,2.167 2,2.51 0.396,0.344 10 false Large 4.917,4.198 5.24,4.542 0.323,0.344 10 false High 0.833,2.979 1.948,3.656 1.115,0.677 10 false Accelerator Pedal Depressing Angle 0.583,3.979 1.698,4.667 1.115,0.688 10 false Accelerator Pedal is Released

Flex Lock-up Clutch Control Operation
Gear Shift Lever Position
D 4
1st X X
2nd X X
3rd X X
4th ○*1 ○*2
5th ○*1 -

HINT:

○: Operates

X: Does not operate

*1: Flex lock-up clutch control operates during acceleration and deceleration.

*2: Flex lock-up clutch control operates during deceleration.




f.

Artificial Intelligence-shift Control (AI-shift Control)

i.

The AI-shift control determines optimal transmission control based on input signals and automatically changes the shift pattern. As a result, a high caliber of transmission operation is achieved.


ii.

The AI-shift control includes a road condition support control and a driver's intention support control.


iii.

The AI-shift control is effected only with the shift lever in D, based on the accelerator pedal and brake operation data. The AI-shift control will be canceled when the shift lever is moved to a position other than D.

X105623
2.823,4.281 4.115,4.667 1.292,0.385 10 false Driver's Intention 0.844,0.729 1.781,1.063 0.938,0.333 10 false Input Signals 0.813,1.354 1.823,1.688 1.01,0.333 10 false Sensor Signal 0.656,1.833 1.719,2.49 1.063,0.656 10 false - Throttle Valve Opening Angle*1 0.656,3.177 1.792,3.51 1.135,0.333 10 false - Vehicle Speed 0.656,3.552 1.667,3.885 1.01,0.333 10 false - Engine Speed 0.667,3.906 1.677,4.24 1.01,0.333 10 false - Brake Signal 0.635,4.583 1.99,4.917 1.354,0.333 10 false Calculated by ECM 0.635,4.906 2.052,5.24 1.417,0.333 10 false Vehicle Acceleration 2.635,1.177 3.771,1.51 1.135,0.333 10 false AI-shift Control 2.771,1.521 3.906,1.854 1.135,0.333 10 false Road Condition 3,1.875 4.531,2.208 1.531,0.333 10 false Uphill/Downhill Driving 3.375,2.229 4.656,2.563 1.281,0.333 10 false Estimating Grade 2.604,2.635 3.073,2.948 0.469,0.313 10 false Small 3.927,2.896 4.344,3.219 0.417,0.323 10 false Large 3.021,3.219 4.625,3.552 1.604,0.333 10 false : Criterion acceleration 3.021,3.573 4.625,3.906 1.604,0.333 10 false : Actual acceleration 2.698,5.396 4.052,5.729 1.354,0.333 10 false - Vehicle Condition 2.708,4.75 3.917,5.406 1.208,0.656 10 false - Accelerator Pedal Operation 4.406,4.958 5.427,5.615 1.021,0.656 10 false Estimating Driver's Intention 6.083,0.74 6.781,1.719 0.698,0.979 10 false Basic Shift Pattern Control 6.073,2.646 6.688,3.99 0.615,1.344 10 false Road Condition Support Control 6.083,4.76 6.635,6.094 0.552,1.333 10 false Driver's Intention Support Control 0.646,2.521 1.875,3.177 1.229,0.656 10 false - Accelerator Pedal Depression Angle*2 0.396,6.177 2.573,6.51 2.177,0.333 10 false *1: Models with 1GR-FE engine 0.396,6.51 2.573,6.844 2.177,0.333 10 false *2: Models with 1KD-FTV engine


iv.

Under road condition support control, the ECM or TCM identifies the throttle valve opening angle, the accelerator pedal opening angle and the vehicle speed to determine whether the vehicle is being driven uphill or downhill. To achieve an optimal drive force while driving uphill, this control prevents the transmission from upshifting to 4th or 5th gear. To achieve an optimal engine braking effect while driving downhill, this control automatically downshifts the transmission to 4th or 3rd gear.

X102181
5.938,3.76 7.063,4.208 1.125,0.448 10 false With Control 5.438,3.885 5.938,4.333 0.5,0.448 10 false 5th 4.75,3.896 5.25,4.344 0.5,0.448 10 false 4th 5.927,3.26 7.052,3.708 1.125,0.448 10 false Without Control 4.292,3.875 4.792,4.323 0.5,0.448 10 false 3rd 3.135,3.896 3.635,4.344 0.5,0.448 10 false 4th 3.927,3.385 4.396,3.833 0.469,0.448 10 false 5th 2.854,3.385 3.354,3.833 0.5,0.448 10 false 4th 2.448,3.375 2.948,3.823 0.5,0.448 10 false 5th 2.083,3.885 2.583,4.333 0.5,0.448 10 false 3rd 2.083,3.375 2.583,3.823 0.5,0.448 10 false 3rd 1.521,3.906 2.021,4.354 0.5,0.448 10 false 4th 1.76,3.385 2.26,3.833 0.5,0.448 10 false 5th 1.323,3.385 1.823,3.833 0.5,0.448 10 false 4th 0.708,3.896 1.208,4.344 0.5,0.448 10 false 5th 0.708,3.375 1.208,3.823 0.5,0.448 10 false 5th 4.76,1.25 6.281,1.698 1.521,0.448 10 false Brake Operating


v.

The driver's intention support control is estimated based on the accelerator pedal operation and vehicle condition.




FAIL-SAFE


a.

The fail-safe function minimizes the loss of operability when an abnormality occurs in a sensor or a solenoid.

Fail-safe Control List
Malfunction Part Function
Transmission Revolution Sensor (NT)
·

During a transmission revolution sensor (NT) malfunction, shift control is effected based on the transmission revolution sensor (SP2) or speed sensor (SPD1) signal.

·

During a transmission revolution sensor (NT) malfunction, upshifting to 5th, AI-shift , lock-up control and flex lock-up clutch control are prohibited.


Transmission Revolution Sensor (SP2)
·

During a transmission revolution sensor (SP2) malfunction, shift control is effected based on the transmission revolution sensor (NT) or speed sensor (SPD1) signal.

·

During a transmission revolution sensor (SP2) malfunction, upshifting to 5th, AI-shift , lock-up control and flex lock-up clutch control are prohibited.


No. 1 ATF Temperature Sensor (THO1) During a No. 1 ATF temperature sensor malfunction, upshifting to 5th, lock-up control and flex lock-up clutch control are prohibited.
Shift Solenoid Valves S1, S2, and SR
·

When one of the shift solenoid valves listed left malfunctions, current to the failed shift solenoid valve is cut off.

·

Shift control is changed to a fail-safe mode to shift gears using the normal shift solenoid valves to allow continued driving.


Shift Solenoid Valves SL1 and SL2 During a shift solenoid valve SL1 or SL2 malfunction, upshifting to 5th, lock-up control and flex lock-up clutch control are prohibited.
Line Pressure Control Solenoid Assembly (SLT) During a line pressure control solenoid assembly (SLT) malfunction, the current to the shift solenoid valve is stopped. Because this stops line pressure optimal control, the shift shock will increase. However, shifting is effected based on normal clutch pressure control.
Lock-up Control Solenoid Assembly (SLU) During a lock-up control solenoid assembly (SLU) malfunction, the current to the shift solenoid valve is stopped. Because this stops lock-up control and flex lock-up clutch control, fuel economy decreases.



DIAGNOSIS


a.

When the ECM or TCM detects a malfunction, it makes a diagnosis and memorizes the failed section. Furthermore, the ECM or TCM illuminates or blinks the MIL in the combination meter assembly to inform the driver.


b.

The ECM or TCM will also store the Diagnostic Trouble Codes (DTCs) of the malfunctions.


c.

The DTCs can be read by connecting an intelligent tester II to the DLC3.


d.

For details, refer to the Repair Manual.