FUNCTION OF MAIN COMPONENTS
| Component | Function | |
|---|---|---|
| Brake Actuator Assembly | Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders. | |
| Motor Relay (Built-into Skid Control ECU) | Supplies power to the pump motor. | |
| Solenoid Relay (Built-into Skid Control ECU) | Supplies power to the solenoid valves. | |
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | |
| Deceleration Sensor*1 | Detects the vehicle's acceleration in forward and reverse. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Parking Brake Switch | Detects the parking brake lever status. | |
| Brake Fluid Level Warning Switch | Detects the brake fluid level. | |
| Transfer Indicator Switch (L4 Position)*2 | Detects the L4 position condition. | |
| Transfer Indicator Switch (4WD Position)*3 | Detects the transfer drive mode. | |
| A.D.D. Position Switch*4 | Detects the A.D.D. shift actuator operating condition. | |
| Combination Meter Assembly | ABS Warning Light | Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS. |
| Skid Control ECU | Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator. | |
*1: 2WD PreRunner and 4WD models
*2: 4WD models
*3: 4WD models without A.D.D.
*4: Models with A.D.D.
| Component | Function | |
|---|---|---|
| Brake Actuator Assembly | Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders. | |
| Master Cylinder Pressure Sensor (Built-into Brake Actuator) | Detects the master cylinder pressure. | |
| Motor Relay (Built-into Skid Control ECU) | Supplies power to the pump motor. | |
| Motor Cut Relay (Built into Skid Control ECU) | Cuts the power to the pump motor when the motor relay malfunctions. | |
| Solenoid Relay (Built-into Skid Control ECU) | Supplies power to the solenoid valves. | |
| Speed Sensors | Detect the wheel speed of each of the 4 wheels. | |
| Yaw Rate Sensor Assembly | ·
Detects the vehicle's yaw rate. ·
Detects the vehicle's longitudinal and lateral acceleration. |
|
| Steering Angle Sensor | Detects the steering direction and angle of the steering wheel. | |
| Stop Light Switch Assembly | Detects the brake pedal depressing signal. | |
| Parking Brake Switch | Detects the parking brake lever status. | |
| Brake Pedal Load Sensing Switch | Detects the brake pedal depressing force. | |
| VSC OFF Switch | Enables the driver to select "Normal Mode", " TRC OFF Mode", or "VSC OFF Mode". | |
| Park/Neutral Position Switch Assembly*1 | Detects the shift lever position. | |
| Transfer Indicator Switch (L4 Position)*2 | Detects the L4 position condition. | |
| A.D.D. Position Switch*2 | Detects the A.D.D. shift actuator operating condition. | |
| Combination Meter Assembly | ABS Warning Light | Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS. |
| Brake System Warning Light | ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD. ·
Illuminates to alert the driver when the brake fluid level is low. ·
Illuminates to inform the driver when the parking brake lever is pulled up. |
|
| Slip Indicator Light | ·
Blinks to inform the driver when the TRC or VSC is operational. ·
Illuminates to inform the driver that the TRC OFF mode or VSC OFF mode is entered using the VSC OFF switch. ·
Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC and/or VSC. |
|
| VSC OFF Indicator Light | ·
Illuminates to inform the driver when VSC OFF mode is selected. ·
Blinks to alert the driver when the skid control ECU detects a malfunction and determines that the TRC and/or VSC is not available. |
|
| Skid Control ECU | Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator. | |
| ECM | ·
Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU. ·
Based on the signals from the skid control ECU, controls the engine output. |
|
*1: Models with automatic transmission
*2: 4WD models
SYSTEM CONTROL
Models without VSC
| Control | Outline |
|---|---|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
Models with VSC
| Control | Outline |
|---|---|
| Anti-lock Brake System (ABS) | The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface. |
| Electronic Brake Force Distribution (EBD) | The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior. |
| Brake Assist | ·
The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance. ·
If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force. |
| Traction Control (TRC) | The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. |
| Vehicle Stability Control (VSC) | The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or a strong rear wheel skid, either of which may occur while cornering. |
Anti-lock Brake System (ABS)
The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.
| *A | Models with ABS | *B | Models without ABS |
| *a | Brake Operation | - | - |
Electronic Brake Force Distribution (EBD)
This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.
During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.
|
Brake Force |
|
Control Moment |
Brake Assist
In the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.
Traction Control (TRC)
The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Together with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.
| *A | Models without TRC | *B | Models with TRC |
| *1 | ECM
·
Engine Output Control |
*2 | Brake Actuator Assembly
·
Hydraulic Brake Control |
| *a | Brake Slipping Drive Wheel | - | - |
|
Slippery Surface | - | - |
Vehicle Stability Control (VSC)
The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below:
| *a | Front Wheel Skid Tendency (Understeer) | *b | Rear Wheel Skid Tendency (Oversteer) |
To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate, and the vehicle's lateral acceleration, which are then calculated by the skid control ECU.
Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (which is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.
| *a | Actual Locus of Travel (Actual Yaw Rate) | *b | Locus of Travel Based on Target Yaw Rate |
Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.
| *a | Direction of Travel of Vehicle's Center of Gravity | *b | Movement of Vehicle |
|
Slip Angle | - | - |
When the skid control ECU determines that the vehicle exhibits a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of the front or rear wheels to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.
When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the front wheel on the outer circle of the turn and the rear wheels in order to help restrain the front wheel skid tendency.
|
Brake Force |
|
Control Moment |
When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front wheel on the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.
|
Brake Force |
|
Control Moment |
FUNCTION
VSC OFF Switch
The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.
The VSC OFF switch can select 3 modes (Normal mode, TRC OFF mode, and VSC OFF mode).
Briefly pressing the VSC OFF switch in Normal mode selects the TRC OFF mode.
Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the VSC OFF mode, disabling the TRC and VSC functions.
Briefly pressing the VSC OFF switch in the TRC OFF mode or VSC OFF mode or turning the ignition switch off returns to the Normal mode.
| *a | Normal Mode | *b | TRC OFF Mode |
| *c | VSC OFF Mode | - | - |
|
VSC OFF Switch Operation (Briefly Press) |
|
VSC OFF Switch Operation (Press and Hold for 3 Seconds or More) |
The operation of the brake control functions and the illumination state of the respective indicator lights in each mode are as follows:
| Transfer Drive Mode | VSC OFF Mode | Brake Control Function | Slip Indicator Light | VSC OFF Indicator Light | |
|---|---|---|---|---|---|
| TRC | VSC |
|
|
||
| H2 | Normal Mode | Controllable | Controllable | - | - |
| TRC OFF Mode | Not Controllable*1 | Controllable | Illuminates | - | |
| VSC OFF Mode | Not Controllable | Not Controllable*2 | Illuminates | Illuminates | |
| H4 | Normal Mode | Controllable | Controllable | - | - |
| TRC OFF Mode | Not Controllable*1 | Controllable | Illuminates | - | |
| VSC OFF Mode | Not Controllable | Not Controllable*2 | Illuminates | Illuminates | |
| L4 | Normal Mode | Controllable | Not Controllable | - | Illuminates |
| VSC OFF Mode | Not Controllable | Not Controllable | Illuminates | Illuminates | |
*1: When the vehicle exceeds a determined speed [approximately 50 km/h (31 mph)], Normal mode will operate.
*2: When the vehicle is braking or the yaw rate is large, the VSC will operate even in the VSC OFF mode. (In this case, the engine output is not controlled.)
FAIL-SAFE
If a failure occurs in the skid control ECU, sensors, or brake actuator, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.
DIAGNOSIS
If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.
This system has a sensor signal check (test mode) function.
For details of DTC and check function, refer to the Repair Manual.