Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.10–2014.10
NM1840EF _51 Engine / Hybrid System _010301 2TR-FE ENGINE MECHANICAL _0055226 ENGINE UNIT GE GENERAL F

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 2TR-FE engine is an in-line 4-cylinder, 2.7-liter, 16-valve DOHC engine.


b.

On this engine, the Variable Valve Timing-intelligent (VVT-i) system, Electronic Throttle Control System-intelligent (ETCS-i), and air injection system are used. These control functions have been optimized to further improve engine performance and fuel economy, and to reduce exhaust emissions.



SPECIFICATION


No. of Cyls. and Arrangement 4-cylinder, In-line
Valve Mechanism 16-valve DOHC, Chain Drive (with VVT-i)
Combustion Chamber Pentroof Type
Manifolds Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI)
Ignition System Direct Ignition System (DIS)
Displacement 2694 cm3 (164.4 cu. in.)
Bore x Stroke 95.0 mm x 95.0 mm (3.74 in. x 3.74 in.)
Compression Ratio 9.6 : 1
Max. Output [SAE-NET] 116 kW @ 5200 rpm*2
118 kW @ 5200 rpm*3
Max. Torque [SAE-NET] 240 N*m @ 3800 rpm*2
241 N*m @ 3800 rpm*3
Valve Timing Intake Open 0° to 35° BTDC
Closed 64° to 29° ABDC
Exhaust Open 44° BBDC
Closed 8° ATDC
Spark Plug Manufacturer DENSO
Type K20HR-U11
Plug Gap 1.0 mm to 1.1 mm (0.0394 in. to 0.0433 in.)
Firing Order 1 - 3 - 4 - 2
Research Octane Number 91 or higher
Emission Regulation EURO 4*4
EURO 3*5
EURO 2*6
Engine Service Mass (Reference)*1 157 kg (346 lb)

HINT:

*1: Weight shows the figure with oil and coolant fully filled.

*2: Models compliant with EURO 4 emission regulations

*3: Except models compliant with EURO 4 emission regulations

*4: Models for Central and South America (TGN26L-PRMSGK, TGN36L-PRMDKG and TGN36L-PRMSKG)

*5: Models for Central and South America (TGN26L-PRMDKG and TGN36L-TRMDKG) and General Countries (TGN26L-HRMDK)

*6: Models for Colombia, Ecuador, ANCOM and General Countries (TGN26L-HRMSK)


W105117E02
2.333,4.083 2.719,4.365 0.385,0.281 10 false 1000 2.792,4.083 3.177,4.365 0.385,0.281 10 false 2000 3.219,4.083 3.604,4.365 0.385,0.281 10 false 3000 3.667,4.083 4.052,4.365 0.385,0.281 10 false 4000 4.125,4.083 4.51,4.365 0.385,0.281 10 false 5000 4.552,4.083 4.938,4.365 0.385,0.281 10 false 6000 4.948,0.875 5.385,1.073 0.438,0.198 10 false 130 4.948,1.333 5.385,1.531 0.438,0.198 10 false 110 4.948,1.771 5.385,1.969 0.438,0.198 10 false 90 4.948,2.219 5.385,2.417 0.438,0.198 10 false 70 4.948,2.646 5.385,2.844 0.438,0.198 10 false 50 4.948,3.104 5.385,3.302 0.438,0.198 10 false 30 4.948,3.542 5.385,3.74 0.438,0.198 10 false 10 4.948,3.333 5.385,3.531 0.438,0.198 10 false 20 4.948,2.885 5.385,3.083 0.438,0.198 10 false 40 4.948,2.438 5.385,2.635 0.438,0.198 10 false 60 4.948,1.99 5.385,2.188 0.438,0.198 10 false 80 4.948,1.552 5.385,1.75 0.438,0.198 10 false 100 4.948,1.115 5.385,1.313 0.438,0.198 10 false 120 4.948,3.781 5.385,3.979 0.438,0.198 10 false 0 2.01,1.563 2.333,1.771 0.323,0.208 10 false 260 2.01,1.792 2.333,2 0.323,0.208 10 false 240 2.01,2.01 2.333,2.219 0.323,0.208 10 false 220 2.01,2.229 2.333,2.438 0.323,0.208 10 false 200 2.01,2.448 2.333,2.656 0.323,0.208 10 false 180 3,4.406 4.313,4.75 1.313,0.344 10 false Engine Speed (rpm) 5.646,2.24 6.198,2.552 0.552,0.313 10 false Output 4.833,0.51 5.219,0.802 0.385,0.292 10 false (kW) 2.031,1.208 2.563,1.563 0.531,0.354 10 false (N*m) 1.354,2.031 1.896,2.323 0.542,0.292 10 false Torque 0.74,0.302 4.188,0.625 3.448,0.323 10 false : Models compliant with EURO 4 emission regulations 0.729,0.594 4.781,0.917 4.052,0.323 10 false : Except models compliant with EURO 4 emission regulations


MAIN FEATURES


a.

This engine has been able to achieve the following performance features through the use of the items listed below:

i.

High performance and fuel economy


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions

Item (1) (2) (3) (4) (5)
Engine Proper A cylinder head cover made of plastic is used. - ○ ○ - -
A taper squish shape is used for the combustion chamber. ○ - - - ○
2 balance shafts are used. - ○ - - -
The piston skirt is coated with resin. ○ ○ - - -
A No. 1 oil pan made of aluminum alloy is used. ○ ○ ○ - -
Valve Mechanism Timing chains and chain tensioners are used. ○ - ○ ○ -
Valve lash adjuster assemblies are used. ○ ○ - ○ ○
Valve rocker arm sub-assemblies are used. ○ - - - ○
Intake and Exhaust System An intake manifold made of plastic is used. - - ○ - -
A linkless-type throttle body is used. - - ○ ○ -
A Three-Way Catalysts (TWCs) are used. - - - - ○
Fuel System Long nozzle, 12-hole type fuel injector assemblies are used to improve the atomization of fuel. ○ - - - ○
Quick connectors are used to connect the fuel hose with the fuel pipe. - - - ○ -
Ignition System Long-reach type spark plugs are used. ○ - - - -
Serpentine Belt Drive System A serpentine belt drive system is used. - ○ ○ ○ -
Engine Control System The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
The Direct Ignition System (DIS) makes ignition timing adjustment unnecessary. ○ - - ○ ○
The Variable Valve Timing-intelligent (VVT-i) system is used. ○ - - - ○
An air injection system is used.* - - - - ○

*: Models compliant with EURO 3 and EURO 4 emission regulations