Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL SYSTEM › from 2013.10
NM1840EF _54 Brake _010353 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0055285 BRAKE CONTROL SYSTEM CO CONTROL F

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL SYSTEM  CONTROL  BRAKE CONTROL  


FUNCTION OF MAIN COMPONENTS


Models without VSC
Component Function
Brake Actuator Assembly Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders.
Motor Relay (Built-into Skid Control ECU) Supplies power to the pump motor.
Solenoid Relay (Built-into Skid Control ECU) Supplies power to the solenoid valves.
Speed Sensors Detect the wheel speed of each of the 4 wheels.
Deceleration Sensor*1 Detects the vehicle's acceleration in forward and reverse.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Detects the parking brake lever status.
Brake Fluid Level Warning Switch Detects the brake fluid level.
Transfer Indicator Switch (L4 Position)*2 Detects the L4 position condition.
Transfer Indicator Switch (4WD Position)*3 Detects the transfer drive mode.
A.D.D. Position Switch*4 Detects the A.D.D. shift actuator operating condition.
Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator.

*1: 2WD PreRunner and 4WD models

*2: 4WD models

*3: 4WD models without A.D.D.

*4: Models with A.D.D.


Models with VSC
Component Function
Brake Actuator Assembly Changes the fluid path based on the signals from the skid control ECU during the operation of the brake control system functions, in order to control the fluid pressure applied to the wheel cylinders.
Master Cylinder Pressure Sensor (Built-into Brake Actuator) Detects the master cylinder pressure.
Motor Relay (Built-into Skid Control ECU) Supplies power to the pump motor.
Motor Cut Relay (Built into Skid Control ECU) Cuts the power to the pump motor when the motor relay malfunctions.
Solenoid Relay (Built-into Skid Control ECU) Supplies power to the solenoid valves.
Speed Sensors Detect the wheel speed of each of the 4 wheels.
Yaw Rate Sensor Assembly
·

Detects the vehicle's yaw rate.

·

Detects the vehicle's longitudinal and lateral acceleration.


Steering Angle Sensor Detects the steering direction and angle of the steering wheel.
Stop Light Switch Assembly Detects the brake pedal depressing signal.
Parking Brake Switch Detects the parking brake lever status.
Brake Pedal Load Sensing Switch Detects the brake pedal depressing force.
VSC OFF Switch Enables the driver to select "Normal Mode", " TRC OFF Mode", or "VSC OFF Mode".
Park/Neutral Position Switch Assembly*1 Detects the shift lever position.
Transfer Indicator Switch (L4 Position)*2 Detects the L4 position condition.
A.D.D. Position Switch*2 Detects the A.D.D. shift actuator operating condition.
Combination Meter Assembly ABS Warning Light Lights up to alert the driver when the skid control ECU detects a malfunction in the ABS.
Brake System Warning Light
·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD.

·

Illuminates to alert the driver when the brake fluid level is low.

·

Illuminates to inform the driver when the parking brake lever is pulled up.


Slip Indicator Light
·

Blinks to inform the driver when the TRC or VSC is operational.

·

Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRC and/or VSC.


TRC OFF Indicator Light
·

Illuminates to inform the driver when TRC OFF mode is selected.

·

Illuminates together with the VSC OFF indicator light to inform the driver when VSC OFF mode is selected.


VSC OFF Indicator Light Illuminates to inform the driver when VSC OFF mode is selected.
Skid Control ECU Judges the vehicle driving condition based on the signals from each sensor, and sends the brake control signals to the brake actuator.
ECM
·

Sends the throttle position signal, accelerator pedal position signal, engine speed signal etc., to the skid control ECU.

·

Based on the signals from the skid control ECU, controls the engine output.



*1: Models with automatic transmission

*2: 4WD models



SYSTEM CONTROL


a.

Models without VSC

Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.


b.

Models with VSC

Control Outline
Anti-lock Brake System (ABS) The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.
Electronic Brake Force Distribution (EBD) The EBD control utilizes ABS, achieving proper brake force distribution between the front and rear wheels in accordance with the driving conditions. In addition, during braking while cornering, it also controls the brake forces of the right and left wheels, helping maintain vehicle behavior.
Brake Assist
·

The primary purpose of brake assist is to provide an auxiliary brake force to assist a driver who cannot generate a large brake force during emergency braking, thus helping ensure the vehicle's braking performance.

·

If the brake booster malfunctions and the skid control ECU judges that the brake pedal force applied by the driver is not sufficient to ensure adequate braking force, brake assist is used to enhance the braking force.


Traction Control (TRC) The TRC helps restrain the slippage of the drive wheels if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.
Vehicle Stability Control (VSC) The VSC helps restrain sideways slippage of the vehicle during a strong front wheel skid or a strong rear wheel skid, either of which may occur while cornering.


c.

Anti-lock Brake System (ABS)

i.

The ABS prevents the wheels from locking during sudden braking or braking on a slippery surface. This provides the proper braking force when the vehicle slips, thus ensuring vehicle stability and excellent braking performance.

X105299
1.385,0.99 1.771,1.354 0.385,0.365 12 false *A: 1.385,2.323 1.771,2.688 0.385,0.365 12 false *B: 4.583,0.958 4.969,1.323 0.385,0.365 10 false *a
*A Models with ABS *B Models without ABS
*a Brake Operation - -




d.

Electronic Brake Force Distribution (EBD)

i.

This function controls the brake force that acts on the rear wheels in accordance with the changes in the vehicle conditions such as load factors or deceleration, in order to ensure excellent braking performance.

X105300
2.365,2.531 2.156,2.531 2.156,2.531 2.156,2.344 true 1.833,1.563 1.469,1.563 1.469,1.563 1.698,2.406 true 5.188,2.521 4.979,2.521 4.979,2.521 4.979,2.333 true 4.688,1.448 4.323,1.448 4.323,1.448 4.719,2.177 true 0.323,2.052 1.031,2.823 0.708,0.771 10 false Rear Brake Force 3.354,2.01 4.073,2.781 0.719,0.771 10 false Rear Brake Force 1.875,1.438 3.802,1.813 1.927,0.375 10 false Ideal Brake Force Distribution 2.417,2.427 3.635,2.823 1.219,0.396 10 false EBD Control 1.49,2.885 2.813,3.271 1.323,0.385 10 false Front Brake Force 1.438,3.323 3.042,3.708 1.604,0.385 10 false Without Load in Rear 4.531,2.875 5.854,3.26 1.323,0.385 10 false Front Brake Force 4.531,3.292 6.135,3.677 1.604,0.385 10 false With Load in Rear 4.75,1.354 6.708,1.75 1.958,0.396 10 false Ideal Brake Force Distribution 5.25,2.417 6.469,2.813 1.219,0.396 10 false EBD Control


ii.

During cornering braking, this function controls the brake force that acts on the left and right wheels in accordance with the vehicle conditions at that time. This ensures vehicle stability and excellent braking performance.

X105301

V100135

Brake Force
V100136

Control Moment



e.

Brake Assist

i.

In the brake assist, the skid control ECU calculates the speed and the amount of the brake pedal application based on the signals from the master cylinder pressure sensor and then determines the intention of the driver to make an emergency brake application. If the skid control ECU determines that the driver intends to make an emergency brake application, this function activates the brake actuator to increase the brake fluid pressure, which increases the brake force.

X105302
0.865,2.917 3.656,3.26 2.792,0.344 10 false Fluid Pressure Increased by Brake Actuator 0.99,0.542 2.188,0.865 1.198,0.323 10 false Skid Control ECU 1.073,1.333 2.167,1.646 1.094,0.313 10 false Brake Actuator 4.948,2.177 6.344,2.521 1.396,0.344 10 false Without Brake Assist 5.073,1.458 6.302,1.802 1.229,0.344 10 false With Brake Assist 5.5,2.781 5.906,3.125 0.406,0.344 10 false Time 4.083,0.833 4.479,1.49 0.396,0.656 10 false Brake Force



f.

Traction Control (TRC)

i.

The TRC helps prevent the drive wheels from slipping if the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface. Together with the hydraulic brake control of the drive wheels, the skid control ECU makes a request to the ECM to effect engine output control. This produces the drive force that suits the driving conditions, in order to ensure the proper start-off acceleration.

Driving on Road with Different Surface Friction Characteristics
X105303
5.01,1.365 4.521,1.365 false 5.01,0.948 4.521,0.948 false 6.125,0.677 5.469,0.677 true 6.125,1.906 5.469,1.906 true 4.365,1.281 4.719,1.531 0.354,0.25 10 false *2 2.667,0.271 3.021,0.521 0.354,0.25 12 false *B: 1.073,0.292 1.427,0.542 0.354,0.25 12 false *A: 4.365,0.865 4.719,1.115 0.354,0.25 10 false *1 6.146,0.563 6.5,0.813 0.354,0.25 10 false *a 6.146,1.771 6.5,2.021 0.354,0.25 10 false *a
*A Models without TRC *B Models with TRC
*1 ECM
·

Engine Output Control


*2 Brake Actuator Assembly
·

Hydraulic Brake Control


*a Brake Slipping Drive Wheel - -
V100145

Slippery Surface - -




g.

Vehicle Stability Control (VSC)

i.

The following are 2 examples that can be considered circumstances in which the tires exceed their lateral grip limit. The VSC is designed to help control the vehicle behavior by controlling the engine output and the brakes at each wheel when the vehicle is under one of the conditions indicated below:

X105304
1.938,3.031 2.552,3.396 0.615,0.365 10 false *a 5.031,3.031 5.646,3.396 0.615,0.365 10 false *b
*a Front Wheel Skid Tendency (Understeer) *b Rear Wheel Skid Tendency (Oversteer)



ii.

To determine the condition of the vehicle, sensors detect the steering angle, vehicle speed, vehicle's yaw rate, and the vehicle's lateral acceleration, which are then calculated by the skid control ECU.


iii.

Whether or not the vehicle is experiencing a front wheel skid is determined by the difference between the target yaw rate and the vehicle's actual yaw rate. When the vehicle's actual yaw rate is smaller than the target yaw rate (which is determined based on the vehicle speed and steering angle) that should be generated when the driver operates the steering wheel, it means the vehicle is making a turn at a greater angle than the target locus of travel. Thus, the skid control ECU determines that there is a large front wheel skid tendency.

X105305
3.698,0.094 4.052,0.427 0.354,0.333 10 false *a 4.688,0.854 5.042,1.188 0.354,0.333 10 false *b
*a Actual Locus of Travel (Actual Yaw Rate) *b Locus of Travel Based on Target Yaw Rate



iv.

Whether or not the vehicle is experiencing a rear wheel skid is determined by the values of the vehicle's slip angle and the vehicle's slip angular velocity (time-dependent changes in the vehicle's slip angle). When the vehicle's slip angle is large, and the slip angular velocity is also large, the skid control ECU determines that the vehicle has a large rear wheel skid tendency.

X105306
3.563,0.083 4.052,0.479 0.49,0.396 10 false *a 3.99,0.115 4.479,0.51 0.49,0.396 10 false *b
*a Direction of Travel of Vehicle's Center of Gravity *b Movement of Vehicle
V100136

Slip Angle - -



v.

When the skid control ECU determines that the vehicle exhibits a tendency to experience a front wheel skid or a rear wheel skid, it decreases the engine output and applies the brakes of the front or rear wheels to control the vehicle's yaw moment. The basic operation of the VSC is described below. However, the control method differs depending on the vehicle's characteristics and driving conditions.


vi.

When the skid control ECU determines that there is a large front wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. The skid control ECU controls the engine output and applies the brakes of the front wheel on the outer circle of the turn and the rear wheels in order to help restrain the front wheel skid tendency.

X105307

V100135

Brake Force
V100136

Control Moment


vii.

When the skid control ECU determines that there is a large rear wheel skid tendency, it takes countermeasures in accordance with the extent of that tendency. It applies the brakes of the front wheel on the outer circle of the turn, and generates an outward moment of inertia in the vehicle, in order to restrain the rear wheel skid tendency. Along with the reduction in the vehicle speed caused by the braking force, excellent vehicle stability is ensured. In some cases, the skid control ECU applies the brake of the rear wheels, as necessary.

X105308

V100135

Brake Force
V100136

Control Moment




FUNCTION


a.

VSC OFF Switch

i.

The operation of the VSC and TRC functions can be stopped by the VSC OFF switch. While the vehicle is running off the shoulder of the road or running on a dirt road, the engine output control is stopped to maintain drive torque.


ii.

The VSC OFF switch can select 3 modes (Normal mode, TRC OFF mode, and VSC OFF mode).


iii.

Briefly pressing the VSC OFF switch in Normal mode selects the TRC OFF mode.


iv.

Pressing and holding the VSC OFF switch for 3 seconds or more with the vehicle stopped selects the VSC OFF mode, disabling the TRC and VSC functions.


v.

Briefly pressing the VSC OFF switch in the TRC OFF mode or VSC OFF mode or turning the ignition switch off returns to the Normal mode.

X105309
3.51,0.563 3.854,0.854 0.344,0.292 10 false *a 4.917,1.823 5.26,2.115 0.344,0.292 10 false *c 2.083,1.802 2.427,2.094 0.344,0.292 10 false *b
*a Normal Mode *b TRC OFF Mode
*c VSC OFF Mode - -
V100136

VSC OFF Switch Operation (Briefly Press)
V100135

VSC OFF Switch Operation (Press and Hold for 3 Seconds or More)



vi.

The operation of the brake control functions and the illumination state of the respective indicator lights in each mode are as follows:

Transfer Drive Mode VSC OFF Mode Brake Control Function Indicator Light
TRC VSC TRC OFF Indicator Light VSC OFF Indicator Light
H2 Normal Mode Controllable Controllable - -
TRC OFF Mode Not Controllable*1 Controllable Illuminates -
VSC OFF Mode Not Controllable Not Controllable*2 Illuminates Illuminates
H4 Normal Mode Controllable Controllable - -
TRC OFF Mode Not Controllable*1 Controllable Illuminates -
VSC OFF Mode Not Controllable Not Controllable*2 Illuminates Illuminates
L4 Normal Mode Controllable Not Controllable - Illuminates
VSC OFF Mode Not Controllable Not Controllable Illuminates Illuminates

HINT:

*1: When the vehicle exceeds a determined speed [approximately 50 km/h (31 mph)], Normal mode will operate.

*2: When the vehicle is braking or the yaw rate is large, the VSC will operate even in the VSC OFF mode. (In this case, the engine output is not controlled.)





FAIL-SAFE


a.

If a failure occurs in the skid control ECU, sensors, or brake actuator, the system continues effecting brake control by excluding the failed area and using only the areas that are operating normally.



DIAGNOSIS


a.

If the skid control ECU detects a malfunction in the brake control system, the warning lights or indicator light illuminate. At the same time, a Diagnostic Trouble Code (DTC) is stored in the memory of the skid control ECU.


b.

This system has a sensor signal check (test mode) function.


c.

For details of DTC and check function, refer to the Repair Manual.