CONSTRUCTION
Models without VSC
The brake actuator assembly consists of an actuator portion and skid control ECU.
| *1 | Skid Control ECU | *2 | Actuator Portion |
The actuator portion consists of 3 pressure holding solenoid valves, 3 pressure reduction solenoid valves, 2 pumps and 2 reservoirs.
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *3 | Pump | *4 | Reservoir |
| *5 | Brake Control Valve | - | - |
| *a | From Master Cylinder | *b | Front Brake LH |
| *c | Front Brake RH | *d | Rear Brake LH |
| *e | Rear Brake RH | - | - |
Models with VSC
The brake actuator assembly consists of an actuator portion and skid control ECU.
| *1 | Skid Control ECU | *2 | Actuator Portion |
The actuator portion consists of 2 master cylinder cut solenoid valves, 4 pressure holding solenoid valves, 4 pressure reduction solenoid valves, 2 pumps, 2 reservoirs, and a master cylinder pressure sensor.
| *1 | Master Cylinder Pressure Sensor | *2 | Master Cylinder Cut Solenoid Valve |
| *3 | Pressure Holding Solenoid Valve | *4 | Pressure Reduction Solenoid Valve |
| *5 | Pump | *6 | Reservoir |
| *a | From Master Cylinder | *b | Rear Brake LH |
| *c | Rear Brake RH | *d | Front Brake LH |
| *e | Front Brake RH | - | - |
OPERATION
ABS (Models without VSC)
Based on the signals received from the 4 speed sensors and deceleration sensor, the skid control ECU calculates the speed of each wheel and the deceleration, and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *3 | Port A | *4 | Port B |
| *a | Pressure Increase Mode | *b | Pressure Holding Mode |
| *c | Pressure Reduction Mode | *d | To Brake Caliper or Wheel Cylinder |
| *e | From Brake Caliper or Wheel Cylinder | - | - |
| Pressure Mode | Increase Mode | Holding Mode | Reduction Mode |
|---|---|---|---|
| Pressure Holding Solenoid Valve (Port A) | Off (Open) | On (Closed) | ← |
| Pressure Reduction Solenoid Valve (Port B) | Off (Closed) | ← | On (Open) |
| Wheel Cylinder Pressure | Increases | Holds | Reduces |
ABS and EBD (Models with VSC)
Based on the signals received from the 4 speed sensors and yaw rate sensor assembly, the skid control ECU calculates the speed of each wheel and deceleration, and checks the wheel slipping conditions. In accordance with the slipping condition, the skid control ECU controls each solenoid valve in the brake actuator in order to adjust the fluid pressure of each wheel cylinder in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes.
| *1 | Pressure Holding Solenoid Valve | *2 | Pressure Reduction Solenoid Valve |
| *3 | Port A | *4 | Port B |
| *a | Pressure Increase Mode | *b | Pressure Holding Mode |
| *c | Pressure Reduction Mode | *d | To Brake Caliper or Wheel Cylinder |
| *e | From Brake Caliper or Wheel Cylinder | - | - |
| Pressure Mode | Increase Mode | Holding Mode | Reduction Mode |
|---|---|---|---|
| Pressure Holding Solenoid Valve (Port A) | Off (Open) | On (Closed) | ← |
| Pressure Reduction Solenoid Valve (Port B) | Off (Closed) | ← | On (Open) |
| Wheel Cylinder Pressure | Increases | Holds | Reduces |
Brake Assist
In the event of emergency braking, the skid control ECU determines the driver's intention based on the speed of the pressure increase in the master cylinder determined by the master cylinder pressure sensor signal. If the skid control ECU judges the need for additional brake assist, pressure is generated by the pump in the brake actuator and directed to the wheel cylinder to apply a large amount of fluid pressure.
| Item | Brake Assist Not Activated | Brake Assist Activated | ||
|---|---|---|---|---|
| Pump | Off | On | ||
| Master Cylinder Cut Solenoid Valve | (1) | Port (A) | Off (Open) | On* |
| (2) | Port (B) | Off (Open) | On* | |
| Pressure Holding Solenoid Valve | (3) | Port (C) | Off (Open) | ← |
| (4) | Port (D) | Off (Open) | ← | |
| (5) | Port (E) | Off (Open) | ← | |
| (6) | Port (F) | Off (Open) | ← | |
| Pressure Reduction Solenoid Valve | (7) | Port (G) | Off (Closed) | ← |
| (8) | Port (H) | Off (Closed) | ← | |
| (9) | Port (I) | Off (Closed) | ← | |
| (10) | Port (J) | Off (Closed) | ← | |
*: The solenoid valve switches the hydraulic pressure between open and closed in accordance with the operating conditions by adjusting continually.
TRC
The fluid pressure generated by the pump is regulated by the master cylinder cut solenoid valve to the required pressure. Thus, the wheel cylinders of the drive wheels are controlled in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes to control the slippage of the drive wheels. The pressure holding solenoid valve and the pressure reduction solenoid valve are turned on or off in accordance with the ABS and EBD operation patterns.
| Item | Not Activated | TRC Operation | |||||
|---|---|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||||
| Pump | Off | On | ← | ← | |||
| Master Cylinder Cut Solenoid Valve | (1) | Port (A) | Off (Open) | On* | ← | ← | |
| (2) | Port (B) | Off (Open) | On* | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | (5) | Port (E) | Off (Open) | ← | On (Closed) | ← |
| (6) | Port (F) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | (9) | Port (I) | Off (Closed) | ← | ← | On (Open) | |
| (10) | Port (J) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | *d | Right | - | Increases | Holds | Reduces | |
| *c | Left | - | Increases | Holds | Reduces | ||
| Rear Brake | Pressure Holding Solenoid Valve | (3) | Port (C) | Off (Open) | ← | On (Closed) | ← |
| (4) | Port (D) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | (7) | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| (8) | Port (H) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | *b | Right | - | Increases | Holds | Reduces | |
| *a | Left | - | Increases | Holds | Reduces | ||
*: The solenoid valve switches the hydraulic pressure between open and closed in accordance with the operating conditions by adjusting continually.
VSC
The VSC, by way of solenoid valves, controls the fluid pressure generated by the pump and applies it to the brake wheel cylinder of each wheel in the following 3 modes: pressure increase, pressure holding, and pressure reduction modes. As a result, the tendency to front wheel skid or rear wheel skid is controlled.
In the front wheel skid restraining control, the brake of the front wheel on the outer circle of the turn and the brakes of the rear wheels are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in the pressure increase mode, as it controls the front wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.
| Item | Not Activated | VSC Operation | |||||
|---|---|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||||
| Pump | Off | On | ← | ← | |||
| Master Cylinder Cut Solenoid Valve | (1) | Port (A) | Off (Open) | On* | ← | ← | |
| (2) | Port (B) | Off (Open) | On* | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | (5) | Port (E) | Off (Open) | ← | On (Closed) | ← |
| (6) | Port (F) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | (9) | Port (I) | Off (Closed) | ← | ← | On (Open) | |
| (10) | Port (J) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | *d | Right | - | - | - | - | |
| *c | Left | - | Increases | Holds | Reduces | ||
| Rear Brake | Pressure Holding Solenoid Valve | (3) | Port (C) | Off (Open) | ← | On (Closed) | ← |
| (4) | Port (D) | Off (Open) | ← | On (Closed) | ← | ||
| Pressure Reduction Solenoid Valve | (7) | Port (G) | Off (Closed) | ← | ← | On (Open) | |
| (8) | Port (H) | Off (Closed) | ← | ← | On (Open) | ||
| Wheel Cylinder Pressure | *b | Right | - | Increases | Holds | Reduces | |
| *a | Left | - | Increases | Holds | Reduces | ||
*: The solenoid valve switches the hydraulic pressure between open and closed in accordance with the operating conditions by adjusting continually.
During the rear wheel skid restraining control, the brakes of the front wheel on the outer circle of the turn are applied. Also, depending on whether the brake is on or off and also depending on the condition of the vehicle, there are circumstances in which the brake might not be applied to the wheels even if the wheel is targeted for braking. The following diagram shows the hydraulic circuit in the pressure increase mode, as it controls the rear wheel skid condition while the vehicle is making a right turn. In other operating modes, the pressure holding valve and the pressure reduction valve are turned on or off in accordance with the ABS and EBD operation patterns.
| Item | Not Activated | VSC Operation | |||||
|---|---|---|---|---|---|---|---|
| Pressure Increase Mode | Pressure Holding Mode | Pressure Reduction Mode | |||||
| Pump | Off | On | ← | ← | |||
| Master Cylinder Cut Solenoid Valve | (1) | Port (A) | Off (Open) | On* | ← | ← | |
| (2) | Port (B) | Off (Open) | On* | ← | ← | ||
| Front Brake | Pressure Holding Solenoid Valve | (5) | Port (E) | Off (Open) | ← | On (Closed) | ← |
| (6) | Port (F) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | (9) | Port (I) | Off (Closed) | ← | ← | On (Open) | |
| (10) | Port (J) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | *d | Right | - | - | - | - | |
| *c | Left | - | Increases | Holds | Reduces | ||
| Rear Brake | Pressure Holding Solenoid Valve | (3) | Port (C) | Off (Open) | On (Closed) | ← | ← |
| (4) | Port (D) | Off (Open) | On (Closed) | ← | ← | ||
| Pressure Reduction Solenoid Valve | (7) | Port (G) | Off (Closed) | ← | ← | ← | |
| (8) | Port (H) | Off (Closed) | ← | ← | ← | ||
| Wheel Cylinder Pressure | *b | Right | - | - | - | - | |
| *a | Left | - | - | - | - | ||
*: The solenoid valve switches the hydraulic pressure between open and closed in accordance with the operating conditions by adjusting continually.