| for Bosch made | Starter | No-load characteristics current | 123A or less at 11.5 V |
| Starter armature assembly | Maximum circle runout | 0.04 mm (0.0016 in.) | |
| Standard circle runout | 0.02 mm (0.0008 in.) | ||
| Standard commutator diameter | 32.2 mm (1.2783 in.) | ||
| Minimum commutator diameter | 31.1 mm (1.2347 in.) | ||
| Standard undercut depth | 0.9 mm (0.0354 in.) | ||
| Minimum undercut depth | 0.4 mm (0.0157 in.) | ||
| Segments | Below 1.7 Ω | ||
| Segment - Coil core | 10 kΩ or higher | ||
| Brush | Standard length | 14.0 mm (0.5558 in.) | |
| Minimum length | 9.0 mm (0.3543 in. ) | ||
| Tester connection
A-B |
10 kΩ or higher | ||
| Tester connection
A-C |
10 kΩ or higher | ||
| Tester connection
A-D |
Below 1 Ω | ||
| Tester connection
B-C |
Below 1 Ω | ||
| Tester connection
B-D |
10 kΩ or higher | ||
| Tester connection
C-D |
10 kΩ or higher | ||
| Magnet starter switch | Terminal 50 - Terminal C | Below 1 Ω | |
| Terminal 50 - Body | Below 2 Ω | ||
| for Denso made | Starter | No-load characteristics current | 100 A or less at 11.5 V |
| Starter armature | Maximum circle runout | 0.05 mm (0.00198 in.) | |
| Standard commutator diameter | 35.0 mm (1.38 in.) | ||
| Minimum commutator diameter | 34.0 mm (1.34 in.) | ||
| Standard undercut depth | 0.7 mm (0.0276 in.) | ||
| Minimum undercut depth | 0.2 mm (0.00787 in.) | ||
| Segments | Below 1 Ω | ||
| Segment - Coil core | 10 kΩ or higher | ||
| Brush length | Standard length | 15.0 mm (0.591 in.) | |
| Minimum length | 9.0 mm (0.354 in. ) | ||
| Brush spring | Standard spring installed load | 22 to 28 N
(2 to 3 kgf*cm, 4.8 to 6.2 in.*lbf) |
|
| Minimum spring installed load | 13 N
(1 kgf*cm, 2.9 in.*lbf) |
||
| Brush holder | Positive brush - Negative brush | 10 kΩ or higher | |
| Magnet starter switch | Terminal 50 - Terminal C | Below 1 Ω | |
| Terminal 50 - Body | Below 2 Ω | ||
| Starter relay | Specified resistance
3-5 |
10 kΩ or higher | |
| Below 1 Ω
(when battery voltage is applied to terminal 1 and 2) |
|||
| Glow relay | Specified resistance
3-5 |
10 kΩ or higher | |
| Below 1 Ω
(when battery voltage is applied to terminal 1 and 2) |
|||
| Ignition switch | Tester connection
- |
Switch condition
Lock |
Specified condition
10 kΩ or higher |
| Tester connection
2 (ACC) - 4 (AM1) |
Switch condition
ACC |
Specified condition
Below 1 Ω |
|
| Tester connection
1 (IG1) - 4 (AM1) 2 (ACC) - 4 (AM1) 5 (AM2) - 6 (IG2) |
Switch condition
ON |
Specified condition
Below 1 Ω |
|
| Tester connection
1 (IG1) - 4 (AM1) 3 (ST1) - 4 (AM1) 5 (AM2) - 6 (IG2) 5 (AM2) - 7 (ST2) |
Switch condition
START |
Specified condition
Below 1 Ω |
|