RM1840EF
_V1
General
_009566
SPECIFICATIONS
_0052038
1GR-FE ENGINE CONTROL
F
SPECIFICATIONS 1GR-FE ENGINE CONTROL SERVICE DATA
CAMSHAFT OIL CONTROL VALVE
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
20°C (68°F)
|
6.9 to 7.9 Ω
|
THROTTLE BODY
| Tester Connection
|
Condition
|
Specified Condition
|
| 2 (M+) - 1 (M-)
|
20°C (68°F)
|
0.3 to 100 Ω
|
ACCELERATOR PEDAL
| Tester display
|
Condition
|
Specified Condition
|
| Accel Sensor Out No. 1
|
Released
|
0.5 to 1.1 V
|
| Depressed
|
2.6 to 4.5 V
|
| Accel Sensor Out No. 2
|
Released
|
1.2 to 2.0 V
|
| Depressed
|
3.4 to 4.98 V
|
CRANKSHAFT POSITION SENSOR
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (NE) - 2 (NE-)
|
Cold
|
1630 to 2740 Ω
|
| Hot
|
2065 to 3225 Ω
|
ENGINE COOLANT TEMPERATURE SENSOR
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
Approx. 20°C (68°F)
|
2.32 to 2.59 kΩ
|
| Approx. 80°C (176°F)
|
0.310 to 0.326 kΩ
|
KNOCK SENSOR
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 - 2
|
20°C (68°F)
|
120 to 280 kΩ
|
AIR FUEL RATIO SENSOR (for Bank 1)
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HA1A) - 2 (+B)
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
| 1 (HA1A) - 4 (A1A-)
|
Always
|
10 kΩ or higher
|
AIR FUEL RATIO SENSOR (for Bank 2)
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HA2A) - 2 (+B)
|
20°C (68°F)
|
1.8 to 3.4 Ω
|
| 1 (HA2A) - 4 (A2A-)
|
Always
|
10 kΩ or higher
|
HEATED OXYGEN SENSOR (for Bank 1)
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HT1B) - 2 (+B)
|
20°C (68°F)
|
11 to 16 Ω
|
| 1 (HT1B) - 4 (E2)
|
Always
|
10 kΩ or higher
|
HEATED OXYGEN SENSOR (for Bank 2)
| Tester Connection
|
Condition
|
Specified Condition
|
| 1 (HT2B) - 2 (+B)
|
20°C (68°F)
|
11 to 16 Ω
|
| 1 (HT2B) - 4 (E2)
|
Always
|
10 kΩ or higher
|
NO. 1 INTEGRATION RELAY (C/OPN)
| Tester Connection
|
Condition
|
Specified Condition
|
| 1J-5 - 1J-8
|
Battery voltage not applied to terminals 1J- 6 and 1J-7
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1J-6 and 1J-7
|
Below 1 Ω
|
NO. 1 INTEGRATION RELAY (MAIN)
| Tester Connection
|
Condition
|
Specified Condition
|
| EFI fuse
|
Always
|
Below 1 Ω
|
| 1J-1 - 1J-4
|
Battery voltage not applied to terminals 1J- 2 and 1J-3
|
10 kΩ or higher
|
| Battery voltage applied to terminals 1J-2 and 1J-3
|
Below 1 Ω
|
AIR FUEL RATIO SENSOR HEATER RELAY (A/F)
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
FUEL PUMP RELAY (F/PMP)
| Tester Connection
|
Condition
|
Specified Condition
|
| 3 - 4
|
Battery voltage is not applied to terminals 1 and 2
|
Below 1 Ω
|
| Battery voltage is applied to terminals 1 and 2
|
10 kΩ or higher
|
| 3 - 5
|
Battery voltage is not applied to terminals 1 and 2
|
10 kΩ or higher
|
| Battery voltage is applied to terminals 1 and 2
|
Below 1 Ω
|
SPARK PLUG
| Recommended spark plug
|
Correct electrode gap for new spark plug
|
Maximum electrode gap for used spark plug
|
Standard insulation resistance
|
| K20HR-U11
|
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
|
1.3 mm (0.0512 in.)
|
10 MΩ or higher
|
| LFR6C11
|