The EGR system recirculates exhaust gases in a way that suits every driving condition. The recirculated gas mixes with intake air. Therefore, the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.
In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and the throttle valve angle.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0489 | Exhaust Gas Recirculation Control Circuit Low | Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic). | ·
Electric vacuum regulating valve assembly ·
Open or short in electric vacuum regulating valve assembly circuit ·
ECM |
Comes on | DTC stored |
| P0490 | Exhaust Gas Recirculation Control Circuit High | Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic). | ·
Electric vacuum regulating valve assembly ·
Open or short in electric vacuum regulating valve assembly circuit ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P0489 | ·
Actual EGR Valve Pos. ·
Target EGR Valve Pos. |
| P0490 |
| DTC Detection Drive Pattern | 5 seconds after engine is started |
Refer to DTC P0400 (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0400).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Inspect the electric vacuum regulating valve assembly.
Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>VACUUM REGULATING VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Electric Vacuum Regulating Valve Assembly) |
Disconnect the electric vacuum regulating valve assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C90-1 - Body ground | Ignition switch ON | 11 to 14 V |
Reconnect the electric vacuum regulating valve assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the electric vacuum regulating valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C90-2 - C23-9 (EGR) | Always | Below 1 Ω |
| C90-2 or C23-9 (EGR) - Body ground | Always | 10 kΩ or higher |
Reconnect the electric vacuum regulating valve assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric vacuum regulating valve assembly.
Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>VACUUM REGULATING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
If the voltage at the electric vacuum regulating valve assembly connector is not 11 to 14 V, repair or replace the harness and connector between the electric vacuum regulating valve assembly and the MAIN relay.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Start the engine.
Idle the engine for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT