Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler)
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) J

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  Turbocharger Noise  


DESCRIPTION

HINT:

Turbocharger noise is classified into 2 types. One is whistling noise, and the other is whining noise. When troubleshooting, the type of noise should be determined first.


Description
Noise Type Noise Description Main Trouble Area
Whistling noise The volume and pitch of this noise are proportional to turbocharger speed or engine speed. Therefore, the noise level will become more obvious when engine speed increases.
·

Turbocharger (e.g. shaft imbalance)

·

Gear inside engine

·

Transmission gear

·

Intake air system leakage

·

Intake air system breakage


Whining noise This noise has a lower pitch than whistling noise. It generally occurs in the engine speed range of 1500 to 2500 rpm, and has a relatively constant pitch, independent of engine speed and vehicle speed. Turbocharger
HINT:
·

Example: Vibration of turbocharger is transferred to exhaust pipe which causes resonation and noise.

·

Example: Vibration of turbocharger is transferred through exhaust pipe to vehicle body (floor) which then vibrates causing noise.




Faults and Symptoms of Diesel Engine Components


Turbocharger System
Main fault Turbocharger turbine shaft imbalance
Symptoms High-pitched whistling noise
HINT:

The pitch and volume change in proportion to the turbocharger speed.



Intake System
Main fault Leakage
Symptoms Leak flow noise

Gear inside Engine
Symptoms Gear noise
HINT:

The pitch and volume change in proportion to the engine speed.



Transmission Gear
Symptoms Gear noise
HINT:

The pitch and volume change in proportion to the transmission gear speed.




PROCEDURE

1.CONFIRM CONDITION IN WHICH NOISE OCCURRED
a.

Confirm with the customer the conditions in which the noise occurred.

HINT:

To clearly understand the conditions in which the noise occurred, the items in the table below are useful.


Item Note
Engine speed Engine speed range
Vehicle speed Vehicle speed range
Transmission gear Which gear?
Accelerator pedal position During acceleration or deceleration?
Temperature
·

Ambient temperature

·

Engine temperature (cold, warmed up, etc.)


Road conditions
·

City or highway driving

·

Uphill or downhill


Noise level
·

Did the noise occur suddenly, or build gradually?

·

Has the noise gradually been getting louder?


Other symptoms
·

Lack of power

·

High fuel consumption, etc.


Noise recognition What made the customer determine the noise to be abnormal?


Result:
Proceed to
NEXT



NEXT

2.CONFIRM NOISE CUSTOMER MENTIONED (PROCEDURE 2)
2.CONFIRM NOISE CUSTOMER MENTIONED (PROCEDURE 2)
a.

Check for the noise described by the customer.

HINT:

If a noise is heard, make sure that the noise matches the noise described by the customer.


Result:
Result Proceed to
Obvious abnormal noise matching noise described by customer is confirmed A
Obvious abnormal noise matching noise described by customer is not confirmed B




A

3.CHECK INTAKE SYSTEM

B

7.EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL
3.CHECK INTAKE SYSTEM
a.

Check for air leakage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Check for disconnected or improperly connected hoses, and gaps between hoses and parts.

·

Check for foreign matter between the air cleaner and turbocharger.




Result:
Proceed to
OK
NG



OK

4.CONFIRM NOISE SOURCE (FORM TURBOCHARGER OR NOT)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.CONFIRM NOISE SOURCE (FORM TURBOCHARGER OR NOT)
a.

Disconnect the actuator hose from the compressor housing.


b.

Stop up the compressor housing side tube with a hose clip or equivalent.


c.
A148172

Using SST, apply pressure to the actuator to open the waste gate valve.

Valve opening pressure:

Specified pressure* (See attached table below)


NOTICE:

Never apply more than predetermined maximum pressure* to the actuator.


HINT:

*: Valve opening pressure and predetermined maximum pressure above differ according to the turbocharger. For the specifications, see attached table below.


Specifications:
Engine Type Turbocharger Sub-assembly
(Part No.)
Valve Opening Pressure
(kPa: Gauge Pressure)
Maximum Pressure
(kPa: Gauge Pressure)
Reference:
Rod Stroke
(mm)
2KD-FTV 17201-0L030
17201-30120
114 136 0.98 to 1.91
17201-0L050 123 147.8 0.89 to 1.74


d.

Check that the actuator rod moves and that the waste gate valve opens.


e.

Start the engine and allow it to idle.


f.

Rev the engine up several times, depressing the accelerator pedal.

NOTICE:

Do not accelerate the engine while sufficient pressure is not applied to the actuator. The boost pressure (turbocharged air pressure) may exceed the prescribed booster pressure limit and the engine may be damaged due to overboost.



g.

Check whether the noise is reduced or not compared with the noise under the original conditions.


h.

Reconnect the actuator hose to the compressor housing.

Result:
Result Proceed to
The noise is reduced (or disappears) A
The noise is the same as in Procedure 2 (The noise does not change) B



HINT:
·

When the waste gate valve opens regardless of the engine condition, the turbocharger speed slows down and the cause of noise can be confirmed that is from the turbocharger or not.

·

If the turbocharger is the cause of the noise, the noise will be reduced when the waste gate valve opens because turbocharger speed does not increase.




A

5.CONFIRM THE NOISE TYPE

B

8.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 8)
5.CONFIRM THE NOISE TYPE
a.

Check whether the noise can be heard even when the engine speed is more than 3000 rpm, and whether the noise gradually gets louder as the engine speed increases.

HINT:

If so, the noise is likely to be whistling noise. If not, the noise is likely to be whining noise.


Result:
Result Proceed to
Yes (The noise is likely to be whistling noise) A
No (The noise is likely to be whining noise) B




A

REPLACE TURBOCHARGER SUB-ASSEMBLY

B

6.PERFORM ALIGNMENT OF EXHAUST PIPE AND CONFIRM THE NOISE
6.PERFORM ALIGNMENT OF EXHAUST PIPE AND CONFIRM THE NOISE
a.

Disconnect the exhaust pipe at the ball joint and from each exhaust pipe support, and then realign the exhaust pipe and reconnect it to each exhaust pipe support and at the ball joint.

Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/o DPF)>COMPONENTS


A232871
0.219,3.885 1.51,4.104 1.292,0.219 2.625,1.385 3.333,1.573 0.708,0.188 5.688,1.906 6.406,2.083 0.719,0.177 1.177,3.26 1.896,3.438 0.719,0.177 2.885,1.844 2.885,1.573 false 5.375,1.719 5.375,2.583 false 4.833,2.125 4.833,2.375 false 3.469,2.125 3.469,2.417 false 2.563,2.438 2.563,3.125 false 0.635,1.719 0.813,1.594 0.813,1.594 1.156,1.594 false 5.719,0.594 5.521,0.417 5.521,0.417 5.344,0.417 false 6.01,1.521 6.01,1.906 false 0.833,2.01 0.896,1.875 0.896,1.875 1.063,1.875 false 5.813,0.99 5.698,0.875 5.698,0.875 5.177,0.875 false 6.375,1.302 6.531,1.5 6.531,1.5 6.531,2.573 false 2.208,1.844 2.354,1.125 2.354,1.125 2.458,1.125 false 1.344,2.698 1.052,3.125 1.052,3.125 1.052,3.51 false 1.5,2.979 1.5,3.26 false 5.292,2.604 5.5,2.771 0.208,0.167 10 false *7 2.49,3.156 2.708,3.344 0.219,0.188 10 false *4 0.24,3.906 1.5,4.115 1.26,0.208 10 false N*m (kgf*cm, ft.*lbf) 1.552,3.906 2,4.094 0.448,0.188 10 false : *a 0.375,4.24 0.698,4.427 0.323,0.188 10 false *b 2.677,1.396 3.313,1.563 0.635,0.167 8 false 48 (489, 35) 1.24,1.802 1.5,2 0.26,0.198 10 false *2 6.458,2.615 6.656,2.813 0.198,0.198 10 false *5 2.5,1.042 2.708,1.24 0.208,0.198 10 false *5 5,0.781 5.229,0.979 0.229,0.198 10 false *6 5.74,1.927 6.521,2.167 0.781,0.24 8 false 48 (489, 35) 1.24,3.281 1.927,3.458 0.688,0.177 8 false 43 (438, 32) 3.563,2.417 3.813,2.615 0.25,0.198 10 false *6 1.198,1.51 1.406,1.698 0.208,0.188 10 false *1 0.969,3.542 1.208,3.708 0.24,0.167 10 false *3 5.167,0.333 5.396,0.51 0.229,0.177 10 false *5 1.458,2.615 1.688,2.792 0.229,0.177 10 false x 2 1.583,2.844 1.813,3.021 0.229,0.177 10 false x 2 6.083,1.385 6.313,1.563 0.229,0.177 10 false x 2 2.969,1.792 3.198,1.979 0.229,0.188 10 true x 2 4.146,1.26 4.375,1.438 0.229,0.177 10 false x 2 4.76,2.417 4.99,2.594 0.229,0.177 10 false *5 0.26,4.229 0.417,4.427 0.156,0.198 10 false ● 3.438,2.385 3.594,2.583 0.156,0.198 10 false ● 1.135,1.792 1.292,1.99 0.156,0.198 10 false ● 4.875,0.771 5.031,0.969 0.156,0.198 10 false ●
*1 Outlet Pipe *2 Gasket (Ball Joint)
*3 Compression Spring *4 Front Exhaust Pipe Assembly
*5 Exhaust Pipe Support *6 Gasket
*7 Center Exhaust Pipe Assembly - -
*a Specified torque *b Non-reusable part


HINT:

Above illustration is an example.


b.

Confirm whether the noise problem is solved or not.

HINT:

The alignment of the exhaust pipe affects whining noise.


Result:
Result Proceed to
The noise problem is solved A
The noise problem remains B




A

END

B

REPLACE TURBOCHARGER SUB-ASSEMBLY

7.EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL
a.

Explain to the customer that the noise the customer mentioned is not abnormal.

HINT:

To help the customer understand, test driving another car with the customer may be helpful.



Result:
Proceed to
NEXT



NEXT

END

8.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 8)
a.

Check for the noise source with a sound scope.

NOTICE:

When performing this check, make sure that the sound scope, your body, etc., do not get caught on the V-belt.


HINT:
·

The source of the noise is not the turbocharger, but a part other than the turbocharger (e.g. a part inside the engine, transmission, or vacuum pump).

·

Sometimes gear noise may be mistaken for turbocharger noise. For gear noise, pay attention to the gear inside the engine and transmission gear.

·

Rev the engine up and check if the noise reduces at the same time the engine speed decreases. If the noise reduces at the same time the engine speed decreases, it is gear noise. If the noise reduces a short time after the engine speed decreases, it is turbocharger noise.

·

The following illustration is a reference for checking whether the noise source is from the engine.



A230523
4.49,3.073 4.594,3.073 4.594,3.073 4.771,2.542 true 6.344,0.573 6.01,0.573 6.01,0.573 5.771,0.917 true 6.427,3.042 6.323,3.042 6.323,3.042 5.781,2.521 true 4.042,0.917 4.135,0.917 4.135,0.917 4.625,1.26 true 5.99,0.99 6.229,0.594 true 3.49,0.365 3.708,0.552 0.219,0.188 10 false *a 3.865,0.833 4.083,1.021 0.219,0.188 10 false *1 6.385,0.49 6.604,0.677 0.219,0.188 10 false *2 4.323,3 4.542,3.188 0.219,0.188 10 false *4 6.458,2.958 6.677,3.146 0.219,0.188 10 false *3
*1 Timing Belt *2 Camshafts
*3 Crankshaft *4 Timing Gear Train
*a Gear Location inside Engine - -


HINT:
·

Above illustration is an example.

·

Gear noise can be confirmed with a sound scope. Put the sound scope on the cylinder block near the gear, and if the noise heard through the sound scope has the same timing as the noise heard without the sound scope, it is gear noise.




Result:
Proceed to
NEXT



NEXT

9.REPLACE THE PARTS DETECTED IN PROCEDURE 8
9.REPLACE THE PARTS DETECTED IN PROCEDURE 8
a.

Replace the parts detected in Procedure 8 as the noise source.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the noise problem has been successfully solved.


Result:
Proceed to
NEXT



NEXT

END