Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler)
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052067 ECD SYSTEM(w/ EGR Cooler) U

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  TERMINALS OF ECM  


A254878
1.21,0.403 1.611,0.639 0.402,0.235 1.282,0.448 1.596,0.629 0.314,0.181 10 C22 2.727,0.403 3.129,0.639 0.402,0.235 2.8,0.448 3.113,0.629 0.314,0.181 10 C23 4.29,0.403 4.691,0.639 0.402,0.235 4.362,0.448 4.676,0.629 0.314,0.181 10 G38 5.761,0.403 6.162,0.639 0.402,0.235 5.833,0.448 6.147,0.629 0.314,0.181 10 G39

HINT:

Each ECM terminal's standard voltage is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G38-2 (BATT) - C23-7 (E1) L - BR Battery (for measuring the battery voltage and for the ECM memory) Always 11 to 14 V
G39-9 (IGSW) - C23-7 (E1) B-O - BR Ignition switch Ignition switch ON 11 to 14 V
G39-1 (+B) - C23-7 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
G39-8 (MREL) - C23-7 (E1) W-G - BR MAIN relay Ignition switch ON 11 to 14 V
10 seconds elapsed after ignition switch off 0 to 1.5 V
C22-18 (VC) - C22-28 (E2) R-W - BR Power source of sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
C23-2 (VCS) - C23-1 (E2S) L-W - P-L Power source of fuel pressure sensor (sub) Ignition switch ON 4.5 to 5.5 V
G39-22 (VPA) - G39-28 (EPA) W-L - BR-W Accelerator pedal position sensor (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.0 V
Ignition switch ON, accelerator pedal fully depressed 2.9 to 4.2 V
G39-23 (VPA2) - G39-29 (EPA2) GR-G - BR-Y Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.4 to 1.8 V
Ignition switch ON, accelerator pedal fully depressed 3.7 to 5.0 V
G39-26 (VCPA) - G39-28 (EPA) LG-R - BR-W Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.0 V
G39-27 (VCP2) - G39-29 (EPA2) BR-R - BR-Y Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.0 V
C23-24 (VG) - C23-32 (EVG) W-R - B-W MAF meter Idling, A/C switch OFF 0.5 to 3.4 V
C22-31 (THA) - C22-28 (E2) Y-B - BR IAT sensor (built into MAF meter) Idling, intake air temperature at 20°C (68°F) 0.5 to 3.4 V
C22-20 (THIA) - C22-28 (E2) Y-G - BR Intake air temperature sensor Atmospheric air temperature 0.5 to 3.4 V
C22-19 (THW) - C22-28 (E2) R-L - BR ECT sensor Idling, engine coolant temperature at 80°C (176°F) 0.2 to 1.0 V
G39-7 (STA) - C23-7 (E1) L-Y - BR Starter signal Cranking 6.0 V or more
C22-24 (#1) - C23-7 (E1)
C22-23 (#2) - C23-7 (E1)
C22-22 (#3) - C23-7 (E1)
C22-21 (#4) - C23-7 (E1)
B-W - BR
R - BR
V - BR
Y-R - BR
Injector Idling Pulse generation
(see waveform 1)
C22-27 (NE+) - C22-34 (NE-) Y - L Crankshaft position sensor Idling Pulse generation
(see waveform 2)
C23-23 (G+) - C23-31 (G-) Y - L Camshaft position sensor Idling Pulse generation
(see waveform 2)
G38-15 (STP) - C23-7 (E1) G-W - BR Stop light switch Ignition switch ON, brake pedal depressed 7.5 to 14 V
Ignition switch ON, brake pedal released 0 to 1.5 V
G38-14 (ST1-) - C23-7 (E1) R-L - BR Stop light switch
(opposite to STP)
Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
G39-11 (TC) - C23-7 (E1) P-B - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
G39-12 (W) - C23-7 (E1) R-B - BR MIL MIL illuminated 0 to 3 V
MIL not illuminated 11 to 14 V
G38-17 (SPD) - C23-7 (E1) V-R - BR Speed signal from combination meter Ignition switch ON, slowly rotate wheel Pulse generation
(see waveform 3)
C23-28 (PIM) - C22-28 (E2) L-B - BR Manifold absolute pressure sensor Apply negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) 0.1 to 0.7 V
Same as atmospheric pressure 0.8 to 1.5 V
Apply positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) 1.6 to 2.3 V
G39-10 (IREL) - C23-7 (E1) B-W - BR EDU relay Ignition switch ON 0 to 1.5 V
G39-4 (TACH) - C23-7 (E1) B-W - BR Engine speed Idling Pulse generation
(see waveform 4)
C22-26 (PCR1) - C22-28 (E2) R-Y - BR fuel pressure sensor (main) Idling 1.7 to 2.2 V
C22-33 (PCR2) - C23-1 (E2S) G-R - P-L fuel pressure sensor (sub) Idling 1.2 to 1.6 V
G39-15 (GREL) - C23-7 (E1) R - BR GLOW relay Cranking 11 to 14 V
C22-29 (THF) - C22-28 (E2) G-B - BR Fuel temperature sensor Ignition switch ON 0.5 to 3.4 V
C22-8 (ALT) - C23-7 (E1) G - BR Generator duty ratio Idling Pulse generation
(see waveform 5)
C22-2 (PCV+) - C22-1 (PCV-) G-W - G-Y Suction control valve Idling Pulse generation
(see waveform 6)
C22-25 (INJF) - C23-7 (E1) P - BR EDU Idling Pulse generation
(see waveform 7)
C22-32 (PRD) - C23-7 (E1) GR - BR EDU Ignition switch off 4 to 6.5 V
C23-29 (VLU) - C22-28 (E2) B - BR Throttle position sensor Ignition switch ON, throttle valve
fully opened
3.6 to 4.2 V
Ignition switch ON, throttle valve
fully closed
0.4 to 1.0 V
C23-4 (LUSL) - C23-7 (E1) GR - BR Diesel throttle motor duty signal Engine warmed up, racing engine Pulse generation
(see waveform 8)
C22-15 (SCV) - C22-7 (E01) LG - W-B VSV for swirl control valve Idling 0 to 1.5 V
Engine speed 2600 rpm or more 11 to 14 V
C23-9 (EGR) - C23-7 (E1) L-R - BR E-VRV (for E-EGR) Ignition switch ON Pulse generation
(see waveform 9)
C23-18 (EGRC) - C23-7 (E1) Y-B - BR VSV (for EGR Cut) Ignition switch ON, EGR cuts
(accelerator pedal fully depressed)
0 to 1.5 V
C23-19 (ECBV) - C23-7 (E1) B-L - BR VSV (for No. 2 EGR valve) ON (open)
Idling (engine coolant temperature 75°C or more)
0 to 1.5 V
OFF (closed)
Idling (engine coolant temperature 75°C or less)
7.5 to 14 V
C23-33 (EGLS) - C23-7 (E1) L-Y - BR EGR valve position sensor Ignition switch ON 0.6 to 1.4 V
Idling 1.9 to 2.9 V

WAVEFORM 1


A208447
2.734,0.144 3.309,0.308 0.575,0.163 10 5 V/DIV. 0.173,0.406 0.574,0.569 0.401,0.163 10 (a) #1 0.173,0.79 0.574,0.953 0.401,0.163 10 (b) #3 0.173,1.177 0.574,1.34 0.401,0.163 10 (c) #4 0.173,1.572 0.574,1.735 0.401,0.163 10 (d) #2 1.496,1.844 2.461,2.007 0.964,0.163 10 20 msec./DIV.

Injector No. 1 (to No. 4) Injection Signal
ECM Terminal Name (a) Between #1 and E1
(b) Between #3 and E1
(c) Between #4 and E1
(d) Between #2 and E1
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 2


A098437
0.167,0.594 0.635,0.833 0.469,0.24 10 false (a) NE 0.24,1.469 0.677,1.677 0.438,0.208 10 false (b) G 2.771,0.292 3.417,0.49 0.646,0.198 10 false 5 V/DIV. 1.156,1.99 2.156,2.177 1,0.188 10 false 20 msec./DIV.

Crankshaft Position Sensor Signal and Camshaft Position Sensor Signal
ECM Terminal Name (a) Between NE+ and NE-
(b) Between G+ and G-
Tester Range 5 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the engine speed.



WAVEFORM 3


G037487
0.073,1.177 0.469,1.375 0.396,0.198 10 false SPD 2.75,0.406 3.406,0.604 0.656,0.198 10 false 5 V/DIV. 2.885,1.219 3.292,1.417 0.406,0.198 10 false GND 1.313,1.979 2.469,2.177 1.156,0.198 10 false 10 msec./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 5 V/DIV., 10 msec./DIV.
Condition Driving at vehicle speed of 40 km/h (25 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 4


A301908
0.438,0.281 1.094,0.51 0.656,0.229 10 false 5 V/DIV. 0.49,1.188 1.146,1.417 0.656,0.229 10 false GND 1.729,1.896 2.719,2.135 0.99,0.24 10 false 10 msec./DIV.

Engine Speed Signal
ECM Terminal Names Between TACH and E1
Tester Ranges 5 V/DIV., 10 msec./DIV.
Conditions Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 5


A155060
2.688,0.667 3.292,1 0.604,0.333 10 false 5 V/DIV. 1.292,2.719 2.208,2.969 0.917,0.25 10 false 2 msec./DIV. 0.448,1.625 0.781,1.865 0.333,0.24 10 false ALT 2.823,1.823 3.219,2.094 0.396,0.271 10 false GND

Generator Duty Ratio Signal
ECM Terminal Names Between ALT and E1
Tester Ranges 5 V/DIV., 2 msec./DIV.
Conditions Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 6


A097624
0.271,1.219 0.74,1.417 0.469,0.198 10 false PCV+ 2.802,0.969 3.25,1.323 0.448,0.354 10 false 10 V/DIV. 1.729,1.948 2.656,2.156 0.927,0.208 10 false 5 msec./DIV.

Suction Control Valve Signal
ECM Terminal Name Between PCV+ and PCV-
Tester Range 10 V/DIV., 5 msec./DIV.
Condition Idling or cranking with warm engine

HINT:

The waveform varies depending on the suction control valve operation.



WAVEFORM 7


A009437
0.406,0.865 0.813,1.063 0.406,0.198 10 false INJF 2.74,0.938 3.375,1.146 0.635,0.208 10 false 2 V/DIV. 1.448,1.938 2.396,2.156 0.948,0.219 10 false 20 msec./DIV.

Injector Injection Confirmation Signal
ECM Terminal Name Between INJF and E1
Tester Range 2 V/DIV., 20 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the injector injection.



WAVEFORM 8


A091225
0.365,1.073 0.844,1.271 0.479,0.198 10 false LUSL 2.688,1.083 3.292,1.281 0.604,0.198 10 false 1 V/DIV. 1.563,1.969 2.479,2.177 0.917,0.208 10 false 2 msec./DIV.

Diesel Throttle Motor Signal
ECM Terminal Name Between LUSL and E1
Tester Range 1 V/DIV., 2 msec./DIV.
Condition Warm engine with racing engine

HINT:

The waveform varies depending on the throttle valve operation.



WAVEFORM 9


A096634
0.229,1.031 0.646,1.229 0.417,0.198 10 false EGR 2.698,0.292 3.281,0.49 0.583,0.198 10 false 5 V/DIV. 2.865,1.229 3.292,1.427 0.427,0.198 10 false GND 1.531,1.948 2.417,2.146 0.885,0.198 10 false 1 msec./DIV.

E-VRV (for E-EGR) Signal
ECM Terminal Name Between EGR and E1
Tester Range 5 V/DIV., 1 msec./DIV.
Condition Idling with warm engine

HINT:

The waveform varies depending on the E-VRV (for E-EGR) operation.