Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052067 ECD SYSTEM(w/ EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P0069  MAP Sensor Too High or Too Low  


DESCRIPTION

To detect atmospheric pressure, the atmospheric pressure sensor built into the ECM is used in the common rail system. Following the changes in the atmospheric pressure, the ECM corrects the fuel injection volume, timing and duration, and adjusts the common rail internal fuel pressure to optimize combustion.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0069 MAP Sensor Too High or Too Low After the ignition switch is turned to ON, the difference between the atmospheric pressure sensor output and manifold absolute pressure sensor output is more than 8 kPa for 0.5 seconds (2 trip detection logic). ECM Comes on DTC stored

Related Data List
DTC No. Data List
P0069
·

Atmosphere Pressure

·

MAP



HINT:
·

Turn the ignition switch to ON and check the Atmosphere Pressure and MAP items in the Data List. If the atmospheric pressure displayed on the tester differs greatly from the actual atmospheric pressure (standard: 101 kPa), the sensor (atmospheric pressure sensor or manifold absolute pressure sensor) is malfunctioning.

·

If DTC P0069 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

P0069
DTC Detection Drive Pattern 1 second elapses after ignition switch turned from off to ON (starter remains off)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>INITIALIZATION).


HINT:
·

Although the DTC titles say manifold absolute pressure Sensor Too High or Too Low, these DTCs relate to the atmospheric pressure sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0069)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0069 and other DTCs are output A
P0069 is output B


HINT:

If codes other than P0069 are output, perform troubleshooting for those DTCs first.




A

B

2.REPLACE ECM
2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTC.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END