Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2237  Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1)  P2238  Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1)  P2239  Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1)  P2252  Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1)  P2253  Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P2237, P2238 and/or P2239 is present, refer to the DTC table for DPF system (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

These DTCs are recorded when the air fuel ratio sensor has a malfunction, although the title is the oxygen sensor.



The air fuel ratio sensor has the characteristic of providing output voltage which is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage* is used by the ECM to control the air-fuel ratio.

The air fuel ratio sensor is located after the DPF catalytic converter. This sensor has been developed based on the structure and technology of a sensor that is being used for gasoline engines. The cover portion of the sensor has been changed for use in the diesel engine with DPF in order to eliminate the influence of the sensor temperature and particulate matter (PM).

In order to reduce both PM, the ECM adjusts the air-fuel ratio to slightly rich (but it is lean compared with the stoichiometric air-fuel ratio) based on signals from the air fuel ratio sensor. When the ECM performs PM forced regeneration using adding fuel using the exhaust fuel addition injector, the air-fuel ratio is also properly adjusted using the sensor.

*: The voltage value changes inside the ECM only.

A258975
5.24,2.021 5.771,2.531 true 5.021,1.802 5.688,1.99 true 5.167,1.396 5.677,1.344 true 5.396,1.292 5.719,1.115 true 5.177,1.729 5.688,1.979 true 3.208,2.281 3.854,1.938 false 3.031,2.219 2.302,1.854 true 2.583,2.625 2.708,2.823 0.125,0.198 10 false A 3.271,2.625 3.396,2.802 0.125,0.177 10 false A 1.76,1.75 2.427,1.979 0.667,0.229 10 false Element 0.677,2.083 1.552,2.302 0.875,0.219 10 false Exhaust Gas 4.875,2.677 5.802,2.938 0.927,0.26 10 false A-A Section 5.719,1.917 7.146,2.198 1.427,0.281 10 false Platinum Electrode 3.906,1.875 4.417,2.135 0.51,0.26 10 false Cover 5.823,2.479 6.115,2.677 0.292,0.198 10 false Air 5.76,0.969 6.219,1.146 0.458,0.177 10 false Heater 5.729,1.219 6.854,1.646 1.125,0.427 10 false Solid Electrolyte (Zirconia Element) 0.406,4.792 1.552,5 1.146,0.208 10 false AF Lambda B1S1 0.375,6.115 1.604,6.313 1.229,0.198 10 false AFS Voltage B1S1 2.031,4.875 2.198,5.083 0.167,0.208 10 false 1 2.031,4.354 2.198,4.563 0.167,0.208 10 false 2 2.042,6.24 2.208,6.448 0.167,0.208 10 false 1 2.042,6.781 2.208,6.99 0.167,0.208 10 false 0 2.031,5.406 2.198,5.615 0.167,0.208 10 false 0 2.042,5.719 2.208,5.927 0.167,0.208 10 false 2 2.302,5.698 2.531,5.948 0.229,0.25 10 false (V) 2.927,6.979 3.177,7.229 0.25,0.25 10 false 10 3.24,7.073 3.594,7.323 0.354,0.25 10 false 14.5 3.688,6.979 3.938,7.229 0.25,0.25 10 false 20 4.458,6.979 4.708,7.229 0.25,0.25 10 false 30 5.229,6.979 5.479,7.229 0.25,0.25 10 false 40 5.99,6.979 6.24,7.229 0.25,0.25 10 false 50 0.156,3.354 2.458,3.635 2.302,0.281 10 false Air-Fuel Ratio Displayed on Tester: 3.688,7.292 4.625,7.49 0.938,0.198 10 false Air-Fuel Ratio 4.104,4.99 6.729,5.323 2.625,0.333 10 false AF Lambda B1S1 = Air-Fuel Ratio / 14.5 2.604,8.281 3.021,8.469 0.417,0.188 10 false 0.060 4.833,8.281 5.25,8.469 0.417,0.188 10 false 0.508 5.406,8.281 5.823,8.469 0.417,0.188 10 false 0.787 5.958,8.281 6.375,8.469 0.417,0.188 10 false 0.978 6.51,8.281 6.927,8.469 0.417,0.188 10 false 1.373 4.281,8.281 4.698,8.469 0.417,0.188 10 false 0.336 3.729,8.281 4.146,8.469 0.417,0.188 10 false 0.268 3.167,8.281 3.583,8.469 0.417,0.188 10 false 0.170 2.188,8.281 2.375,8.469 0.188,0.188 10 false 0 2.115,8.729 2.448,8.917 0.333,0.188 10 false 14.5 6.031,8.729 6.365,8.917 0.333,0.188 10 false 30 2.688,8.729 3.021,8.917 0.333,0.188 10 false 15 4.906,8.729 5.24,8.917 0.333,0.188 10 false 20 6.615,8.729 6.948,8.917 0.333,0.188 10 false 50 3.802,8.729 4.135,8.917 0.333,0.188 10 false 17 3.229,8.729 3.563,8.917 0.333,0.188 10 false 16 0.375,8.729 1.313,8.927 0.938,0.198 10 false Air-Fuel Ratio 4.344,8.729 4.677,8.917 0.333,0.188 10 false 18 5.479,8.729 5.813,8.917 0.333,0.188 10 false 25 1.146,8.219 1.375,8.469 0.229,0.25 10 false (V) 0.323,8.146 1.115,8.521 0.792,0.375 10 false AFS Voltage B1S1 0.333,7.615 1.135,8 0.802,0.385 10 false AF Lambda B1S1 2.146,7.771 2.375,7.938 0.229,0.167 10 false 1.0 2.625,7.771 2.969,7.948 0.344,0.177 10 false 1.03 3.177,7.771 3.49,7.969 0.313,0.198 10 false 1.10 3.719,7.771 4.031,7.917 0.313,0.146 10 false 1.17 4.302,7.771 4.594,7.969 0.292,0.198 10 false 1.24 4.833,7.771 5.146,7.917 0.313,0.146 10 false 1.38 5.417,7.771 5.75,7.927 0.333,0.156 10 false 1.72 5.969,7.771 6.26,7.917 0.292,0.146 10 false 2.07 6.563,7.771 6.885,7.927 0.323,0.156 10 false 3.45 0.396,9.156 0.792,9.344 0.396,0.188 10 false HINT: 0.667,9.427 6.219,9.698 5.552,0.271 10 false *1: AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V or less. 1.5,8.292 1.948,8.479 0.448,0.188 10 false -0.549 1.583,8.729 1.917,8.917 0.333,0.188 10 false 12 1.542,7.781 1.854,7.948 0.313,0.167 10 false 0.83 1.438,8.063 1.635,8.25 0.198,0.188 10 false *1 2.042,3.875 2.208,4.083 0.167,0.208 10 false 3

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the B+ side of the circuit.


A210271
3.531,0.823 3.656,0.979 3.656,0.979 3.854,0.979 false 3.583,1.281 3.667,1.375 3.667,1.375 3.865,1.375 false 0.042,0.031 0.823,0.292 0.781,0.26 10 false Reference: 0.083,0.635 0.573,1 0.49,0.365 10 false from Battery 1.563,0.292 2.427,0.625 0.865,0.333 10 false A/F Relay 2.813,0.281 4.344,0.531 1.531,0.25 10 false Air Fuel Ratio Sensor 0.75,0.865 1.521,1.198 0.771,0.333 10 false A/F Fuse 3.906,0.896 4.375,1.094 0.469,0.198 10 false Heater 3.906,1.292 4.385,1.49 0.479,0.198 10 false Sensor 5.594,0.24 5.99,0.438 0.396,0.198 10 false ECM 4.896,0.646 5.292,0.844 0.396,0.198 10 false HAF2 4.896,1.063 5.271,1.26 0.375,0.198 10 false AF2+ 4.896,1.49 5.24,1.688 0.344,0.198 10 false AF2- 6.083,1.219 6.594,1.583 0.51,0.365 10 false Duty Control 0.885,1.688 2.167,1.917 1.281,0.229 10 false from MAIN Relay

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) When either of the following conditions is met (1 trip detection logic):
·

Air fuel ratio sensor circuit malfunction

·

The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.


Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor circuit low (bank 1 sensor 1)
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor circuit high (bank 1 sensor 1)
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor circuit low (bank 1 sensor 1)
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor circuit high (bank 1 sensor 1)
(1 trip detection logic)
Main trouble area: Short in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2237
·

AFS Voltage B1S1

·

Exhaust Temperature B1S1


P2238
P2239
P2252
P2253

CONFIRMATION DRIVING PATTERN

P2237
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the intelligent tester.


When either of the following conditions is met (1 trip detection logic):
·

Air fuel ratio sensor circuit malfunction

·

The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more.


Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



P2238, P2239, P2252, P2253
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 7 seconds Air fuel ratio sensor circuit low (bank 1 sensor 1)
(1 trip detection logic)
Main trouble area: Open in air fuel ratio sensor circuit
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM



MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air-fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C124-3 (AF2+) - C111-2 (AF2+) Always Below 1 Ω
C124-4 (AF2-) - C111-1 (AF2-) Always Below 1 Ω
C124-3 (AF2+) or C111-2 (AF2+) - Body ground Always 10 kΩ or higher
C124-4 (AF2-) or C111-1 (AF2-) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.



g.

Confirm that the DTC is not output again.


Result:
Proceed to
OK
NG



OK

END

NG

4.REPLACE ECM
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.



g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END