Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2610  ECM / PCM Internal Engine Off Timer Performance  


DESCRIPTION

The soak timer operates after the ignition switch is turned off. When a certain amount of time has elapsed after turning the ignition switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.

A258905
2.76,0.438 3.052,0.635 0.292,0.198 10 false IG2 0.698,4.781 1.271,5.063 0.573,0.281 10 false Battery 3.583,0.667 3.906,0.865 0.323,0.198 10 false IGN 4.885,0.396 5.385,0.625 0.5,0.229 10 false IGSW 1.927,0.438 2.271,0.625 0.344,0.188 10 false AM2 0.583,1.552 0.948,1.792 0.365,0.24 10 false AM2 4.563,2.99 4.823,3.219 0.26,0.229 10 false +B 4.365,5.469 4.802,5.677 0.438,0.208 10 false MREL 5.479,6.323 5.854,6.521 0.375,0.198 10 false ECM 5.052,0.792 6.031,1.073 0.979,0.281 10 false Soak Timer IC 5.146,2.969 6.313,3.198 1.167,0.229 10 false Power Source IC 3.073,4.521 3.49,4.719 0.417,0.198 10 false MAIN 1.594,3.792 1.896,4.01 0.302,0.219 10 false EFI 0.552,3.823 1.25,4.083 0.698,0.26 10 false BATT P/I 1.979,6.125 3.583,6.438 1.604,0.313 10 false No. 1 Integration Relay 1.927,0.979 2.979,1.229 1.052,0.25 10 false Ignition Switch 5.01,5.156 6.448,5.396 1.438,0.24 10 false Main Relay Control IC 4.49,3.813 4.813,4.021 0.323,0.208 10 false +B2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction (2 trip detection logic). ECM Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P2610
DTC Detection Drive Pattern -

MONITOR DESCRIPTION

1.

While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM interprets this as a malfunction, illuminates the MIL and stores the DTC.

2.

If the soak timer activates the ECM even though only a short amount of time has elapsed since the ignition switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the ignition switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the ignition switch is turned to ON.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:
·

DTC P2610 is stored if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is necessary.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CHECK WHETHER DTC OUTPUT RECURS
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Start the engine and wait for 10 minutes or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Powertrain > Engine > Trouble Codes
50001 61

g.

If no pending DTC is output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END