| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P062F | Internal Control Module EEPROM Error | When any condition below is met (1 trip detection logic):
·
Fuel injector compensation code is not registered. ·
Wrong injector compensation code is registered. ·
Fuel injector pilot quantity learning value is not registered. ·
Catalyst deterioration learning value is not registered. ·
Crank Time Compensation Learning value is not registered.* ·
A/F Sensor Compensation Learning value is not registered.* |
·
Fuel injector compensation code ·
Fuel injector pilot quantity learning value ·
Catalyst thermal deterioration value ·
A/F sensor compensation learning value ·
Crank time compensation learning value ·
ECM |
Comes on | DTC stored |
*: When this malfunction occurs, the MIL does not illuminate.
When a fuel injector is replaced, the new fuel injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing fuel injector compensation codes must be input into the new ECM.
Fuel injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each fuel injector. If an incorrect fuel injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.
When a fuel injector is replaced, perform pilot quantity learning. When the ECM is replaced, all of the existing fuel injector pilot quantity learning values must be input into the new ECM.
When the catalyst converter is replaced, the new catalyst thermal deterioration value must be input into the ECM. When the ECM is replaced, the existing catalyst thermal deterioration value must be input into the new ECM.
When replacing the ECM with a new one, if the injector compensation code, injector pilot quantity learning value and/or catalyst thermal deterioration value are not entered, DTC P062F will be stored.
When replacing the ECM with a new one, input all learning values and codes into the new ECM as follows:
Prior to replacing the ECM, use the intelligent tester to read and save each learning value and code from the original ECM (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
After installing a new ECM, input the saved learning values and codes into the new ECM using the tester (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Turn the ignition switch off and turn the tester off.
Wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Clear DTC P062F stored in the ECM using the tester (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR).
Each fuel injector has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector.
When you first turn ON the ignition switch after replacing the ECM and other component(s), DTC P062F is stored. Manually clear the DTC upon completion of compensation code registration.
| Replacement Part | Utility Item |
|---|---|
| ECM |
|
| DPF catalyst |
|
| Injector |
|
| DTC Detection Drive Pattern | Ignition switch ON for 1 second |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Tester Display |
|---|
| Learning Values Confirmation |
| Result | Proceed to |
|---|---|
| The injector compensation codes are not input | A |
| The injector compensation codes registered in the ECM are different than the codes imprinted on the injectors | |
| The pilot quantity learning values are set to the default values | B |
| The catalyst deterioration learning values are set to the default values | |
| Except above | C |
When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.
When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.
A
B
C
Register the injector compensation code.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Tester Display |
|---|
| Injector Compensation |
| Proceed to |
|---|
| NEXT |
NEXT
When replacing the ECM, after performing "Learning Values Save" to save the learned values from the old ECM using the intelligent tester and replacing the old ECM with a new one, "Learning Values Write" was not performed using the intelligent tester causing this DTC to be output.
Install the old ECM.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Tester Display |
|---|
| Learning Values Save |
Remove the old ECM.
Install a new ECM.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Tester Display |
|---|
| Learning Values Write |
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Tester Display |
|---|
| Learning Values Confirmation |
| Result | Proceed to |
|---|---|
| The pilot quantity learning values are set to the default values | A |
| The catalyst deterioration learning values are set to the default values | B |
| Except above | C |
When the catalyst deterioration learning values are set to the default values, "FFFFFFFF" is displayed.
When the fuel injector pilot quantity learning values are set to the default values, "7FFF" is displayed.
A
B
C
Perform the fuel injector pilot quantity learning.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION
| Tester Display |
|---|
| Pilot Quantity Learning |
| Proceed to |
|---|
| NEXT |
NEXT
Replace the front exhaust pipe assembly.
Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EXHAUST FUEL ADDITION INJECTOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Perform the catalyst record clear.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION
| Tester Display |
|---|
| Catalyst Record Clear |
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off and leave the vehicle for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| P062F is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off and leave the vehicle for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT