The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P007C | Charge Air Cooler Temperature Sensor Circuit Low | Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic). | ·
Short in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (turbo) ·
ECM |
Comes on | DTC stored |
| P007D | Charge Air Cooler Temperature Sensor Circuit High | Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic). | ·
Open in intake air temperature sensor (turbo) circuit ·
Intake air temperature sensor (turbo) ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P007C | Intake Air Temp (Turbo) |
| P007D |
If DTC P007C or P007D is stored, the following symptoms may appear:
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
| DTC Detection Drive Pattern | Ignition switch ON for 1 second |
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
Same as air temperature near intake manifold
| Result | Proceed to |
|---|---|
| -40°C (-40°F) | A |
| 140°C (284°F) or higher | B |
| OK (same as air temperature near intake manifold) | C |
If there is an open circuit, the tester indicates -40°C (-40°F).
If there is a short circuit, the tester indicates 140°C (284°F) or higher.
A
B
C
| *1 | Intake Air Temperature Sensor (Turbo) |
| *2 | ECM |
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor(Turbo)) |
Disconnect the intake air temperature sensor (turbo) connector.
Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
140°C (284°F) or higher
Reconnect the intake air temperature sensor (turbo) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C18-2 - C113-3 (THIA) | Always | Below 1 Ω |
| C18-1 - C114-14 (E2) | Always | Below 1 Ω |
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
| *1 | Intake Air Temperature Sensor
(Turbo) |
| *2 | ECM |
Disconnect the intake air temperature sensor (turbo) connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).
| Tester Display |
|---|
| Intake Air Temp (Turbo) |
Read the value.
-40°C (-40°F)
Reconnect the intake air temperature sensor (turbo) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the intake air temperature sensor (turbo).
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>INTAKE AIR TEMPERATURE SENSOR(w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON for 1 second.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the intake air temperature sensor (turbo) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C18-2 or C113-3 (THIA) - Body ground | Always | 10 kΩ or higher |
Reconnect the intake air temperature sensor (turbo) connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT