Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P1608  Engine Lack of Power  


DESCRIPTION

This DTC is stored if engine output decreases due to a malfunction in the intake or exhaust system, fuel system or cooling system.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1608 Engine Lack of Power With the accelerator pedal fully depressed, engine output decreases for approximately 4 to 10 seconds due to a broken component in the intake or exhaust system, fuel system or cooling system or malfunction in one of those systems.
(1 trip detection logic)
·

Intake system clogged

·

EGR valve stuck closed

·

Deterioration of mass air flow meter (foreign matter present on sensor element etc.)

·

Intake system hose disconnected or cracked

·

Turbocharger sub-assembly vane stuck fully open

·

Manifold absolute pressure sensor

·

Manifold absolute pressure sensor out of range

·

Atmospheric pressure sensor (built into ECM)

·

Suction control valve sticking

·

Fuel leak

·

Fuel pressure sensor (built into common rail assembly)

·

Engine coolant leak

·

Radiator assembly clogged

·

Engine coolant temperature sensor

·

Engine coolant temperature sensor out of range or stuck

·

Fuel filter element sub-assembly

·

Injector assembly

·

Fan


- DTC stored

CONFIRMATION DRIVING PATTERN

P1608
DTC Detection Drive Pattern -

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1608 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine lack of power on hesitation.

As the DTC can be stored as a result of certain user actions, even if the DTC is output, if the customer makes no mention of problems, clear the DTC without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data.

·
A301856
2.271,0.094 3.188,0.333 0.917,0.24 10 false DTC is stored 0.365,1.052 1.156,1.281 0.792,0.229 10 false 0.5 seconds 1.281,1.073 2.104,1.281 0.823,0.208 10 false 0.5 seconds 2.24,1.083 3.073,1.302 0.833,0.219 10 false 0.5 seconds 0.354,2.813 2.438,3.083 2.083,0.271 10 false Freeze frame data recorded point 0.219,2.479 0.375,2.677 0.156,0.198 10 false 1 1.177,2.479 1.333,2.677 0.156,0.198 10 false 2 2.125,2.469 2.281,2.667 0.156,0.198 10 false 3 2.719,2.656 2.875,2.854 0.156,0.198 10 false 4 3.073,2.479 3.229,2.677 0.156,0.198 10 false 5

The fourth set of freeze frame data is the data recorded when the DTC is stored.



PROCEDURE

1.DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 1))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Record the stored DTC and freeze frame data.

HINT:

This freeze frame data shows the actual engine conditions when engine rack of power trouble occurred.



Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1608)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1608)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P1608 is output A
P1608 and other DTCs are output B


HINT:

If any DTCs other than DTC P1608 are output, troubleshoot those DTCs first.




A

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)

B

3.DETERMINE CAUSE OF PROBLEM (CHECK FREEZE FRAME DATA AND SNAPSHOT)
a.

Determine the cause of the problem based on the freeze frame data recorded in Procedure 1.


MAF Low
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"MAF Low" in freeze frame data is ON Intake air volume introduced via the mass air flow meter is insufficient and fuel injection volume remains suppressed
·

Intake system clogged

·

EGR valve stuck closed

·

Deterioration of mass air flow meter sub-assembly (foreign matter present on sensor element etc.)


·

EGR fully closed learning

·

EGR Active Test


HINT:

Refer to Lack of Power or Hesitation for the inspection procedure.

Click here(Click here)



Boost Pressure Low
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Boost Pressure Low" in freeze frame data is ON Actual boost pressure is lower than the target boost pressure and fuel injection volume remains suppressed
·

Intake system hose disconnected or cracked

·

Turbocharger sub-assembly vane stuck fully open

·

Manifold absolute pressure sensor

·

Manifold absolute pressure sensor out of range

·

Atmospheric pressure sensor (built into ECM)

·

Abnormal pressure difference between the atmospheric pressure sensor and manifold absolute pressure sensor

·

EGR valve stuck closed


The possible malfunctioning areas can be narrowed down by checking "MAF/Estimate MAF Ratio" when "Boost Pressure Low" in the freeze frame data is ON
HINT:

Refer to Lack of Power or Hesitation for the inspection procedure.

Click here(Click here)



MAF/Estimate MAF Ratio
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"MAF/Estimate MAF Ratio" in freeze frame data is 1.4 or more Air that has passed through the mass air flow meter leaks, and the estimated intake air volume becomes less than the actual intake air volume. Intake air leak due to intake pipe disconnection or cracks between the turbocharger sub-assembly and intercooler assembly or between the intercooler assembly and intake manifold.
HINT:

Refer to Lack of Power or Hesitation for the inspection procedure.

Click here(Click here)


"MAF/Estimate MAF Ratio" in freeze frame data is below 0.6 Air that has not passed through the mass air flow meter is supplied to the engine, and the actual intake air volume becomes less than the estimated intake air volume. Air entering due to intake pipe disconnection or cracks between the turbocharger sub-assembly and intercooler assembly or between the intercooler assembly and intake manifold.

Common Rail Pressure Low
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Common Rail Pressure Low" in freeze frame data is ON Common-rail pressure remains below the target value.
·

Suction control valve sticking

·

Fuel leak

·

Fuel filter element sub-assembly clogged

·

Fuel pressure sensor (built into common rail assembly)


HINT:

Refer to Lack of Power or Hesitation for the inspection procedure.

Click here(Click here)



Engine Coolant Temp High
Judgment of Data List Values Problem Cause Normal Condition Diagnosis Note
"Engine Coolant Temp High" in freeze frame data is ON Coolant temperature remains high (overheating) and fuel injection volume remains suppressed.
·

Engine coolant leak

·

Radiator assembly clogged

·

Engine coolant temperature sensor

·

Engine coolant temperature sensor out of range or stuck

·

Fan


Cooling system including radiator assembly

HINT:

Perform the next inspection if there are no problems with the above items.


Result:
Proceed to
NEXT



NEXT