Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) J

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  Fuel Injection System  


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



PROCEDURE

1.CHECK INJECTOR COMPENSATION CODE
a.

Check the injector compensation code.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Learning Values Confirmation
50005 61 242
Result:
Result Proceed to
Except below A
Compensation codes of the installed injector assemblies are the same as the compensation codes registered in the ECM B




A

2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING

B

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
2.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 61 239

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 61 235

Result:
Proceed to
NEXT



NEXT

3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 3)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


d.
A176220
2.528,2.459 2.751,2.645 0.223,0.186 10 *1 2.068,2.748 2.352,2.542 false 2.352,2.542 2.465,2.542 false 0.13,0.104 0.353,0.29 0.223,0.186 10 *a
*1 Snapshot Button
*a Reference


Take a snapshot of the following Data List items.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting. The data in the list below is that of a normal vehicle, but as the data varies between individual vehicles, this data should only be used for reference.

·

Graphs like the ones shown below can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.

·

Check the Data List at idling and at 4000 rpm with no load after the engine is warmed up.




Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
4.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME)
a.

Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm with no load.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st A
Injection Volume is 7 mm3/st or less at 4000 rpm B
Except above C


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)

B

15.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME)

C

15.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME)
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION)
HINT:

Use this Active Test to help determine whether a cylinder has compression loss or not.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.

Powertrain > Engine > Active Test
Active Test Display
Check the Cylinder Compression
Data List Display
Engine Speed of Cyl #1
Engine Speed of Cyl #2
Engine Speed of Cyl #3
Engine Speed of Cyl #4
50004 61 111 492,493,494,495

d.

Check the engine speed during the Active Test.

Result:
Result Proceed to
Except below A
The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. B


HINT:

When cranking, if the speed of a cylinder is approximately 100 rpm more than the other cylinders, there is probably a complete loss of compression in that cylinder.




A

6.CHECK CYLINDER COMPRESSION PRESSURE

B

7.PERFORM PILOT QUANTITY LEARNING
6.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>2KD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION

HINT:

When compression is low, there may be cracks in the piston or the injector assembly may be installed improperly.



Result:
Proceed to
OK
NG



OK

7.PERFORM PILOT QUANTITY LEARNING

NG

10.CHECK AND REPLACE PARTIAL ENGINE ASSEMBLY
7.PERFORM PILOT QUANTITY LEARNING
a.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 61 235

Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
8.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
50003 61 368,369,370,371

e.

Read the values.

Standard:
Tester Display Engine Condition* Normal Value
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or more and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3.0 mm3/st A
Except above B


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

B

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
9.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR(w/ DPF)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

17.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
10.CHECK AND REPLACE PARTIAL ENGINE ASSEMBLY
a.

Check and replace the engine assembly.


Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
Target Pump SCV Current
50004 61 90 706,54,408

d.

Start the engine.


e.
A176220
2.073,2.75 2.354,2.542 false 2.354,2.542 2.469,2.542 false 2.531,2.458 2.75,2.646 0.219,0.188 10 false *1 0.125,0.104 0.344,0.292 0.219,0.188 10 false *a
*1 Snapshot Button
*a Reference


Take a snapshot with the intelligent tester during the Active Test.

HINT:

Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (Personal Computer) with Intelligent Viewer installed.



f.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749
3.406,2.427 3.521,2.094 3.521,2.094 3.594,2.094 false 4.406,2.656 5.01,2.479 5.01,2.479 5.073,2.479 false 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.25 3.938,4.167 3.938,4.167 4.073,4.167 false 0.083,1.427 1.469,1.604 1.385,0.177 10 false Active Test Operation 0.167,0.594 1.563,0.792 1.396,0.198 10 false Engine Speed (rpm) 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Pressure 3.646,2.01 5,2.177 1.354,0.167 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.833,2.833 0.708,0.406 10 false Less than 10000 kPa 3,4.271 3.688,4.438 0.688,0.167 10 false 2 seconds 5.125,2.396 6.042,2.781 0.917,0.385 10 false Abnormal Fuel Pressure 2.448,1.125 3.125,1.323 0.677,0.198 10 false Test Start 4.177,1.125 4.844,1.323 0.667,0.198 10 false Test Stop 5.625,1.125 6.302,1.323 0.677,0.198 10 false Test Start 2.208,1.823 2.979,2.271 0.771,0.448 10 false Normal Fuel Pressure 1.646,0.313 2.021,0.479 0.375,0.167 10 false 2000 1.885,0.875 2.052,1.042 0.167,0.167 10 false 0 1.75,1.344 2.073,1.51 0.323,0.167 10 false ON 1.698,1.583 2.021,1.75 0.323,0.167 10 false OFF 4.146,4.115 5.74,4.531 1.594,0.417 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa (102.0 kgf/cm2, 1451 psi).


Result:
Result Proceed to
NG A
OK* B


NOTICE:

*: Even when the results of the Active Test are normal, take a snapshot of vehicle data when the vehicle is accelerating. If "Fuel Press" does not follow "Target Common Rail Pressure", proceed to step 17.

If "Fuel Press" does not follow "Target Common Rail Pressure", the fuel filter may be clogged.


HINT:
·

"Target Common Rail Pressure" means target fuel pressure controlled by the ECM.

·

"Fuel Press" means actual fuel pressure in common rail assembly.

·

If the pressure discharge valve mounted on the common rail assembly is malfunctioning, the actual fuel pressure may change as indicated by "Pressure Discharge Valve Malfunctioning" in the illustration.

·

The pressure discharge valve operates to discharge fuel pressure when the internal pressure of the common rail exceeds the target fuel pressure.

·

There are 2 fuel pressure sensor circuits and both of them display the same value. If the difference between Fuel Press and Common Rail Press Sens 2 exceeds 10000 kPa (102 kgf/cm2, 1451 psi) for 2 seconds or more, it is necessary to inspect or repair the wiring for the fuel pressure sensor.





A

12.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)

B

22.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
12.INSPECT COMMON RAIL ASSEMBLY (PRESSURE DISCHARGE VALVE)
a.

Enter the following menus: Powertrain / Engine and ECT / Utility / Pressure Discharge Valve Check.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION

Powertrain > Engine > Utility
Tester Display
Pressure Discharge Valve Check
50005 61 2109

b.

Select "Always Closed Check".


c.

Press "Next".


d.

Read the Value of fuel pressure values.

OK:

Fuel pressure is properly maintained.


HINT:
·

If the fuel pressure cannot be maintained, the pressure discharge valve may not have a tight seal.

·

If the fuel pressure is being properly maintained, there are no problems with the sealing properties of the high-pressure fuel system. Therefore, an insufficient supply of fuel due to the fuel filter being clogged, or squashed or blocked low-pressure fuel pipes or hoses may be causing the reduction in common rail pressure.




Result:
Proceed to
OK
NG



OK

13.INSPECT CLOGGED FUEL PIPE

NG

20.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRESSURE DISCHARGE VALVE)
13.INSPECT CLOGGED FUEL PIPE
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Injection.


d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Common Rail Pressure and Fuel Press value.

A261221
0.177,1.708 1.167,2.156 0.99,0.448 10 false Target Common Rail Pressure 3.854,2.125 5.073,2.406 1.219,0.281 10 false Normal Fuel Press 3.75,0.438 5.302,0.656 1.552,0.219 10 false Abnormal Fuel Press*1 0.115,0.115 1.823,0.354 1.708,0.24 10 false Fuel Pressure During Idling 1.083,2.406 3.583,2.844 2.5,0.438 10 false Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.104 7.083,1.958 1.177,0.854 10 false Normal Condition: +/- 5000 kPa (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Fuel Press" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter.





A

14.REPAIR OR REPLACE CLOGGED FUEL LINE

B

23.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
14.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element sub-assembly.

HINT:

If "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element sub-assembly.



Result:
Proceed to
NEXT



NEXT

21.BLEED AIR FROM FUEL SYSTEM
15.READ VALUE USING INTELLIGENT TESTER (INJECTION VOLUME)
a.

Check Injection Volume in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Injection Volume while idling after engine warm up is 9 mm3/st or more A
Except above B


HINT:

Check that PM forced regeneration was not being performed.

The idling speed during PM forced regeneration is 850 to 950 rpm (with the shift lever in neutral).




A

16.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS

B

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
16.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies of all cylinders

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR(w/ DPF)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

17.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
17.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

18.BLEED AIR FROM FUEL SYSTEM
18.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

19.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
19.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

Register the injector compensation codes.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Injector Compensation
50005 61 239

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION

Powertrain > Engine > Utility
Tester Display
Pilot Quantity Learning
50005 61 235

Result:
Proceed to
NEXT



NEXT

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (TEST THE FUEL LEAK)
20.REPLACE FUEL SUPPLY PUMP ASSEMBLY (PRESSURE DISCHARGE VALVE)
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>COMMON RAIL(w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

21.BLEED AIR FROM FUEL SYSTEM
21.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

22.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
22.READ VALUE USING INTELLIGENT TESTER (INJECTION FEEDBACK VAL #1 TO #4)
a.

Check Fuel Press and Target Common Rail Pressure in the snapshot taken in procedure 3 when the engine was idling.

Result:
Result Proceed to
Difference between Fuel Press and Target Common Rail Pressure is 5000 kPa (51.0 kgf/cm2, 725 psi) or more B
Except above A




A

END

B

23.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
23.REPLACE INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP(w/ DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

24.BLEED AIR FROM FUEL SYSTEM
24.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

25.PERFORM SUPPLY PUMP INITIALIZATION
25.PERFORM SUPPLY PUMP INITIALIZATION
a.

Perform supply pump initialization.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION

Powertrain > Engine > Utility
Tester Display
Supply Pump Initialization
50005 61 163

Result:
Proceed to
NEXT



NEXT

26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
26.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END