Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0505  Idle Control System Malfunction  


DESCRIPTION

The idling speed is controlled by the ETCS (Electronic Throttle Control System). The ETCS is comprised of: 1) a one-valve type throttle body; 2) the throttle actuator, which operates the throttle valve; 3) the throttle position sensor, which detects the opening angle of the throttle valve; 4) the accelerator pedal position sensor, which detects the accelerator pedal position; and 5) the ECM, which controls the ETCS. Based on the target idling speed, the ECM controls the throttle actuator to provide the proper throttle valve opening angle.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0505 Idle Control System Malfunction Idling speed continues to vary greatly from the target idling speed (2 trip detection logic).
·

ETCS

·

Air induction system

·

PCV hose connections

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors the idling speed and idling air flow volume to conduct Idle Speed Control (ISC). The ECM determines that the ISC system is malfunctioning if the following condition is met:

·

After driving at a vehicle speed of 10 km/h (6.25 mph) or more, the difference between the target and actual engine idling speed exceeds the threshold 5 times or more during a driving cycle, and then the system determines that the IAC flow rate learned value is stuck at the upper or lower limit, or that the IAC flow rate learned value has been changed by an amount that exceeds the threshold.


A121611
0.104,0.052 0.854,0.271 0.75,0.219 10 false Example: 0.448,1.198 1.458,1.427 1.01,0.229 10 false Idling Speed 1.948,2.063 3.135,2.26 1.188,0.198 10 false Target Speed 2.854,3.688 3.333,3.885 0.479,0.198 10 false Time 5.917,3.823 6.396,4.021 0.479,0.198 10 false Time 3.938,3.281 4.417,3.479 0.479,0.198 10 false Small 3.938,1.75 4.469,2 0.531,0.25 10 false Large 3.625,1.094 5.719,1.375 2.094,0.281 10 false Learned Idling Air Volume 5.927,1.427 6.781,1.729 0.854,0.302 10 false Maximum 5.927,3 6.76,3.198 0.833,0.198 10 false Minimum 4.219,2.5 4.396,2.698 0.177,0.198 10 false 0 1.885,3.073 3.448,3.271 1.563,0.198 10 false Actual Idling Speed

MONITOR STRATEGY

Required Sensors/Components (Main) ETCS
Required Sensors/Components (Related) Crankshaft position sensor, Engine coolant temperature sensor, and Vehicle speed sensor
Frequency of Operation Once per driving cycle
MIL Operation 2 driving cycles

TYPICAL MALFUNCTION THRESHOLDS

Both of following conditions A and B met -
A. Number of times that both of following conditions (a) and (b) met 5 times or more
(a) Engine speed - Target engine speed Less than -100 rpm, or more than 150 rpm (A/C off and NSW off)
Less than -100 rpm, or more than 200 rpm (A/C on or NSW on)
(b) Vehicle condition Stopped after being driven at 10 km/h (6.25 mph) or more
B. Either condition is met (c) or (d)
(c) IAC flow rate learned value Lower limit or upper limit
(d) Amount of change of IAC flow rate learned value exceeds threshold -

CONFIRMATION DRIVING PATTERN

A232053
4.521,2.958 4.844,3.375 4.844,3.375 3.99,2.958 false 5.74,2.948 5.104,3.333 5.104,3.333 5.125,2.948 false 2.833,2.958 2.615,3.229 false 3.188,2.948 2.573,3.51 false 0.604,1.219 1.875,1.521 1.271,0.302 10 false 10 km/h (6.25 mph) 1.479,2.042 1.875,2.323 0.396,0.281 10 false Idling 0.667,2.396 2.01,2.771 1.344,0.375 10 false Ignition Switch ON 2.333,2.531 2.635,2.771 0.302,0.24 10 false [A] 2.75,2.24 3.083,2.448 0.333,0.208 10 false [B] 6.292,3.333 6.594,3.573 0.302,0.24 10 false [E] 2.344,3.531 3.51,3.719 1.167,0.188 10 false 1 minute or more 4.563,3.385 5.969,3.615 1.406,0.229 10 false 20 seconds or more 3.615,0.979 3.865,1.177 0.25,0.198 10 false [D] 5.917,0.969 6.167,1.167 0.25,0.198 10 false [D] 5.354,0.969 5.604,1.167 0.25,0.198 10 false [D] 4.771,0.969 5.021,1.167 0.25,0.198 10 false [D] 4.198,0.979 4.448,1.177 0.25,0.198 10 false [D] 3.104,2.24 3.427,2.531 0.323,0.292 10 false [C] 1.854,3.177 2.656,3.396 0.802,0.219 10 false Warming up

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

Idle the engine for 1 minute or more [C].

HINT:

In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.


8.

Accelerate the vehicle to 10 km/h (6.25 mph) or more, and then idle the engine for 20 seconds or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Repeat step [D] 5 times.

10.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0505.

14.

Check the DTC judgment result.

Intelligent tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E] again.




CAUTION / NOTICE / HINT

HINT:
·

The following conditions may also cause DTC P0505 to be stored:

1.

The floor carpet overlapping slightly onto the accelerator pedal, causing the accelerator pedal to be slightly depressed and therefore the throttle valve position to be slightly open.

2.

The accelerator pedal being not fully released.


·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0505)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0505 is output A
P0505 and other DTCs are output B


HINT:

If any DTCs other than P0505 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2TR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/ Secondary Air Injection System)>ON-VEHICLE INSPECTION

OK:

PCV hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK AIR INDUCTION SYSTEM

NG

3.CHECK AIR INDUCTION SYSTEM
a.

Check the air induction system for vacuum leaks.

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in air induction system.



Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE AIR INDUCTION SYSTEM

4.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Check for contamination between the throttle valve and housing, and check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.



Result:
Proceed to
OK
NG



OK

5.CONFIRM WHETHER DTC OUTPUT RECURS

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

5.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
P0505 is output A
No DTC is output B




A

B

END