Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0560  System Voltage  


DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0560 System Voltage Open in the ECM backup power source circuit (1 trip detection logic).
·

Open in backup power source circuit

·

Battery

·

Battery terminals

·

EFI fuse

·

ECM


Comes on DTC stored

HINT:

If DTC P0560 is stored, the ECM does not store other DTCs and the data stored in the ECM is partly cleared.


MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

Stand-by RAM Initialized
ECM power source Below 3.5 V

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

A247776
0.906,2.531 1.458,3 0.552,0.469 10 false Battery 1.781,0.927 2.354,1.167 0.573,0.24 10 false BATT P/I 4.021,0.906 4.323,1.115 0.302,0.208 10 false EFI 5.615,0.531 5.729,0.708 0.115,0.177 10 false 3 5.51,0.75 5.833,0.938 0.323,0.188 10 false G89 5.615,1.875 5.729,2.042 0.115,0.167 10 false 3 5.521,2.063 5.865,2.281 0.344,0.219 10 false C75 5.865,0.885 6.25,1.104 0.385,0.219 10 false BATT 5.865,2.052 6.094,2.26 0.229,0.208 10 false E1 6.188,2.896 6.531,3.063 0.344,0.167 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G89-3 (BATT) - Positive (+) battery cable terminal Always Below 1 Ω
G89-3 (BATT) or Positive (+) battery cable terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

Click herePower Source / Network>2TR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR BATTERY TERMINAL

4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON and turn the intelligent tester on.


g.

Wait 5 seconds or more.


h.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

i.

Read the DTCs.

Result:
Result Proceed to
P0560 is output A
No DTC is output B




A

B