Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic).

(a) Vehicle speed is 20 km/h (12.4 mph) or more.

(b) Engine speed is 1000 rpm or more.

(c) STA signal is on.


·

Starter (ST) relay circuit

·

Ignition switch assembly

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) Starter (ST) relay, Ignition switch assembly
Required Sensors/Components (Related) Vehicle speed sensor, Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A231469
1.24,1.979 1.615,2.156 0.375,0.177 10 false Idling 0.438,2.25 1.635,2.604 1.198,0.354 10 false Ignition Switch ON 0.438,0.813 1.615,1.073 1.177,0.26 10 false 24 km/h (15 mph) 2.396,2.854 3.104,3.208 0.708,0.354 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.26,2.625 0.26,0.292 10 false [A] 2.583,2.125 2.792,2.354 0.208,0.229 10 false [B] 4.031,0.458 4.25,0.688 0.219,0.229 10 false [C] 4.896,3.313 5.115,3.542 0.219,0.229 10 false [D]

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A254185
5.698,3.438 6.073,3.615 0.375,0.177 10 false STA 6.135,4.708 6.448,4.885 0.313,0.177 10 false G89 5.427,3.438 5.615,3.594 0.188,0.156 10 false 12 6.146,4.865 6.604,5.125 0.458,0.26 10 false ECM 0.594,4.625 1.083,4.865 0.49,0.24 10 false AM2 1.094,1.385 1.219,1.542 0.125,0.156 10 false 5 1.26,1.385 1.74,1.573 0.479,0.188 10 false AM2 1.854,1.385 2.208,1.563 0.354,0.177 10 false ST2 3.615,1.417 3.906,1.667 0.292,0.25 10 false ST 2.198,1.385 2.323,1.542 0.125,0.156 10 false 7 1.229,1.708 1.573,1.885 0.344,0.177 10 false G9 1.229,1.854 2.25,2.094 1.021,0.24 10 false Ignition Switch 3.26,4.365 3.583,4.635 0.323,0.271 10 false ST 3,3.906 3.125,4.063 0.125,0.156 10 false 2 3.01,4.823 3.135,4.979 0.125,0.156 10 false 1 2.573,3.906 2.698,4.063 0.125,0.156 10 false 5 2.563,4.823 2.688,4.979 0.125,0.156 10 false 3 1.969,5.469 2.24,5.667 0.271,0.198 10 false C32 1.813,5.458 1.938,5.625 0.125,0.167 10 false 1 1.344,5.5 1.469,5.667 0.125,0.167 10 false 1 1.292,5.698 1.542,5.896 0.25,0.198 10 false D3 1.698,6.479 2.208,6.729 0.51,0.25 10 false Starter 0.729,6.583 1.26,6.833 0.531,0.25 10 false Battery

CAUTION / NOTICE / HINT

HINT:
·

The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.

If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>PROBLEM SYMPTOMS TABLE).

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Check the value displayed on the intelligent tester when the ignition switch is turned to ON and when the engine is started.

OK:
Condition Starter Signal
Ignition switch turned to ON Close
Engine started Open



Result:
Proceed to
OK
NG



OK

NG

2.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - ECM)
2.REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - ECM)
a.

Repair or replace harness and connector (ignition switch - ECM)


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS
3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Drive the vehicle at more than 24 km/h (15 mph) for more than 20 seconds.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
P0617 is output A
No DTC is output B




A

B

END