1.PERFORM IGNITION COIL AND SPARK TEST
Check for DTCs (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DTC CHECK / CLEAR).
If a DTC is output, perform troubleshooting procedures for that DTC.
Check if sparks occur.
Remove the ignition coils and spark plugs (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL).
Install the spark plug to the ignition coil and connect the ignition coil connector.
Disconnect the 4 injector connectors.
Ground the spark plug.
Visually check that sparks occur while the engine is being cranked.
Be sure to ground the spark plug when checking.
If the ignition coil has been struck or dropped, replace it.
Do not crank the engine for more than 2 seconds.
Spark test procedure.
Check that the wire harness side connector of the ignition coil with igniter is securely connected.
| Result | Proceed to |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on each ignition coil with igniter.
1. Replace the ignition coil with igniter with a normal one.
2. Perform a spark test again.
| Result | Proceed to |
|---|---|
| NG | Replace ignition coil with igniter |
| OK | Go to next step |
Check the spark plug.
| Result | Proceed to |
|---|---|
| NG | Replace spark plug |
| OK | Go to next step |
Check the power supply to the ignition coil with igniter.
1. Turn the ignition switch to ON.
2. Check that there is battery voltage at the ignition coil positive (+) terminal.
| Result | Procedure |
|---|---|
| NG | Check wiring between ignition switch and ignition coil with igniter |
| OK | Go to next step |
Check the camshaft position sensor (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0340).
Check the crankshaft position sensor (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0335).
Check the IGT signal circuit (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0351).
Connect the 4 injector connectors.
Install the 4 ignition coils and 4 spark plugs (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION).
2.INSPECT SPARK PLUG
Do not use a wire brush for cleaning.
Do not attempt to adjust the electrode gap of a used spark plug.
| *1 | Body Ground |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Spark plug (terminal part) - Body ground | Always | 10 MΩ or higher |
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Quickly accelerate the engine to 4000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage on its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.
| Manufacturer | Product |
|---|---|
| DENSO | K20HR-U11 |
Check and adjust the spark plug electrode gap.
1.0 to 1.1 mm (0.0394 to 0.0433 in.)
1.3 mm (0.0512 in.)
If the gap is more than the maximum, replace the spark plug.
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner, and then dry it.
588 kPa (6.0 kgf/cm2, 85 psi)
20 seconds or less
Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.