Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › RELAY
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052089 RELAY G

2TR-FE ENGINE CONTROL  RELAY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT NO. 1 INTEGRATION RELAY (MAIN)

a.

Check the EFI fuse.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω


If the result is not as specified, replace the EFI fuse.



b.
A225101
2.354,1.563 2.719,1.781 0.365,0.219 1.208,1.563 1.573,1.781 0.365,0.219 0.323,1.563 0.688,1.76 0.365,0.198 2.469,1.594 2.813,1.833 0.344,0.24 10 false 1I 1.333,1.583 1.594,1.802 0.26,0.219 10 false 1J 0.406,1.583 0.729,1.823 0.323,0.24 10 false 1H 0.177,0.146 0.406,0.375 0.229,0.229 10 false *a
*a Component without harness connected
(No. 1 Integration Relay)


Check the MAIN relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-1 - 1J-4 Battery voltage not applied to terminals 1J-2 and 1J-3 10 kΩ or higher
Battery voltage applied to terminals 1J-2 and 1J-3 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.



Hide 2.INSPECT NO. 1 INTEGRATION RELAY (C/OPN)

A225101
2.354,1.563 2.719,1.781 0.365,0.219 1.208,1.563 1.573,1.781 0.365,0.219 0.323,1.563 0.688,1.76 0.365,0.198 2.469,1.594 2.813,1.833 0.344,0.24 10 false 1I 1.333,1.583 1.594,1.802 0.26,0.219 10 false 1J 0.406,1.583 0.729,1.823 0.323,0.24 10 false 1H 0.177,0.146 0.406,0.375 0.229,0.229 10 false *a
*a Component without harness connected
(No. 1 Integration Relay)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-5 - 1J-8 Battery voltage not applied to terminals 1J-6 and 1J-7 10 kΩ or higher
Battery voltage applied to terminals 1J-6 and 1J-7 Below 1 Ω


If the result is not as specified, replace the No. 1 integration relay.


Hide 3.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F) (w/ Secondary Air Injection System)

a.
A184106
2.531,1.125 2.927,1.125 false 2.531,1.625 2.938,1.625 false 1.573,0.135 1.698,0.135 1.698,0.135 2.042,0.573 false 3.031,0.125 2.906,0.125 2.906,0.125 2.615,0.583 false 0.208,0.771 0.417,0.948 0.208,0.177 10 false 3 1.208,0.781 1.406,0.958 0.198,0.177 10 false 5 0.208,1.323 0.365,1.5 0.156,0.177 10 false 2 1.208,1.323 1.438,1.5 0.229,0.177 10 false 1 3,1.552 3.208,1.729 0.208,0.177 10 false 3 3,1.052 3.198,1.229 0.198,0.177 10 false 5 3.094,0.042 3.25,0.219 0.156,0.177 10 false 2 1.417,0.042 1.646,0.219 0.229,0.177 10 false 1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω


If the result is not as specified, replace the air fuel ratio sensor heater relay.