Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

The throttle position sensor is mounted on the throttle body and detects the opening angle of the throttle valve. This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air-fuel ratio correction, power increase correction and fuel-cut control.

A297617
0.896,1.896 1.135,1.083 true 0.865,2.229 0.802,1.625 true 0.49,3.104 0.844,2.594 true 1.177,3.552 0.865,2.958 true 4.385,1.521 4.781,1.042 4.781,1.042 4.938,1.042 true 6.229,1.813 6.094,0.49 6.094,0.49 5.958,0.49 true 5.844,2.427 5.542,2.229 true 0.125,0.563 1.688,0.781 1.563,0.219 10 false Throttle Position Sensor 1.177,0.969 1.719,1.167 0.542,0.198 10 false Magnet 1.99,1.125 2.531,1.323 0.542,0.198 10 false ECM 0.292,1.51 0.854,1.708 0.563,0.198 10 false IC No. 1 0.292,3.125 0.854,3.323 0.563,0.198 10 false IC No. 2 1.25,3.49 2.167,3.688 0.917,0.198 10 false Magnet 1.302,1.74 1.917,1.938 0.615,0.198 10 false VC 1.302,2.073 1.917,2.271 0.615,0.198 10 false VTA1 1.313,2.427 1.927,2.625 0.615,0.198 10 false VTA2 1.323,2.76 1.781,2.958 0.458,0.198 10 false E2 2.885,0.969 4.573,1.208 1.688,0.24 10 false Sensor Output Voltage (V) 4.333,0.417 6.063,0.656 1.729,0.24 10 false Line indicating VTA2 x 0.8 4.99,0.958 5.979,1.188 0.99,0.229 10 false Fail-safe Angle 5.917,2.396 6.396,2.594 0.479,0.198 10 false 1.11 V 4.563,1.885 5.042,2.083 0.479,0.198 10 false VTA2 4.896,2.729 5.375,2.927 0.479,0.198 10 false VTA1 3.969,1.458 4.198,1.646 0.229,0.188 10 false 5.0 3.906,1.677 4.208,1.865 0.302,0.188 10 false 4.65 3.802,2.229 4.24,2.417 0.438,0.188 10 false 2.58* 3.854,2.385 4.219,2.552 0.365,0.167 10 false 2.25 3.792,2.729 4.177,2.927 0.385,0.198 10 false 0.95* 3.844,2.896 4.229,3.094 0.385,0.198 10 false 0.69 4.292,3.125 4.677,3.323 0.385,0.198 10 false 6.5° 4.177,3.469 4.563,3.667 0.385,0.198 10 false 0° 6.5,3.469 6.74,3.656 0.24,0.188 10 false 84° 4.885,3.375 5.823,3.615 0.938,0.24 10 false Usable Range 5.042,3.74 7.01,4.073 1.969,0.333 10 false Throttle Valve Opening Angle (°) 4.594,4.156 6.563,4.49 1.969,0.333 10 false *: During fail-safe control 0.156,3.844 1.073,4.042 0.917,0.198 10 false Note: 0.156,4.042 3.344,4.448 3.188,0.406 10 false The throttle valve opening angle transmitted through sensor terminal VTA1 is expressed as a percentage. 0.167,4.792 3.323,5.198 3.156,0.406 10 false Between 10% and 22%: Throttle valve fully closed 0.156,5.24 3.229,5.573 3.073,0.333 10 false Between 66% and 98%: Throttle valve fully open 0.156,5.646 3.229,5.979 3.073,0.333 10 false Approximately 19%: Fail-safe angle (6.5°) 3.698,4.677 5.938,4.969 2.24,0.292 10 false Characteristics of sensor output: 3.708,5.042 7.083,5.427 3.375,0.385 10 false VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction Output voltage of VTA1 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored
P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem Difference between VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


Comes on DTC stored
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input Output voltage of VTA1 is 0.2 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input Output voltage of VTA1 is 4.8 V or higher for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in E2 circuit

·

Short between VC and VTA1 circuits

·

ECM


Comes on DTC stored
P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit Output voltage of VTA2 quickly fluctuates beyond the lower and upper malfunction thresholds for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored
P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input Output voltage of VTA2 is 0.5 V or less for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input Output voltage of VTA2 is 4.8 V or higher, and VTA1 is between 0.2 V and 1.8 V for 2 seconds when the accelerator pedal is depressed (1 trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in E2 circuit

·

Short between VC and VTA2 circuits

·

ECM


Comes on DTC stored
P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation Either condition is met (1 trip detection logic):
(a) Difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) Output voltage of VTA1 is 0.2 V or less, and VTA2 is 0.5 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored

HINT:
·

When any of these DTCs is stored, check the throttle valve opening angle by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.


·

Throttle Position No. 1 is the VTA1 signal, and Throttle Position No. 2 is the VTA2 signal.

Reference (Normal Condition):
Intelligent Tester Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No. 1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No. 2 2.1 to 3.1 V 4.6 to 4.98 V




MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm that the throttle position sensor is operating properly.

P0120, P0122, P0123, P0220, P0222, P0223 and P2135
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor and stores a DTC.


If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

P0121

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm that the throttle position sensor and VTA1 are operating properly.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction of the throttle position sensor. The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 2 seconds after the engine is next started.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A198824
3.698,1.396 3.333,0.406 3.333,0.406 3.563,0.406 false 2.615,1.99 2.354,1.25 2.354,1.25 2.521,1.25 false 4.938,1.99 5.271,1.146 5.271,1.146 5.375,1.146 false 1.229,1.875 1.75,2.125 0.521,0.25 10 false Idling 0.417,2.146 1.771,2.417 1.354,0.271 10 false Ignition Switch ON 2.115,2.021 2.438,2.24 0.323,0.219 10 false [A] 3.844,1.76 4.24,2.063 0.396,0.302 10 false [B] 5.438,1.073 6.25,1.302 0.813,0.229 10 false Released 3.625,0.313 4.563,0.594 0.938,0.281 10 false Depressed 4.438,2.615 5.25,2.875 0.813,0.26 10 false 2 seconds 4.708,1.719 5.052,1.979 0.344,0.26 10 false [C] 5.021,2.969 5.375,3.26 0.354,0.292 10 false [D] 2.583,1.177 3.354,1.417 0.771,0.24 10 false Released

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress and release the accelerator pedal [B].

8.

Idle the engine for 2 seconds or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0120, P0121, P0122, P0123, P0220, P0222, P0223 or P2135.

13.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.




FAIL-SAFE

When any of these DTCs as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A240397
0.417,2.854 0.906,3.073 0.49,0.219 10 false C67 0.406,3.01 2.323,3.365 1.917,0.354 10 false Throttle Body with Motor 1.104,0.656 1.281,0.823 0.177,0.167 10 false IC 1.104,1.552 1.281,1.719 0.177,0.167 10 false IC 1.635,0.469 2.292,0.875 0.656,0.406 10 false VTA 1.708,1.031 2.115,1.26 0.406,0.229 10 false VC 1.563,1.573 2.083,1.823 0.521,0.25 10 false VTA2 1.719,2.146 2.188,2.458 0.469,0.313 10 false E2 5.583,0.469 6.208,0.719 0.625,0.25 10 false VTA1 5.583,1.031 5.948,1.271 0.365,0.24 10 false VC 5.583,1.573 6.167,1.885 0.583,0.313 10 false VTA2 5.583,2.146 5.958,2.396 0.375,0.25 10 false E2 1.99,0.458 2.104,0.615 0.115,0.156 10 false 6 1.99,1 2.094,1.177 0.104,0.177 10 false 5 1.979,1.552 2.094,1.75 0.115,0.198 10 false 4 1.979,2.125 2.094,2.292 0.115,0.167 10 false 3 5.99,2.854 6.292,3.052 0.302,0.198 10 false C75 5.333,0.458 5.656,0.708 0.323,0.25 10 false 20 5.333,1.021 5.688,1.271 0.354,0.25 10 false 18 5.333,1.552 5.615,1.75 0.281,0.198 10 false 19 5.333,2.146 5.688,2.427 0.354,0.281 10 false 28 5.99,3 6.479,3.271 0.49,0.271 10 false ECM

CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the throttle position sensor.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Throttle Position No. 1 and Throttle Position No. 2.

Powertrain > Engine > Data List
Tester Display
Throttle Position No.1
Throttle Position No.2
50003 61 112,113

e.

Check the values displayed on the intelligent tester.

Result:
Throttle Position No. 1 (VTA1)
When Accelerator Pedal Released
Throttle Position No. 2 (VTA2)
When Accelerator Pedal Released
Throttle Position No. 1 (VTA1)
When Accelerator Pedal Depressed
Throttle Position No. 2 (VTA2)
When Accelerator Pedal Depressed
Trouble Area Proceed to
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V E2 circuit open
0 to 0.2 V, or 4.5 to 5.0 V 2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 5.0 V 2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or shorted to ground
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 5.0 V 0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 5.0 V VTA2 circuit open or shorted to ground
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
TP sensor circuit normal B


HINT:
·

DTC P0121 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No. 1

VTA2: Throttle Position No. 2


·

If DTC P0121 is output, proceed to "Check Harness and Connector (Throttle Position Sensor - ECM)".





A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body with motor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C67-5 (VC) - C75-18 (VC) Always Below 1 Ω
C67-6 (VTA) - C75-20 (VTA1) Always Below 1 Ω
C67-4 (VTA2) - C75-19 (VTA2) Always Below 1 Ω
C67-3 (E2) - C75-28 (E2) Always Below 1 Ω
C67-5 (VC) or C75-18 (VC) - Body ground Always 10 kΩ or higher
C67-6 (VTA) or C75-20 (VTA1) - Body ground Always 10 kΩ or higher
C67-4 (VTA2) or C75-19 (VTA2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
a.
A107895
0.479,1.042 0.969,1.333 0.49,0.292 1.302,1.781 1.625,1.417 false 2.219,1.802 1.938,1.417 false 0.042,0.01 0.333,0.26 0.292,0.25 10 false *a 1.135,1.813 1.448,2.042 0.313,0.229 10 false E2 2.156,1.813 2.49,2.042 0.333,0.229 10 false VC 0.615,1.104 0.948,1.323 0.333,0.219 10 false C67
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


Disconnect the throttle body with motor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C67-5 (VC) - C67-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the output DTCs.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output A
No DTC is output B




A

B

END