Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0340  Camshaft Position Sensor Circuit Malfunction  P0341  Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed on the cylinder head. When the camshaft rotates, each of the 3 teeth on the camshaft pass through the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to locate the camshaft position. This signal is then used to control ignition timing, fuel injection timing, and the VVT system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction When one of the following conditions is met:
·

No camshaft position sensor signal is sent to the ECM while cranking (1 trip detection logic).

·

The camshaft position sensor signal is missing despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing gear assembly

·

Timing chain for intake camshaft jumped tooth

·

ECM


Comes on DTC stored
P0341 Camshaft Position Sensor "A" Circuit Range / Performance (Bank 1 or Single Sensor) While the crankshaft rotates twice, the camshaft position sensor signal is input to the ECM 12 times or more (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Camshaft timing gear assembly

·

Timing chain for intake camshaft jumped tooth

·

ECM


Comes on DTC stored

HINT:
·

DTC P0340 indicates a malfunction related to the camshaft position sensor (+) circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).

·

DTC P0341 indicates a malfunction related to the camshaft position sensor (-) circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).



A063955
2.802,0.604 3.219,0.813 0.417,0.208 10 false GND 2.802,1.417 3.219,1.625 0.417,0.208 10 false GND 0.281,0.625 0.563,0.813 0.281,0.188 10 false G2 0.281,1.427 0.677,1.615 0.396,0.188 10 false NE 1.198,1.958 2.229,2.135 1.031,0.177 10 false 20 msec./DIV. 2.75,0.083 3.427,0.313 0.677,0.229 10 false 5 V/DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

G2 stands for the camshaft position sensor signal and NE stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Tester Connection Tool Setting Condition Specified Condition
C75-27 (NE+) - C75-34 (NE-) 5 V/DIV, 20 ms/DIV Idling The correct waveform is as shown
C75-26 (G2) - C75-34 (NE-) 5 V/DIV, 20 ms/DIV Idling The correct waveform is as shown


MONITOR DESCRIPTION

P0340:

If no signal is transmitted by the camshaft position sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the circuit.


P0341:

If the G signal is input 12 or more times in the time it takes for the signal indicating top dead center to be input 3 times, the ECM interprets this as a malfunction of the circuit.


MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A240393
0.622,1.775 2.289,1.941 1.667,0.166 10 Camshaft Position Sensor 5.657,2.252 6.016,2.417 0.36,0.166 10 ECM 0.622,1.621 0.926,1.787 0.304,0.166 10 C68 5.081,0.731 5.263,0.874 0.182,0.142 10 26 5.081,1.507 5.265,1.649 0.184,0.142 10 34 5.657,2.104 5.94,2.263 0.284,0.159 10 C75 5.341,0.708 5.636,0.857 0.295,0.149 10 G2 5.341,1.541 5.636,1.691 0.295,0.149 10 NE- 1.761,0.736 1.862,0.899 0.101,0.163 10 1 1.761,1.494 1.878,1.657 0.118,0.163 10 2 3.23,1.728 3.805,1.912 0.574,0.184 10 Shielded

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C68-1 - C75-26 (G2) Always Below 1 Ω
C68-2 - C75-34 (NE-) Always Below 1 Ω
C68-1 or C75-26 (G2) - Body ground Always 10 kΩ or higher
C68-2 or C75-34 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
BR03795
1.594,1.583 2.448,1.854 0.854,0.271 10 Clearance 0.438,1.76 0.792,1.99 0.354,0.229 10 OK 2.656,1.771 2.979,2.0 0.323,0.229 10 NG

Check the camshaft position sensor.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH)

NG

4.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (TEETH)
a.

Check the teeth of the camshaft timing gear assembly.

OK:

Teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

5.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine and idle it for 10 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
P0340 or P0341 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B