Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) U

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  TERMINALS OF ECM  


CHECK ECM


G035135
1.302,0.073 1.635,0.26 0.333,0.188 2.698,0.063 3.031,0.25 0.333,0.188 4.365,0.073 4.698,0.26 0.333,0.188 5.688,0.073 6.021,0.26 0.333,0.188 1.333,0.083 1.688,0.281 0.354,0.198 10 false C75 2.729,0.073 3.052,0.271 0.323,0.198 10 false C76 4.396,0.073 4.76,0.271 0.365,0.198 10 false G88 5.719,0.083 6.042,0.281 0.323,0.198 10 false G89

a.

Measure the voltage according to the value(s) in the table below.

HINT:

The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G89-3 (BATT) - C75-3 (E1) L - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
G89-7 (+BM) - C75-3 (E1) R-W - BR Power source of throttle actuator Always 11 to 14 V
G89-9 (IGSW) - C75-3 (E1) B-O - BR Ignition switch Ignition switch ON 11 to 14 V
G89-1 (+B) - C75-3 (E1) B - BR Power source of ECM Ignition switch ON 11 to 14 V
C75-13 (OC1+) - C75-12 (OC1-) P-L - Y Camshaft timing oil control valve Idling Pulse generation
(See waveform 1)
G89-8 (MREL) - C75-3 (E1) W-G - BR MAIN relay Ignition switch ON 11 to 14 V
C76-28 (VG) - C76-30 (E2G) L-W - L-R Mass air flow meter Idling, shift lever in P or N, A/C off 0.5 to 3.0 V
C76-29 (THA) - C75-28 (E2) L-B - BR Intake air temperature sensor Idling, intake air temperature 20°C (68°F) 0.5 to 3.4 V
C75-32 (THW) - C75-28 (E2) B - BR Engine coolant temperature sensor Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
C75-18 (VC) - C75-28 (E2) LG-B - BR Power source of throttle position sensor (fixed voltage) Ignition switch ON 4.5 to 5.5 V
C75-20 (VTA1) - C75-28 (E2) B-R - BR Throttle position sensor (for engine control) Ignition switch ON,
throttle valve fully closed
0.5 to 1.1 V
Ignition switch ON,
throttle valve fully open
3.2 to 4.8 V
C75-19 (VTA2) - C75-28 (E2) LG - BR Throttle position sensor (for sensor malfunction detection) Ignition switch ON,
throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON,
throttle valve fully open
4.6 to 5.0 V
G89-18 (VPA) - G89-20 (EPA) W-L - BR-W Accelerator pedal position sensor (for engine control) Ignition switch ON,
accelerator pedal released
0.5 to 1.1 V
Ignition switch ON,
accelerator pedal fully depressed
2.6 to 4.5 V
G89-19 (VPA2) - G89-21 (EPA2) GR-G - BR-Y Accelerator pedal position sensor (for sensor malfunction detection) Ignition switch ON,
accelerator pedal released
1.2 to 2.0 V
Ignition switch ON,
accelerator pedal fully depressed
3.4 to 5.3 V
G89-26 (VCPA) - G89-20 (EPA) LG-R - BR-W Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
G89-27 (VCP2) - G89-21 (EPA2) BR-R - BR-Y Power source of accelerator pedal position sensor (for VPA2) Ignition switch ON 4.5 to 5.5 V
C75-21 (A1A+) - C75-28 (E2) B - BR Heated oxygen sensor Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 2)
C75-1 (HA1A) - C76-4 (E03) Y - W-B Heated oxygen sensor heater Ignition switch ON 11 to 14 V
C76-6 (#10) - C75-7 (E01) L - W-B Fuel injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 3)
C76-5 (#20) - C75-7 (E01) G - W-B Fuel injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 3)
C76-2 (#30) - C75-7 (E01) R - W-B Fuel injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 3)
C76-1 (#40) - C75-7 (E01) W - W-B Fuel injector Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 3)
C75-29 (KNK1) - C75-30 (EKNK) B - W Knock sensor Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 4)
C75-26 (G2) - C75-34 (NE-) R - G Camshaft position sensor Idling Pulse generation
(See waveform 5)
C75-27 (NE+) - C75-34 (NE-) L - G Crankshaft position sensor Idling Pulse generation
(See waveform 5)
C75-17 (IGT1) - C75-3 (E1) R - BR Ignition coil (ignition signal) Idling Pulse generation
(See waveform 6)
C75-16 (IGT2) - C75-3 (E1) R-L - BR Ignition coil (ignition signal) Idling Pulse generation
(See waveform 6)
C75-15 (IGT3) - C75-3 (E1) G-B - BR Ignition coil (ignition signal) Idling Pulse generation
(See waveform 6)
C75-14 (IGT4) - C75-3 (E1) G - BR Ignition coil (ignition signal) Idling Pulse generation
(See waveform 6)
C75-23 (IGF1) - C75-3 (E1) G-R - BR Ignition coil (ignition confirmation signal) Ignition switch ON 4.5 to 5.5 V
Idling Pulse generation
(See waveform 6)
C76-23 (PRG) - C75-3 (E1) L - BR Purge VSV Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See waveform 7)
G88-8 (SPD) - C75-3 (E1) V-R - BR Speed signal from combination meter Driving at 20 km/h (12 mph) Pulse generation
(See waveform 8)
G89-12 (STA) - C75-3 (E1) L-Y - BR*1
B-Y - BR*2
Starter signal Cranking 6.0 V or higher
G89-30 (NSW) - C75-3 (E1)*2 L-Y - BR Park/neutral position switch Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 3.0 V
G88-4 (STP) - C75-3 (E1) G-W - BR Stop light switch Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
G89-16 (ST1-) - C75-3 (E1) R-L - BR Stop light switch
(opposite to voltage at STP terminal)
Ignition switch ON,
brake pedal depressed
Below 1.5 V
Ignition switch ON,
brake pedal released
7.5 to 14 V
C75-5 (M+) - C76-3 (ME01) B - W-B Throttle actuator Idling with warm engine Pulse generation
(See waveform 9)
C75-4 (M-) - C76-3 (ME01) W - W-B Throttle actuator Idling with warm engine Pulse generation
(See waveform 10)
G89-25 (FC) - C75-3 (E1) LG-B - BR Fuel pump control Ignition switch ON 11 to 14 V
G88-30 (W) - C75-3 (E1) R-B - BR MIL Ignition switch ON Below 3.0 V
Idling 11 to 14 V
G88-17 (TC) - C75-3 (E1) P-B - BR Terminal TC of DLC3 Ignition switch ON 11 to 14 V
G88-1 (TACH) - C75-3 (E1) B-W - BR Engine speed Idling Pulse generation
(See waveform 11)
C75-10 (ALT) - C75-3 (E1) G - BR Generator Ignition switch ON 11 to 14 V
G89-15 (ELS) - C75-3 (E1) G - BR Electric load Taillight switch on 7.5 to 14 V
Taillight switch off Below 1.5 V
G88-3 (ELS3) - C75-3 (E1) B - BR Electric load Defogger switch on 7.5 to 14 V
Defogger switch off Below 1.5 V
G88-14 (THWO) - C75-3 (E1) P - BR Engine speed signal sent to combination meter Idling with warm engine Pulse generation
G88-32 (F/PS) - C75-3 (E1) B - BR Center airbag sensor assembly Ignition switch on Pulse generation
C76-32 (PSW) - C75-3 (E1) G-Y - BR Power steering oil pressure switch While turning steering wheel Below 1.5 V

*1: for Manual Transmission

*2: for Automatic Transmission



b.
A303302
0.458,0.26 1.208,0.458 0.75,0.198 10 false 5 V/DIV. 0.583,1.115 1.021,1.313 0.438,0.198 10 false GND 1.719,1.865 2.604,2.063 0.885,0.198 10 false 1 msec./DIV.

Waveform 1:

Camshaft Timing Oil Control Valve
Terminal No. (Symbol) Tool Setting Condition
C75-13 (OC1+) - C75-12 (OC1-) 5 V/DIV., 1 msec./DIV. Idling


c.
A303325
0.365,0.219 1.438,0.406 1.073,0.188 10 false 0.2 V/DIV. 0.625,1.531 1.313,1.688 0.688,0.156 10 false GND 1.792,1.844 2.844,2.073 1.052,0.229 10 false 200 msec./DIV.

Waveform 2:

Heated Oxygen Sensor
Terminal No. (Symbol) Tool Setting Condition
C75-21 (A1A+) - C75-28 (E2) 0.2 V/DIV., 200 msec./DIV. Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In the Data List, item O2S B1S1 shows the value from the heated oxygen sensor which is input to the ECM.



d.
A303304
0.552,0.24 1.26,0.438 0.708,0.198 10 false 20 V/DIV. 0.646,1.563 1.115,1.76 0.469,0.198 10 false GND 1.802,1.896 2.74,2.125 0.938,0.229 10 false 20 msec./DIV.

Waveform 3:

Fuel Injector No. 1 (to No. 4) Injection Signal
Terminal No. (Symbol) Tool Setting Condition
C76-6 (#10) - C75-7 (E01) 20 V/DIV., 20 msec./DIV. Idling
C76-5 (#20) - C75-7 (E01) 20 V/DIV., 20 msec./DIV. Idling
C76-2 (#30) - C75-7 (E01) 20 V/DIV., 20 msec./DIV. Idling
C76-1 (#40) - C75-7 (E01) 20 V/DIV., 20 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



e.
A303309
2.406,0.521 3.104,0.719 0.698,0.198 10 false 1 V/DIV. 2.688,0.979 3.104,1.188 0.417,0.208 10 false GND 1,1.896 1.927,2.104 0.927,0.208 10 false 1 msec./DIV.

Waveform 4:

Knock Sensor
Terminal No. (Symbol) Tool Setting Condition
C75-29 (KNK1) - C75-30 (EKNK) 1 V/DIV., 1 msec./DIV. Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




f.
A303305
2.74,0.083 3.344,0.271 0.604,0.188 10 false 5 V/DIV. 2.823,0.604 3.24,0.833 0.417,0.229 10 false GND 2.833,1.406 3.25,1.635 0.417,0.229 10 false GND 0.323,0.531 0.74,0.76 0.417,0.229 10 false G2 0.344,1.406 0.76,1.635 0.417,0.229 10 false NE 1.229,1.896 2.313,2.094 1.083,0.198 10 false 20 msec./DIV.

Waveform 5:

Crankshaft Position Sensor and Camshaft Position Sensor
Terminal No. (Symbol) Tool Setting Condition
C75-27 (NE+) - C75-34 (NE-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up
C75-26 (G2) - C75-34 (NE-) 5 V/DIV., 20 msec./DIV. Idling after engine warmed up

HINT:

The wavelength becomes shorter as the engine speed increases.



g.
A303306
0.604,0.229 1.292,0.469 0.688,0.24 10 false 2 V/DIV. 0.969,0.708 1.198,0.948 0.229,0.24 10 false (a) 0.49,0.906 1.177,1.146 0.688,0.24 10 false Ground 0.5,1.469 1.188,1.708 0.688,0.24 10 false Ground 0.979,1.281 1.208,1.521 0.229,0.24 10 false (b) 1.865,1.833 2.865,2.031 1,0.198 10 false 20 msec./DIV.

Waveform 6:

Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM)
Terminal No. (Symbol) Tool Setting Condition
(a) C75-17 (IGT1) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) C75-16 (IGT2) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) C75-15 (IGT3) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling
(a) C75-14 (IGT4) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling
(b) C75-23 (IGF1) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



h.
A205411
2.604,0.281 3.229,0.438 0.625,0.156 10 false 10 V/DIV. 1.01,1.927 1.917,2.104 0.906,0.177 10 false 20 msec./DIV. 2.677,1.094 3.042,1.271 0.365,0.177 10 false GND

Waveform 7:

Purge VSV
Terminal No. (Symbol) Tool Setting Condition
C76-23 (PRG) - C75-3 (E1) 10 V/DIV., 20 msec./DIV. Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



i.
A303307
0.458,0.292 1.219,0.479 0.76,0.188 10 false 2 V/DIV. 0.531,1.167 0.969,1.354 0.438,0.188 10 false GND 1.823,1.896 2.979,2.083 1.156,0.188 10 false 20 msec./DIV.

Waveform 8:

Vehicle Speed Signal
Terminal No. (Symbol) Tool Setting Condition
G88-8 (SPD) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



j.
A208000
2.854,1 3.188,1.146 0.333,0.146 10 false GND 2.635,0.229 3.177,0.375 0.542,0.146 10 false 5 V/DIV. 0.5,0.615 0.719,0.76 0.219,0.146 10 false M+ 1.281,1.823 2.104,1.979 0.823,0.156 10 false 1 msec./DIV.

Waveform 9:

Throttle Actuator Positive Terminal
Terminal No. (Symbol) Tool Setting Condition
C75-5 (M+) - C76-3 (ME01) 5 V/DIV., 1 msec./DIV. Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



k.
A245848
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.246,1.82 2.076,1.967 0.83,0.147 10 1 msec./DIV.

Waveform 10:

Throttle Actuator Negative Terminal
Terminal No. (Symbol) Tool Setting Condition
C75-4 (M-) - C76-3 (ME01) 5 V/DIV., 1 msec./DIV. Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



l.
A303308
0.667,2.063 1.281,2.26 0.615,0.198 10 false GND 0.615,0.646 1.229,0.844 0.615,0.198 10 false 5 V/DIV. 1.75,2.708 2.708,2.917 0.958,0.208 10 false 10 msec./DIV.

Waveform 11:

Engine Speed Signal
Terminal No. (Symbol) Tool Setting Condition
G88-1 (TACH) - C75-3 (E1) 5 V/DIV., 10 msec./DIV. Idling

HINT:

The wavelength becomes shorter as the engine speed increases.