Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0335  Crankshaft Position Sensor "A" Circuit  P0339  Crankshaft Position Sensor "A" Circuit Intermittent  


DESCRIPTION

The crankshaft position sensor system consists of a sensor plate and a pickup coil.

The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0335 Crankshaft Position Sensor "A" Circuit When either of the following conditions is met (1 trip detection logic):
·

The crankshaft position sensor signal is missing despite the camshaft position sensor signal inputs being normal after the engine is cranked.

·

No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or less.


·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

No. 2 crankshaft timing sprocket (sensor plate)

·

ECM


Comes on DTC stored
P0339 Crankshaft Position Sensor "A" Circuit Intermittent All of the following conditions are met (1 trip detection logic):
(a) The engine speed is 1000 rpm or more.
(b) No crankshaft position sensor signal for 0.05 seconds or more.
(c) 3 seconds or more have elapsed since the starter signal switched from ON to OFF.
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft

·

ECM


- DTC stored

A063955
2.802,0.594 3.229,0.813 0.427,0.219 10 false GND 2.802,1.417 3.271,1.615 0.469,0.198 10 false GND 0.313,0.594 0.531,0.75 0.219,0.156 10 false G2 0.313,1.417 0.708,1.719 0.396,0.302 10 false NE 1.198,1.948 2.208,2.146 1.01,0.198 10 false 20 msec./DIV. 2.75,0.083 3.396,0.271 0.646,0.188 10 false 5 V/DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

G2 stands for the camshaft position sensor signal and NE stands for the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.



Tester Connection Tool Setting Condition Specified Condition
C75-27 (NE+) - C75-34 (NE-) 5 V/DIV, 20 msec./DIV Idling The correct waveform is as shown
C75-26 (G2) - C75-34 (NE-) 5 V/DIV, 20 msec./DIV Idling The correct waveform is as shown


MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.

If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

COMPONENT OPERATING RANGE

Crankshaft position sensor
·

Crankshaft position sensor output voltage fluctuates while crankshaft revolving

·

34 crankshaft position sensor signals per crankshaft revolution



CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 20 seconds or more.


WIRING DIAGRAM

A247768
0.622,1.726 2.352,1.892 1.73,0.166 10 Crankshaft Position Sensor 5.657,2.174 6.016,2.34 0.36,0.166 10 ECM 0.622,1.572 0.927,1.737 0.304,0.166 10 C6 1.472,0.503 1.712,0.668 0.24,0.166 10 NE 1.453,1.079 1.758,1.245 0.304,0.166 10 NE- 1.332,1.366 1.683,1.531 0.351,0.166 10 GND 5.079,0.507 5.261,0.65 0.182,0.142 10 27 5.079,1.275 5.265,1.418 0.186,0.142 10 34 5.657,2.027 5.94,2.186 0.284,0.159 10 C75 5.341,0.483 5.636,0.633 0.295,0.149 10 NE+ 5.341,1.303 5.636,1.452 0.295,0.149 10 NE- 1.761,0.512 1.862,0.675 0.101,0.163 10 1 1.761,1.27 1.878,1.433 0.118,0.163 10 3 1.761,1.055 1.878,1.218 0.118,0.163 10 2 3.23,1.504 3.805,1.688 0.574,0.184 10 Shielded

CAUTION / NOTICE / HINT

HINT:
·

After performing the procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.

·

Installation condition of the camshaft position sensor

·

Installation condition of the camshaft

·

Connection of the camshaft position sensor connector


·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the intelligent tester. To perform the check, follow the procedures below:

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine.

3.

Turn the intelligent tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315

e.

Start the engine.


f.

Read the values displayed on the intelligent tester while the engine is running.

Standard:

Correct values are displayed.


HINT:
·

To check the engine speed change, display the graph on the intelligent tester.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the intelligent tester remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.




Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the crankshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-1 (NE) - C75-27 (NE+) Always Below 1 Ω
C6-2 (NE-) - C75-34 (NE-) Always Below 1 Ω
C6-1 (NE) or C75-27 (NE+) - Body ground Always 10 kΩ or higher
C6-2 (NE-) or C75-34 (NE-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
a.
BR03795
1.594,1.583 2.448,1.854 0.854,0.271 10 Clearance 0.438,1.76 0.792,1.99 0.354,0.229 10 OK 2.656,1.771 2.979,2.0 0.323,0.229 10 NG

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)

NG

5.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET (TEETH OF SENSOR PLATE)
a.

Check the teeth of the sensor plate.

OK:

Sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE NO. 2 CRANKSHAFT TIMING SPROCKET

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 AND/OR P0339)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Read the DTCs.

Result:
Result Proceed to
No DTC is output A
P0335 or P0339 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B