Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The vehicle speed sensor outputs 4 pulses for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A112414
1.635,1.906 2.667,2.167 1.031,0.26 10 false Transmission 3.135,1.906 4.552,2.135 1.417,0.229 10 false Combination Meter 5.135,1.906 5.729,2.198 0.594,0.292 10 false ECM 2.469,0.427 3.531,0.719 1.063,0.292 10 false Pulse Signal 4.135,0.427 5.229,0.656 1.094,0.229 10 false Pulse Signal

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" While the vehicle is being driven, no vehicle speed signal is input to the ECM (1 trip detection logic).
·

Open or short in speed signal circuit

·

Vehicle speed sensor

·

Combination meter assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated engine speed is 2000 to 5000 rpm and the engine load calculated by the ECM is more than a certain level. If there is no signal from the vehicle speed sensor, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


MONITOR STRATEGY

Required Sensors/Components (Main) Vehicle speed sensor, Combination meter assembly
Required Sensors/Components (Related) Engine coolant temperature sensor, Mass air flow meter, Crankshaft position sensor and Throttle position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 2000 to 5000 rpm

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No pulse input

CONFIRMATION DRIVING PATTERN

A232052
0.656,0.865 1.854,1.094 1.198,0.229 10 false 24 km/h (15 mph) 1.417,2.021 1.938,2.281 0.521,0.26 10 false Idling 0.594,2.375 1.875,2.594 1.281,0.219 10 false Ignition Switch ON 2.385,2.219 2.719,2.458 0.333,0.24 10 false [A] 4.823,0.417 5.125,0.677 0.302,0.26 10 false [B] 6.219,3.229 6.469,3.479 0.25,0.25 10 false [C] 4.021,3.031 6.042,3.333 2.021,0.302 10 false Total of 30 seconds or more

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0500.

13.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A206532
6.281,0.615 6.667,0.844 0.385,0.229 10 false 5 V 5.521,0.885 5.948,1.094 0.427,0.208 10 false SPD 5.354,0.938 5.49,1.094 0.135,0.156 10 false 8 6.031,1.844 6.427,2.031 0.396,0.188 10 false G88 6.031,1.99 6.49,2.188 0.458,0.198 10 false ECM 4.354,1.052 4.625,1.26 0.271,0.208 10 false 2P 3.458,1.052 3.729,1.25 0.271,0.198 10 false 2Q 4.365,0.833 4.646,1.052 0.281,0.219 10 false 26 3.469,0.833 3.76,1.031 0.292,0.198 10 false 26 3.396,1.448 4.698,1.646 1.302,0.198 10 false Junction Connector 2.594,0.938 2.719,1.094 0.125,0.156 10 false 6 0.917,1.042 1.042,1.198 0.125,0.156 10 false 5 1.24,1.875 1.656,2.135 0.417,0.26 10 false G19 2.313,0.948 2.615,1.156 0.302,0.208 10 false +S 1.094,1.031 1.333,1.229 0.24,0.198 10 false SI 1.24,2.021 2.615,2.281 1.375,0.26 10 false Combination Meter 0.104,2.75 1.844,3.042 1.74,0.292 10 false from Speed Sensor (SP1)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Drive the vehicle.


f.

Read the value displayed on the intelligent tester.

OK:

Vehicle speeds displayed on intelligent tester and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-6 (+S) - G88-8 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (ECM - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (ECM - JUNCTION CONNECTOR)
a.

Disconnect the ECM connector.


b.

Disconnect the junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-26 - G88-8 (SPD) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR IS DEFECTIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - JUNCTION CONNECTOR)