DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
The actual values may differ from the values listed in the chart under "Results of real-vehicle check" due to climate, weather conditions, etc.
Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in neutral and all accessory switches should be off.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Ptrl General / -
Ptrl AF Control / Air fuel ratio control system related data
Ptrl AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
Ptrl Throttle / Gasoline throttle system related data
Ptrl Intake Control / Intake control system related data
Ptrl Valve Control / Valve control system related data
Ptrl Misfire / "Misfire" related data
Ptrl Starting / "Difficult to start" related data
Ptrl Rough Idle / "Rough idle" related data
Ptrl Evaporative / Evaporative system related data
Ptrl 2nd Air / Secondary air injection system related data
Ptrl CAT Converter / Catalyst converter related data
Check Mode / Check mode related data
Monitor Status / Monitor status related data
Ignition / Ignition system related data
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transmission system related data
Vehicle Information / Vehicle information
According to the display on the intelligent tester, read the Data List.
The title used for each group of Data List items in this repair manual does not appear on the intelligent tester. However, the name in parentheses after the title, which is a Measurement Group, does appear on the intelligent tester. When the name shown in parentheses is selected on the intelligent tester, all the Data List items listed for that group will be displayed.
Various Vehicle Conditions 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | ·
This is the current vehicle speed. ·
The vehicle speed is detected using the speed sensors. ·
Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped. Stored as Freeze Frame Data: Yes |
| Engine Speed | Engine speed | Min.: 0 rpm, Max.: 16383 rpm | 600 to 700 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.
Stored as Freeze Frame Data: Yes |
| Calculate Load | Load calculated by ECM | Min.: 0%, Max.: 100% | - | This is the engine load calculated based on the estimated intake manifold pressure.
Calculate Load = Estimated intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.) Stored as Freeze Frame Data: Yes |
| MAF | Airflow rate from Mass Air Flow (MAF) meter | Min.: 0 gm/s, Max.: 655.35 gm/s | 1.0 to 4.0 gm/s: Idling
4.0 to 15.0 gm/s: 2500 rpm (without load) |
This is the intake air amount from the mass air flow meter.
Stored as Freeze Frame Data: Yes |
| Atmosphere Pressure | Atmospheric pressure | Min.: 0 kPa, Max.: 255 kPa | Equivalent to atmospheric pressure (absolute pressure) | ·
This value is calculated from the intake air amount. ·
Standard atmospheric pressure: 101 kPa ·
For every 100 m increase in altitude, pressure drops by 1 kPa. This varies by weather. Stored as Freeze Frame Data: Yes |
| Coolant Temp | Coolant temperature | Min.: -40°C, Max.: 140°C | 80 to 95°C (176 to 203°F): After warming up | This is the engine coolant temperature.
Stored as Freeze Frame Data: Yes |
| Intake Air | Intake air temperature | Min.: -40°C, Max.: 140°C | Equivalent to temperature at location of mass air flow meter | ·
After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal. ·
If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted. Stored as Freeze Frame Data: Yes |
| Engine Run Time | Engine run time | Min.: 0 s, Max.: 65535 s | Time after engine start | This is the time elapsed since the engine started.
Stored as Freeze Frame Data: Yes |
| Initial Engine Coolant Temp | Initial engine coolant temperature | Min.: -40°C, Max.: 215°C | - | This is the coolant temperature stored when the ignition switch is turned to ON.
Stored as Freeze Frame Data: Yes |
| Initial Intake Air Temp | Initial intake air temperature | Min.: -40°C, Max.: 140°C | - | This is the intake air temperature stored when the ignition switch is turned to ON.
Stored as Freeze Frame Data: Yes |
| Battery Voltage | Battery voltage | Min.: 0 V, Max.: 65.535 V | 11 to 14 V: Idling | If 11 V or less, characteristics of some electrical components may change.
Stored as Freeze Frame Data: Yes |
Throttle Control (Ptrl Throttle)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1 | Min.: 0%, Max.: 100% | 10 to 22%: Accelerator pedal released
54 to 86%: Accelerator pedal fully depressed |
The accelerator pedal position sensor No. 1 output is converted using 5 V = 100%.
Stored as Freeze Frame Data: Yes |
| Accel Sens. No.2 Volt % | Absolute APP No. 2 | Min.: 0%, Max.: 100% | 12 to 42%: Accelerator pedal released
66 to 98%: Accelerator pedal fully depressed |
The accelerator pedal position sensor No. 2 output is converted using 5 V = 100%.
Stored as Freeze Frame Data: Yes |
| Accel Sensor Out No.1 | APP sensor No. 1 voltage | Min.: 0 V, Max.: 4.98 V | 0.5 to 1.1 V: Accelerator pedal released
2.6 to 4.5 V: Accelerator pedal fully depressed |
This is the raw voltage from the accelerator pedal position sensor No. 1.
Stored as Freeze Frame Data: No |
| Accel Sensor Out No.2 | APP sensor No. 2 voltage | Min.: 0 V, Max.: 4.98 V | 1.2 to 2.0 V: Accelerator pedal released
3.4 to 4.98 V: Accelerator pedal fully depressed |
This is the raw voltage from the accelerator pedal position sensor No. 2.
Accelerator pedal position sensor No. 2 is used to monitor accelerator pedal position sensor No. 1. When there is a malfunction in sensor No. 1, the ECM uses sensor No. 2 to control the engine. Stored as Freeze Frame Data: No |
| Accelerator Idle Position | Whether or not accelerator pedal position sensor detecting released accelerator pedal | ON or OFF | ON: Accelerator pedal released | This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position.
Stored as Freeze Frame Data: No |
| Accel Fully Close #1 (AD) | Accelerator fully closed value No. 1 (AD) | Min.: 0 V, Max.: 4.9 V | - | Stored as Freeze Frame Data:
No |
| Accel Fully Close Learn #1 | Accelerator fully released learned value No. 1 | Min.: 0 deg, Max.: 124.5 deg | - | This is the value of accelerator pedal position sensor No. 1 learned when the accelerator pedal is released.
Stored as Freeze Frame Data: No |
| Accel Fully Close Learn #2 | Accelerator fully released learned value No. 2 | Min.: 0 deg, Max.: 124.5 deg | - | This is the value of accelerator pedal position sensor No. 2 learned when the accelerator pedal is released.
Stored as Freeze Frame Data: No |
| Throttle Sensor Volt % | Absolute throttle position sensor | Min.: 0%, Max.: 100% | ·
10 to 22%: Throttle fully closed ·
66 to 98%: Throttle fully open |
The throttle position sensor No. 1 output is converted using 5 V = 100%.
Stored as Freeze Frame Data: Yes |
| Throttl Sensor #2 Volt % | Throttle sensor position #2 | Min.: 0%, Max.: 100% | ·
42 to 62%: Throttle fully closed ·
92 to 100%: Throttle fully open |
The throttle position sensor No. 2 output is converted using 5 V = 100%.
Stored as Freeze Frame Data: Yes |
| ST1 | Brake pedal signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
This is the stop light switch signal.
Stored as Freeze Frame Data: No |
| System Guard | System guard | ON or OFF | ON | When there is a difference between the target and actual throttle valve opening angles, system guard turns off and stops the electronic throttle control system function.
OFF: Electronic throttle control is stopped. Stored as Freeze Frame Data: No |
| Open Side Malfunction | Open malfunction | ON or OFF | OFF | This parameter indicates a malfunction in the electronic throttle when the throttle valve is open.
Stored as Freeze Frame Data: No |
| Throttle Idle Position | Whether or not throttle position sensor detecting idle | ON or OFF | - | This is a parameter calculated by the ECM.
The value is ON when the throttle is at the idle position and OFF when the throttle is open. Stored as Freeze Frame Data: No |
| Throttle Require Position | Required throttle position | Min.: 0 V, Max.: 4.98 V | - | This is a value calculated by the ECM showing the voltage for the target throttle valve position. It is almost an exact match of the Throttle Position No. 1 value except during very rapid throttle valve movement, such as that used during wheelspin control.
Stored as Freeze Frame Data: No |
| Throttle Sensor Position | Throttle sensor position | Min.: 0%, Max.: 100% | ·
0%: Throttle fully closed ·
50 to 80%: Throttle fully open |
This is the throttle valve opening amount used for engine control.
(100% signifies 125° of throttle valve rotation. This does not include the amount the throttle valve is opened to maintain the idling speed during idling.) This value has no meaning when the ignition switch is ON and the engine is stopped. The throttle valve opening amount during idling is indicated by 0%. When the throttle valve is fully open, the value is 68%. Stored as Freeze Frame Data: Yes |
| Throttle Position No.1 | Throttle position sensor No. 1 output voltage | Min.: 0 V, Max.: 4.98 V | Almost same as "Throttle Require Position"
·
0.5 to 1.1 V: Throttle fully closed ·
3.2 to 4.8 V: Throttle fully open ·
0.6 to 1.4 V: Fail-safe operating |
This is the throttle position sensor No. 1 output voltage.
Stored as Freeze Frame Data: No |
| Throttle Position No.2 | Throttle position sensor No. 2 output voltage | Min.: 0 V, Max.: 4.98 V | ·
2.1 to 3.1 V: Throttle fully closed ·
4.6 to 4.98 V: Throttle fully open ·
2.1 to 3.1 V: Fail-safe operating |
This is the throttle position sensor No. 2 output voltage.
Stored as Freeze Frame Data: No |
| Throttle Position Command | Throttle position command value | Min.: 0 V, Max.: 4.98 V | - | Throttle Position Command is the same value as Throttle Require Position.
Stored as Freeze Frame Data: No |
| Throttle Sens Open Pos #1 | Throttle position sensor No. 1 | Min.: 0 V, Max.: 4.98 V | 0.6 to 0.9 V | This is the throttle position sensor No. 1 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON.
Stored as Freeze Frame Data: No |
| Throttle Sens Open Pos #2 | Throttle position sensor No. 2 | Min.: 0 V, Max.: 4.98 V | 2.2 to 2.6 V | This is the throttle position sensor No. 2 output voltage when there is no current supplied to the electronic throttle actuator. The accelerator pedal is released but the throttle valve is kept open by the throttle valve opener with the ignition switch ON.
Stored as Freeze Frame Data: No |
| Throttle Sens Open #1(AD) | Throttle sensor opener position No. 1 (AD) | Min.: 0 V, Max.: 4.9 V | 0.6 to 0.9 V | Stored as Freeze Frame Data:
No |
| Throttle Motor | Whether or not throttle motor control is permitted | ON or OFF | Idling: ON | Read the value with the ignition switch ON (Do not start engine)
Stored as Freeze Frame Data: No |
| Throttle Motor Current | Throttle actuator current | Min.: 0 A, Max.: 19.9 A | 0 to 3.0 A: Idling | ·
When this value is large but the actual opening angle (Throttle Position No. 1) does not reach the target opening angle (Throttle Require Position), there is an "unable to open" malfunction. ·
This value normally fluctuates around 1 A. Stored as Freeze Frame Data: No |
| Throttle Motor DUTY | Throttle actuator | Min.: 0%, Max.: 100% | 10 to 22%: Idling | This is the output duty ratio of the throttle actuator drive circuit.
Stored as Freeze Frame Data: Yes |
| Throttle Motor Duty (Open) | Throttle actuator duty ratio (open) | Min.: 0%, Max.: 255% | 0 to 40%: Idling | ·
This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal. ·
When the throttle valve is being opened, Throttle Motor Duty (Open) is 20 to 30%. Stored as Freeze Frame Data: No |
| Throttle Motor Duty (Close) | Throttle actuator duty ratio (close) | Min.: 0%, Max.: 255% | 0 to 40%: Idling | This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
Stored as Freeze Frame Data: No |
| Throttle Fully Close Learn | Throttle valve fully closed position (learned value) | Min.: 0 V, Max.: 4.98 V | 0.4 to 1.0 V: Accelerator pedal released | ·
The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle (approximately 4 to 7°, the position when the ignition switch is ON, the accelerator pedal is released and the throttle actuator is off). ·
Learning is performed immediately after the ignition switch is turned to ON. Stored as Freeze Frame Data: No |
| ETCS Actuator Power | Whether or not electric throttle control system power is input | ON or OFF | Idling: ON | Stored as Freeze Frame Data:
No |
| +BM Voltage | +BM voltage | Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Ignition switch ON and system normal | This is the power supply for the electronic throttle actuator. When the power supply is interrupted for approximately 1 second, DTCs P2118 (open circuit) and P0657 (short circuit, ECU malfunction) are stored and the electronic throttle control system enters fail-safe mode (normal operation is not restored until the ignition switch is turned off).
Stored as Freeze Frame Data: No |
| Actuator Power Supply | Actuator power supply | ON or OFF | ON: Idling | If +BM power is lost, this item changes to OFF.
Stored as Freeze Frame Data: No |
| Fail Safe Drive | Whether or not fail-safe function is executed | ON or OFF | ETCS has failed: ON | Stored as Freeze Frame Data:
No |
| Fail Safe Drive (Main CPU) | Whether or not fail-safe function is executed | ON or OFF | ETCS has failed: ON | Stored as Freeze Frame Data:
No |
Fuel System (Ptrl General)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Injector (Port) | Injection period of the No. 1 cylinder | Min.: 0 μs, Max.: 65535 μs | - | This is the injection period of the No. 1 cylinder (the command value from the ECM).
Stored as Freeze Frame Data: Yes |
| Injection Volum (Cylinder1) | Injection volume (cylinder 1) | Min.: 0 ml, Max.: 2.047 ml | 0 to 0.5 ml | This is the fuel injection volume for 10 injections.
Stored as Freeze Frame Data: Yes |
| Fuel Pump/Speed Status | Fuel pump status | ON or OFF | ON: Starter on or engine running | Stored as Freeze Frame Data:
Yes |
EVAP System (Ptrl Evaporative)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Evap Purge Flow | Purge flow | Min.: 0%, Max.: 399.9% | - | This is the percentage of total engine airflow contributed by EVAP purge operation.
(Evap Purge Flow = Purge flow / Engine airflow x 100 (%)) It is based on MAF and a stored value for airflow and controlled by adjusting the duty cycle for the purge VSV. Stored as Freeze Frame Data: Yes |
| Purge Density Learn Value | Purge density learned value | Min.: -200, Max.: 199.993 | - | Purge Density Learn Value is the proportion of the decrease in injection volume (based on the change in the air-fuel ratio feedback compensation value) related to a 1% purge flow rate.
When Purge Density Learn Value is a large negative value, the purge effect is large. The purge density is determined from the change in the air-fuel ratio feedback compensation value when purge flow is introduced. Purge density learning is performed so that the feedback compensation value is 0 +/-2%.
Stored as Freeze Frame Data: Yes |
| EVAP Purge VSV | VSV status for EVAP control | ON or OFF | - | This parameter displays ON when the VSV duty ratio is 30% or more, and displays OFF when the VSV duty ratio is less than 30%.
Stored as Freeze Frame Data: Yes |
Air Fuel Ratio Control 1 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Target Air-Fuel Ratio | Target air fuel ratio | Min.: 0, Max.: 1.99 | 0.8 to 1.2: During idling | This is the target air-fuel ratio used by the ECM.
1.0 is the stoichiometric air-fuel ratio. Values that are more than 1 indicate the system attempting to make the air-fuel ratio leaner. Values that are less than 1 indicate the system attempting to make the air-fuel ratio richer. Stored as Freeze Frame Data: Yes |
Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| O2S B1S1 | Heated oxygen sensor output voltage for Bank 1 Sensor 1 | Min.: 0 V, Max.: 1.275 V | 0 to 1 V | This is the output voltage of the heated oxygen sensor.
Values close to 0 V indicate an air-fuel ratio leaner than the stoichiometric ratio. Values close to 1 V indicate an air-fuel ratio richer than the stoichiometric ratio. During air-fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V. Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor. Results of real-vehicle check when performing the Active Test: Injection Volume: -12.5% ·
O2S B1S1: 0.06 V Injection Volume: +12.5% ·
O2S B1S1: 0.94 V Stored as Freeze Frame Data: Yes |
| Short FT #1 | Short-term fuel trim for bank 1 | Min.: -100%, Max.: 99.2% | -20 to 20% | This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the heated oxygen sensor for feedback.
Stored as Freeze Frame Data: Yes |
| Long FT #1 | Long-term fuel trim for bank 1 | Min.: -100%, Max.: 99.2% | -20 to 20% | The ECM will learn the Long FT values based on Short FT. The goal is to keep Short FT at 0% to keep the A/F mixture at the stoichiometric ratio.
This value is used to determine whether the air-fuel ratio control system is malfunctioning. The condition of the system is determined based on the sum of Short FT and Long FT (excluding times when the system is in transition). ·
+15% or more: The air-fuel ratio may be lean. ·
-15 to +15%: The air-fuel ratio can be determined to be normal. ·
-15% or less: The air-fuel ratio may be rich. The learned value is cleared when the battery cable is disconnected. Stored as Freeze Frame Data: Yes |
| Fuel System Status #1 | Fuel system status for bank 1 | OL, CL, OL Drive, OL Fault or CL Fault | CL: Idling after warming up | ·
OL (Open Loop): Has not yet satisfied conditions to go to closed loop. ·
CL (Closed Loop): Uses feedback to perform fuel control. ·
OL Drive: Open loop due to driving conditions (fuel enrichment). ·
OL Fault: Open loop due to a detected system fault. ·
CL Fault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning. CL (Closed Loop): During air-fuel ratio feedback control, O2S B1S1 is approximately 0.45 V. Stored as Freeze Frame Data: Yes |
| O2FT B1S1 | Short-term fuel trim associated with bank 1 sensor 1 | Min.: -100%, Max.: 99.2% | -20 to 20% | This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the heated oxygen sensor for feedback.
Stored as Freeze Frame Data: Yes |
Ignition System (Ignition)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| IGN Advance | Ignition timing advance for No. 1 cylinder | Min.: -64 deg., Max.: 63.5 deg. | BTDC 0 to 20 deg.: Idling | Stored as Freeze Frame Data:
Yes |
| Knock Feedback Value | Knocking feedback value | Min.: -1024° CA, Max.: 1023.9° CA | - | This is the ignition timing retard compensation amount determined by the presence or absence of knocking.
Ignition timing = Most retarded timing value*1 + Knock Correct Learn Value*2 + Knock Feedback Value*3 + each compensation amount Example: 21°CA = 10° + 14° - 3° *1: The most retarded timing value is a constant determined by the engine speed and engine load. *2: The knock correction learned value is calculated as shown below in order to keep Knock Feedback Value as close to -3°CA as possible. When Knock Feedback Value is less than -4°CA, Knock Correct Learn Value is slowly decreased. When Knock Feedback Value is more than -2°CA, Knock Correct Learn Value is slowly increased. *3: The base value is -3°CA and is adjusted based on the presence or absence of knocking. When there is no knocking, the value is increased, and when knocking is present, the value is decreased. -1°CA: There is no knocking and ignition timing is advanced. -6°CA: Knocking is present and the ignition timing is being retarded.
Stored as Freeze Frame Data: Yes |
| Knock Correct Learn Value | Knocking correction learned value | Min.: -1024° CA, Max.: 1023.9° CA | - | Refer to "Knock Feedback Value".
When there is knocking or a lack of power, compare the following values to another vehicle of the same model. ·
Engine speed ·
Calculate Load ·
IGN Advance ·
Knock Feedback Value ·
Knock Correct Learn Value Knock Correct Learn Value is large: There is no knocking and the ignition timing is advanced. Knock Correct Learn Value is small: Knocking is present and the ignition timing is being retarded.
Stored as Freeze Frame Data: Yes |
VVT Control (Ptrl Valve Control)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| VVT Control Status #1 | Variable Valve Timing (VVT) control status for bank 1 | ON or OFF | - | ON: The ECM is sending commands to change the timing (even when the timing is advanced, when the timing is being maintained and not being retarded or advanced any further, the value changes to OFF).
OFF: The system is commanding the timing to change to the most retarded timing. Stored as Freeze Frame Data: Yes |
| VVT Aim Angle #1 | VVT hold duty learned value for bank 1 | Min.: 0%, Max.: 100% | - | This value represents the duty ratio necessary to operate the camshaft timing oil control valve in order to block the camshaft timing oil control valve path and maintain the advanced state of the camshaft timing gear. This is only available during the Active Test.
Refer to "VVT OCV Duty #1". Stored as Freeze Frame Data: No |
| VVT Change Angle #1 | VVT displacement angle for bank 1 | Min.: 0 DegFR, Max.: 639.9 DegFR | - | This is the VVT displacement angle during forced operation.
This is only available during the Active Test. By checking VVT Change Angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output. Refer to "VVT OCV Duty #1". Stored as Freeze Frame Data: No |
| VVT OCV Duty #1 | VVT camshaft timing oil control valve operation duty for bank 1 | Min.: 0%, Max.: 100% | - | This is the requested duty value for forced operation.
This is only available during the Active Test. Results of the real-vehicle check when performing the Control the VVT Linear (Bank 1) Active Test: VVT OCV Duty #1 = 0%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 30%, VVT Change Angle #1 = 0 DegFR ↓ VVT OCV Duty #1 = 70%, VVT Change Angle #1 = 39.0 DegFR ↓ VVT OCV Duty #1 = 100%, VVT Change Angle #1 = 39.0 DegFR ↓ VVT OCV Duty #1 = 32%, VVT Change Angle #1 = 0 DegFR After the above test, VVT Aim Angle #1 = 26.6%. Stored as Freeze Frame Data: No |
Various Vehicle Conditions 2 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Starter Signal | Starter signal | Open or Close | Open: Starter operating
Close: Starter not operating |
Stored as Freeze Frame Data:
Yes |
| Power Steering Signal | Power steering switch signal | ON or OFF | ON: Power steering operating | Stored as Freeze Frame Data:
Yes |
| Power Steer. Sig. Record | Power steering switch signal | ON or OFF | ON: When steering wheel is first turned after ignition switch is turned to ON | This signal status usually ON until ignition switch turned to OFF
Stored as Freeze Frame Data: Yes |
| Stop Light Switch | Stop light switch | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
Stored as Freeze Frame Data:
Yes |
| A/C Signal | A/C status | ON or OFF | ON: A/C on | Stored as Freeze Frame Data:
Yes |
| Closed Throttle Position SW | Closed throttle position switch | ON or OFF | ·
ON: Throttle fully closed ·
OFF: Throttle open |
Stored as Freeze Frame Data:
Yes |
| Electrical Load Signal | Electrical load signal | ON or OFF | ON: Headlights or defogger is turned ON | Stored as Freeze Frame Data:
Yes |
Check Mode (Check Mode)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Check Mode | Check mode | ON or OFF | ON: Check mode on | *
Stored as Freeze Frame Data: No |
| SPD Test Result | Check mode result for vehicle speed sensor | Compl or Incmpl | - | Stored as Freeze Frame Data:
No |
*: Refer to Check Mode Procedure (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/o Secondary Air Injection System)>CHECK MODE PROCEDURE)
Various Vehicle Conditions 3 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| # Codes(Include History) | Number of codes | Min.: 0, Max.: 255 | 0 | This is the number of DTCs stored.
Stored as Freeze Frame Data: No |
| MIL | MIL status | ON or OFF | OFF | Stored as Freeze Frame Data:
No |
| Time after DTC Cleared | Time after DTCs cleared | Min.: 0 minutes, Max.: 65535 minutes | Time after DTCs cleared | This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted.
Stored as Freeze Frame Data: Yes |
| Distance from DTC Cleared | Distance driven after DTCs cleared | Min.: 0 km, Max.: 65535 km | Distance driven after DTCs cleared | This is the distance driven after DTCs were cleared (or after the vehicle left the factory).
Stored as Freeze Frame Data: Yes |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | Min.: 0, Max.: 255 | - | This is the number of warmup cycles after the DTCs were cleared.
This is the number of times the engine was warmed up* after DTCs were cleared (or after the vehicle left the factory). *: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or more and reaching a temperature of 70°C (158°F) or higher after the engine is started. Stored as Freeze Frame Data: Yes |
| OBD Requirements | OBD requirement | - | Not OBD compliant | Stored as Freeze Frame Data:
No |
| Number of Emission DTC | Emissions-related DTCs | - | - | This is the number of emissions-related DTCs.
Stored as Freeze Frame Data: No |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | ON or OFF | - | Stored as Freeze Frame Data:
Yes |
Various Vehicle Conditions 4 (All Data)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ACT VSV | A/C cut status | ON or OFF | - | Stored as Freeze Frame Data:
Yes |
| Idle Fuel Cut | Fuel cut at idle | ON or OFF | ON: Fuel cut operating | Idle Fuel Cut = "ON" when the throttle valve is fully closed and the engine speed is high.
Stored as Freeze Frame Data: Yes |
| FC TAU | Fuel cut TAU (fuel cut during very light load) | ON or OFF | ON: Fuel cut operating | This is the fuel cut performed under a very light load to prevent the engine combustion from becoming incomplete.
Stored as Freeze Frame Data: Yes |
Various Vehicle Conditions 5 (Vehicle Information)
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Model Code | Model code | - | - | Used for identifying the model code: TGN###
Stored as Freeze Frame Data: No |
| Engine Type | Engine type | - | - | Used for identifying the engine type: 2TRFE
Stored as Freeze Frame Data: No |
| Cylinder Number | Number of cylinders | Min.: 0, Max.: 255 | - | Used for identifying the number of cylinders: 4
Stored as Freeze Frame Data: No |
| Transmission Type | Transmission type | - | - | Used for identifying the transmission type: MT
Stored as Freeze Frame Data: No |
| Destination | Destination | - | - | Used for identifying the destination: W
Stored as Freeze Frame Data: No |
| Model Year | Model year | Min.: 1900, Max.: 2155 | - | Used for identifying the model year: 20##
Stored as Freeze Frame Data: No |
| System Identification | System identification | - | - | Used for identifying the engine system: Gasoline (gasoline engine)
Stored as Freeze Frame Data: No |
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the intelligent tester, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Injection Volume | Change injection volume | Between -12.5% and 24.8% | ·
All injectors are tested at the same time. ·
Perform the test at 3000 rpm or less. ·
Injection volume can be changed in fine gradations within the control range. ·
Control the Injection Volume enables the checking and graphing of the heated oxygen sensor voltage output. ·
To conduct the test, enter the following menus: Active Test / Control the Injection Volume / O2S B1S1. ·
During the Active Test, air-fuel ratio feedback control and feedback learning are stopped. |
| Control the Injection Volume for A/F Sensor | Change injection volume | -12.5%, 0% or +12.5% | ·
All injectors are tested at the same time. ·
Perform the test at 3000 rpm or less. ·
Control the Injection Volume for A/F Sensor enables the checking and graphing of the heated oxygen sensor voltage output. ·
To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1. ·
During the Active Test, air-fuel ratio feedback control and feedback learning are stopped. ·
See waveform*1. |
| Activate the VSV for Evap Control | Activate purge VSV control | ON/OFF | ·
The valve is opened with a 30% duty ratio. ·
See waveform*3. |
| Control the A/C Cut Signal | A/C compressor cut | ON/OFF | - |
| Control the Fuel Pump / Speed | Activate fuel pump | ON/OFF | Perform this test with the engine stopped. |
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON/OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. |
| Control the Idle Fuel Cut Prohibit | Prohibit idling fuel cut control | ON/OFF | - |
| Control the ETCS Open/Close Slow Speed | Throttle actuator | Close/Open
Open: Throttle valve opens slowly |
This test is possible when the following conditions are met:
·
Ignition switch is ON. ·
Engine is stopped. ·
Accelerator pedal is fully depressed (APP: 58 degrees or more). ·
Shift lever is in neutral. |
| Control the ETCS Open/Close Fast Speed | Throttle actuator | Close/Open
Open: Throttle valve opens quickly |
·
Same as above. ·
See waveform*2. |
| Control the VVT Linear (Bank1) | Control VVT (for intake side of bank 1) | -128 to 127% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance -100%: Maximum retard |
·
Engine stalls or idles roughly when the camshaft timing gear is operated by 100%. ·
Test is possible during idle. ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. ·
See waveform*4. |
| Control the VVT System (Bank1) | Turn camshaft timing oil control valve on and off | ON/OFF
ON: VVT OCV Duty #1 100% |
·
Engine stalls or idles roughly when the camshaft timing oil control valve is turned on. ·
Engine runs and idles normally when the camshaft timing oil control valve is off. ·
DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction. |
| Control the Select Cylinder Fuel Cut | Selected cylinder (cylinder #1 to #4) injector fuel cut | ON/OFF | Test is possible while the vehicle is stopped and the engine is idling. |
| Control the All Cylinders Fuel Cut | Fuel cut for all cylinders | ON/OFF | Test possible while the vehicle is stopped and the engine is idling. |
*1: Control the Injection Volume for A/F Sensor (Idling after warming up)
During the Active Test, air-fuel ratio feedback control and feedback learning are stopped.
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the Injection Volume for A/F Sensor | - | ▲A | ▲B |
| Active Test operation | -12.5% | +12.5% | |
| O2S B1S1 | 0.03 V | 0.85 V | |
Usually, the value of O2S changes to 0.55 V or higher when the control value for Control the Injection Volume for A/F Sensor is changed to +12.5%.
Usually, the value of O2S drops below 0.4 V when the control value for Control the Injection Volume for A/F Sensor is changed to -12.5%.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
*2: Control the ETCS Open/Close Fast Speed [Active Test for electrical throttle control system] (Ignition switch ON)
Usually, Throttle Position Command (Target Value) and Throttle Position No. 1 (Actual Value) are almost the same.
If any DTCs related to the ETCS are stored, this Active Test does not function.
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the ETCS Open/Close Fast Speed | - | ▲A | ▲B |
| Active Test operation | Close | Open | |
| Throttle Position Command | 2.597 V | 0.742 V | |
| Throttle Position No. 1 | 2.597 V | 0.742 V | |
| Throttle Motor Duty (Open) | 14% | 0% | |
| Throttle Motor Duty (Close) | 0% | 10% | |
*3: Activate the VSV for Evap Control (Idling after warming up)
Even when the Active Test is turned on (the purge VSV is opened 30%), air-fuel ratio feedback continues and control is performed so that the air-fuel ratio is the stoichiometric ratio. Therefore, by observing the change in "Short FT", it is possible to determine whether the purge VSV is actually open as well as the concentration of HC in the purge gas.
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Activate the VSV for Evap Control | - | ▲A | ▲B |
| Active Test operation | ON | OFF | |
| EVAP Purge VSV | ON | OFF | |
| Short FT #1 | -1.563% | 0.000% | |
| Injection (Port) | 2288.0 μs | 2430.0 μs | |
| O2S B1S1 | 0.85 V | 0.03 V | |
The graphs and values above are for reference only because the fuel injection volume (compensation volume) varies depending on the HC density of the purge air from the canister.
*4: Control the VVT Linear (Bank 1)
| Tester Display | Measurement Item/Range | Normal Condition | |
|---|---|---|---|
| Control the VVT Linear (Bank 1) | - | ▲A | ▲B |
| Active Test operation* | +20% | -20% | |
| VVT Change Angle #1 | 54.9 DegFR | 0.0 DegFR | |
| VVT OCV Duty #1 | 53.9% | 13.9% | |
| VVT Aim Angle #1 | 33.9% | 33.9% | |
*: Change the control value for Control the VVT Linear to +20% or -20% in increments of 5%.
The Control the VVT Linear Active Test considers the value of VVT Aim Angle to be 0 and raises or lowers the duty ratio with respect to VVT Aim Angle.
The sum of the control value for the Control the VVT Linear Active Test and the value of VVT Aim Angle is approximately equal to the value of VVT OCV Duty.
When the control value for the Control the VVT Linear Active Test is changed a few times, there should not be a large discrepancy between VVT OCV Duty when the system starts advancing or retarding the timing and the rate of change of VVT Change Angle.