Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) J

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A240424
4.396,1.115 6.219,1.292 1.823,0.177 10 false 5 V Constant Voltage Circuit 5.375,1.948 6.385,2.365 1.01,0.417 10 false Microprocessor 1.531,1.469 2.76,1.75 1.229,0.281 10 false from MAIN Relay 1.688,1.125 2.698,1.354 1.01,0.229 10 false from EFI Fuse 2.917,1.01 3.438,1.229 0.521,0.219 10 false BATT 0.313,2.063 2.635,2.573 2.323,0.51 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.313,2.948 2.583,3.344 2.271,0.396 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.125 4.333,3.333 0.26,0.208 10 false R 2.99,1.354 3.344,1.552 0.354,0.198 10 false +B 3.167,2.26 3.458,2.49 0.292,0.229 10 false VC 4.885,0.51 5.333,0.74 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A247784
6.125,5.344 6.469,5.5 0.344,0.156 10 false ECM 5.385,0.406 5.573,0.563 0.188,0.156 10 false 18 5.646,0.469 5.875,0.625 0.229,0.156 10 false VC 5.333,0.563 5.615,0.708 0.281,0.146 10 false C75 5.333,0.958 5.615,1.104 0.281,0.146 10 false C75 5.333,1.354 5.615,1.5 0.281,0.146 10 false C75 5.333,1.76 5.615,1.906 0.281,0.146 10 false C75 5.396,0.802 5.583,0.958 0.188,0.156 10 false 20 5.396,1.208 5.583,1.365 0.188,0.156 10 false 19 5.396,1.604 5.583,1.76 0.188,0.156 10 false 28 5.646,0.958 6.031,1.104 0.385,0.146 10 false VTA1 5.646,1.354 6.031,1.5 0.385,0.146 10 false VTA2 5.646,1.677 5.844,1.823 0.198,0.146 10 false E2 5.385,2.667 5.573,2.813 0.188,0.146 10 false 26 5.323,2.823 5.615,2.969 0.292,0.146 10 false G89 5.323,3.229 5.615,3.375 0.292,0.146 10 false G89 5.323,3.625 5.615,3.771 0.292,0.146 10 false G89 5.323,4.052 5.615,4.198 0.292,0.146 10 false G89 5.323,4.458 5.615,4.604 0.292,0.146 10 false G89 5.323,4.854 5.615,5 0.292,0.146 10 false G89 5.385,3.063 5.573,3.208 0.188,0.146 10 false 27 5.385,3.469 5.573,3.615 0.188,0.146 10 false 18 5.385,3.896 5.573,4.042 0.188,0.146 10 false 19 5.385,4.302 5.573,4.448 0.188,0.146 10 false 20 5.385,4.698 5.573,4.844 0.188,0.146 10 false 21 5.646,2.74 6.052,2.896 0.406,0.156 10 false VCPA 5.646,3.625 5.958,3.781 0.313,0.156 10 false VPA 5.646,4.375 5.958,4.531 0.313,0.156 10 false EPA 5.646,4.052 6.021,4.208 0.375,0.156 10 false VPA2 5.646,4.771 6.021,4.927 0.375,0.156 10 false EPA2 5.646,3.146 6.052,3.302 0.406,0.156 10 false VCP2 0.219,2.073 0.5,2.229 0.281,0.156 10 false C67 0.219,2.219 1.74,2.375 1.521,0.156 10 false Throttle Position Sensor 2.594,0.552 2.833,0.708 0.24,0.156 10 false VC 2.531,0.948 2.833,1.104 0.302,0.156 10 false VTA 2.448,1.344 2.823,1.51 0.375,0.167 10 false VTA2 2.625,1.75 2.844,1.917 0.219,0.167 10 false E2 2.906,0.469 3.021,0.625 0.115,0.156 10 false 5 2.906,0.865 3.021,1.021 0.115,0.156 10 false 6 2.906,1.271 3.021,1.427 0.115,0.156 10 false 4 2.906,1.667 3.021,1.823 0.115,0.156 10 false 3 0.208,5.167 0.438,5.323 0.229,0.156 10 false G6 0.208,5.313 2.375,5.5 2.167,0.188 10 false Accelerator Pedal Position Sensor 2.438,2.823 2.854,2.969 0.417,0.146 10 false VCPA 2.438,3.219 2.854,3.365 0.417,0.146 10 false VCP2 2.51,3.625 2.896,3.771 0.385,0.146 10 false VPA 2.438,4.063 2.854,4.208 0.417,0.146 10 false VPA2 2.5,4.448 2.823,4.594 0.323,0.146 10 false EPA 2.438,4.854 2.865,5 0.427,0.146 10 false EPA2 2.906,2.729 3.021,2.885 0.115,0.156 10 false 4 2.906,3.135 3.021,3.292 0.115,0.156 10 false 1 2.906,3.531 3.021,3.688 0.115,0.156 10 false 6 2.906,3.969 3.021,4.125 0.115,0.156 10 false 3 2.906,4.375 3.021,4.531 0.115,0.156 10 false 5 2.906,4.76 3.021,4.917 0.115,0.156 10 false 2

PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Check the communication between the intelligent tester and ECM.

Result:
Result Proceed to
Communication is possible A
Communication is not possible B




A

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



A

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

B

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.


Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

B

5.CHECK HARNESS AND CONNECTOR
5.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor connector.


b.

Disconnect the accelerator pedal position sensor connector.


c.

Disconnect the ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-18 (VC) - Body ground Always 10 kΩ or higher
G89-26 (VCPA) - Body ground Always 10 kΩ or higher
G89-27 (VCP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR